Effects of post-weld heat treatments on dissimilar joints of rigid pipes made of API X65 steel and Inconel 625 for offshore applications
Source abstract
Abstract
This paper evaluated the effects of different post-weld heat treatment (PWHT) routes on the microstructural, mechanical, and electrical behavior of dissimilar welded joints be-tween API X65 steel and Inconel 625, widely used in offshore systems such as risers and mechanically lined pipes. Welded specimens were analyzed in four conditions: as-welded (AW), stress-relieved (SR), quenched (Q), and quenched followed by tempering (QT). Microstructural analysis, Rockwell C hardness testing, and electrical resistivity measurements using a four-point probe method were applied to assess joint performance across regions such as the base metal, weld metal, and heat-affected zones (HAZ 1, HAZ 2, HAZ 3). In the AW condition, hardness varied significantly (e.g., 11 HRC in base metal and 35 HRC in HAZ 2), and resistivity ranged from 17.80 to 120.50 μΩ·m, indicating localized hardening and residual stress. After PWHT, hardness became more uniform (17–25 HRC), and resistivity increased but stabilized (52.80–63.00 Ω·m), reflecting improved homogeneity. The treatments reduced internal stress, refined microstructures, and promoted more predictable electrical behavior. These findings support the effectiveness of combined PWHT (SR + Q + QT) in enhancing the integrity of dissimilar joints, contributing to safer and more durable offshore pipeline applications.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Structural Integrity and Reliability Analysis · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (93)
Show source-provided references
1. Exploratory assessment of the economic gains of a pre-salt oil field in Brazil10.1016/j.enpol.2015.09.036 ↗
2. 2024
3. Measuring the economic impact of pre-salt layer on the productivity of the oil and natural gas sector10.3390/resources14020032 ↗
4. Influence of the mechanical properties of materials on the ultimate pressure-bearing capability of a pressure-preserving controller10.1016/j.petsci.2024.04.003 ↗
5. Materials and corrosion trends in offshore and subsea oil and gas production10.1038/s41529-017-0003-4 ↗
6. Defects and fatigue properties of LPDC-fabricated aluminum alloy wheel: experimental and numerical simulation methods10.1016/j.engfailanal.2025.110074 ↗
7. Investigating an API X65 steel pipe cladded with alloy 625
8. Metallurgical aspects in the welding of clad pipelines-A global outlook10.3390/app9153118 ↗
9. Microstructure and corrosion properties of single layer Inconel 625 weld cladding obtained by the electroslag welding process10.1016/j.jmrt.2020.11.048 ↗
10. Partially diluted zones in dissimilar cladding with AWS ER NiCrMo-3 alloy deposited by the MIG process on ASTM A36 steel: analysis and characterization by EBSD
11. Interface characterization and mechanical properties of laser powder bed fused IN718-CuSn10 functionally gradient materials
12. Effects of thermal history of in-situ thermal management on as-built property heterogeneity of plasma arc additively manufactured Inconel 62510.1016/j.jmrt.2023.06.090 ↗
13. Effect of welding torch mode on heat input, microstructure, and mechanical performance of inconel 625 via wire-arc-directed energy deposition10.1002/adem.202401801 ↗
14. Microstructural evolution and mechanical properties of FCAW joints in 9% Ni steel prepared with two types of Ni-Based weld metals10.1007/s00170-022-09173-5 ↗
15. A comprehensive review of residual stresses in carbon steel welding: formation mechanisms, mitigation strategies, and advanced post-weld heat treatment techniques10.1007/s00170-025-15088-8 ↗
16. 2013
17. ISO 15156-1:2020 - Petroleum and natural gas industries — materials for use in H2S-containing environments in oil and gas production. Part 1: general principles for selection of cracking-resistant materials
18. Performance of the INCONEL 625 alloy weld overlay obtained by FCAW process
19. Effect of aging treatment on microstructure, mechanical properties and corrosion resistance of 2219 aluminium alloy laser welded joint10.1016/j.jmrt.2025.10.148 ↗
20. Effect of the thermal history on macrostructure and microstructure development in high-strength steel welds10.1007/s11661-022-06686-2 ↗
21. Structure evolution of Fe- and Co-Based amorphous alloys studied by the electrical resistivity measurements10.4028/www.scientific.net/SSP.215.185 ↗
22. Effects of interface density on mechanical and electrical properties of annealed Cu–Nb nanocomposite wires10.1016/j.msea.2022.144001 ↗
23. Synergistic effects of chemical composition on precipitates, dislocations, and mechanical properties of precipitation-strengthened alloys10.1016/j.msea.2024.146635 ↗
24. Collapse pressure prediction of mechanically lined pipes using FEM and machine learning techniques10.1016/j.oceaneng.2022.113418 ↗
25. Mechanical analysis of lined pipe System under temperature–pressure coupling in elastic laying10.3390/pr13030691 ↗
26. Metastable microstructure evolution and grain refinement in a Low-Ta containing γ-TiAl alloy through heat treatment10.1016/j.jmrt.2024.02.095 ↗
27. Experimental analysis of the stability of retained austenite in a low-alloy 42CrSi steel after different quenching and partitioning heat treatments10.1002/adem.202300380 ↗
28. Microstructure-Impact toughness evolution of ultrahigh strength steel: influence of quenching and secondary low-temperature tempering
29. Mechanical degradation behavior and γ′ coarsening mechanism of a Ni-based superalloy during long-term high-temperature thermal exposure10.1016/j.jmrt.2024.05.270 ↗
30. Análise microestrutural em tubos de aço inoxidável superduplex com revestimento de Inconel como reparo para perfurações por corrosão localizada
31. Role of Ni content on microstructural and mechanical responses of Nb-stabilized metastable austenitic stainless steel weld metals10.1016/j.jmrt.2023.09.182 ↗
32. Evolution mechanism of interfacial microstructure and its effect on failure in dissimilar metal welds containing ferritic heat resistant steels10.1016/j.jmrt.2023.09.036 ↗
33. Investigations into the microstructure and texture evolution of10.3390/met13091575 ↗
34. Microstructural evaluation of inconel 718 and AISI 304L dissimilar TIG joints10.3390/met14010054 ↗
35. Synergistic effects of thermal cycles and residual stress on microstructural evolution and mechanical properties in Monel 400 and AISI 316L weld joints10.3390/met15050469 ↗
36. Medidas De Resistividade Elétrica DC Em Sólidos: comoefetuá-las Corretamente
37. Approaches to measure the resistivity of grain boundaries in metals with high sensitivity and spatial resolution: a case study employing Cu10.1021/acsaelm.0c00311 ↗
38. Optimization of heating profile for superconductor joint performance made by resistive joule heating process10.1016/j.jmrt.2023.12.110 ↗
39. Microstructure characterization and its relationship with impact toughness of C–Mn and high strength low alloy steel weld metals – a review10.1016/j.jmrt.2020.12.006 ↗
40. Quantitative relationship between microstructure/crystallography and strength/toughness in simulated inter-critical heat affected subzone of medium Mn steel10.1016/j.jmrt.2022.12.113 ↗
41. Evaluation of microstructure and mechanical properties of Fe–1.2Mn–0.3Cr–1.4Ni–0.4Mo–C steel welded joints10.1016/j.jmrt.2020.09.135 ↗
42. Two-pass friction stir welding of cladded API X6510.1016/j.promfg.2020.04.311 ↗
43. Microstructure and microhardness evolution of thermal simulated HAZ of Q& P980 steel10.1016/j.jmrt.2021.11.059 ↗
44. Incompleteness of bainite transformation in quenched and tempered steel under continuous cooling conditions10.1016/j.jmrt.2020.06.039 ↗
45. A review on fusion welding of dissimilar ferritic/austenitic steels: processing and weld zone metallurgy
46. DuPont · 2009
47. Modeling of welding residual stress in a dissimilar metal butt-welded joint between P92 ferritic steel and SUS304 austenitic stainless steel10.1016/j.jmrt.2023.02.123 ↗
48. High-efficiency fabrication of Inconel 625 coating for AISI 1045 carbon steel through laser cladding with hot wire: microstructure and wear resistance10.1016/j.jmapro.2023.07.063 ↗
49. Formation and deformation mechanism of the hierarchical diffusion layer in the laminated Ti/Ti–50Nb alloy10.1016/j.msea.2023.144996 ↗
50. Fatigue behavior and microstructural evaluation of Inconel 718 gas tungsten arc welds10.1007/s40194-021-01190-4 ↗
51. Stress rupture initiated by the carbides in the grain boundaries of the multi-pass weld metal10.1016/j.jmrt.2020.12.031 ↗
52. Welding, brazing, and soldering handbook
53. Electron microscopy study of laser welded GH909 superalloy joint10.1016/j.jmrt.2020.10.049 ↗
54. Evolution of microsegregation-induced precipitations and bending fracture mechanisms of 9% Ni steel weldments filled with nickel-based alloys10.1016/j.jmrt.2023.07.178 ↗
55. Microstructural analysis of partially diluted zones in dissimilar cladding: EBSD insights on AWS E 309L alloy via MIG process in Single- and double-layer depositions on ASTM A36 steel
56. Heat treatment of steels
57. Totten · 2006
58. Effect of rapid tempering at high temperature on microstructure, mechanical properties and stability of retained austenite of medium carbon ultrafine bainitic steel10.1016/j.jmrt.2023.12.238 ↗
59. Fretting wear of inconel 625 at high temperature and in high vacuum10.1016/0043-1648(85)90108-5 ↗
60. Microstructural evolution and mechanical properties of inconel 625 alloy during pulsed plasma arc deposition process10.1016/j.jmst.2013.02.010 ↗
61. Effect of stress-relief heat treatments on the microstructure and mechanical response of additively manufactured IN625 thin-walled elements10.1016/j.msea.2022.143288 ↗
62. Effect of residual stress on pore formation in multi-materials deposited via directed energy deposition
63. Weld morphology and grain growth characteristics of driven moving arc hollow stud welding10.1016/j.jmrt.2023.05.138 ↗
64. Effect of heat input on mechanical and metallurgical properties of gas tungsten arc welded lean super martensitic stainless steel10.1590/1980-5373-MR-2015-0538 ↗
65. Effect of welding process on the microstructure and properties of dissimilar weld joints between low alloy steel and duplex stainless steel10.1007/s12613-012-0589-z ↗
66. Preparation of ultrafine acicular α’ phase titanium alloys via laser melting deposition: achieving synergistic enhancement of strength and corrosion resistance10.1016/j.jallcom.2025.184126 ↗
67. Introduction to steel heat treatment10.1016/B978-0-08-096532-1.01202-4 ↗
68. Influence of microstructural length scale on the strength and annealing behavior of pearlite, bainite, and martensite10.1007/s11661-012-1501-1 ↗
69. Improving wear resistance of steels through nanocrystalline structures obtained by bainitic transformation10.1080/02670836.2015.1132048 ↗
70. On the microstructure and dynamic mechanical behavior of Cu–Cr–Zr alloy manufactured by high-power laser powder bed fusion10.1016/j.matdes.2025.113826 ↗
71. Influence of molten-pool cooling rate on solidification structure and mechanical property of laser additive manufactured Inconel 71810.1016/j.jmrt.2022.06.162 ↗
72. Mechanical and microstructural characteristics of inconel 625 alloy after exposure to elevated temperature and H2SO4 solution quenching10.1007/s40032-024-01158-5 ↗
73. A numerical study of dendrite growth and microstructure transition in a non-equilibrium solidification10.1088/1742-6596/1939/1/012018 ↗
74. Geddes
75. Effects of nitride precipitation on delta phase formation in additively manufactured nickel superalloys10.1016/j.jallcom.2023.172936 ↗
76. Effects of Mo and Nb on the microstructure and high temperature oxidation behaviors of CoCrFeNi-based high entropy alloys10.1016/j.jmrt.2023.10.058 ↗
77. Effect of cryogenic treatment on the microstructure and mechanical properties of selected laser melted H13 steel10.1016/j.jmrt.2022.11.068 ↗
78. Effects of tempering temperature on the microstructure evolution and mechanical properties of 16%Cr–5%Ni super martensitic stainless steel10.1016/j.jmrt.2023.05.165 ↗
79. EBSD microstructural studies on quenched-tempered API 5L X65 pipeline steel10.1080/14786435.2021.1946189 ↗
80. Weakening modes for the heat affected zone in Inconel 625 superalloy welded joints under different high temperature rupture conditions10.1016/j.jmrt.2021.07.156 ↗
81. Optimizing tempering parameters to enhance precipitation behavior and impact toughness in high-nickel steel10.3390/met14080898 ↗
82. Effects of the γ″-Ni3Nb phase on fatigue behavior of nickel-based 718 superalloys with different heat treatments10.3390/ma12233979 ↗
83. Microstructure evolution and enhanced cryogenic toughness of laser welded dissimilar SA645/AISI304L joints via intercritical tempering10.1016/j.jmrt.2024.03.036 ↗
84. Investigation of boundaries and structures in dissimilar metal welds10.1179/stw.1998.3.5.249 ↗
85. Effects of austenizing temperature, cooling rate and isothermal temperature on overall phase transformation characteristics in high carbon steel10.1016/j.jmrt.2020.10.071 ↗
86. Microstructure anomaly during welding and its influence on the mechanical properties of dissimilar weldments of P92 martensitic steel and AISI 304L austenitic stainless steel Author links open overlay panel10.1016/j.jmapro.2022.06.048 ↗
87. The influence of microstructure on the electromagnetic behavior of carbon steel wires10.3390/cryst12050576 ↗
88. Homogenization of microstructure and mechanical properties of wire arc additive manufactured martensitic stainless steel through optimization of post-process heat treatment10.1016/j.jmrt.2022.10.077 ↗
89. Revisiting the dependence of electrical resistivity on Cu-Rich precipitates in an aged Fe-Cu model alloy: a microstructure-based prediction model10.3390/ma18040752 ↗
90. Microstructure evolution and mechanical properties of X12CrMoWVNbN10-1-1 steel during quenching and tempering process10.1016/j.jmrt.2015.06.001 ↗
91. Optimizing dislocation strengthening in high-strength medium-carbon steel via fast induction heating quenching & tempering10.1016/j.jmrt.2023.05.260 ↗
92. Microstructural evolution of secondary carbides during spheroidized annealing and quenching and tempering in 60Cr16MoMA martensitic stainless steel10.1016/j.jmrt.2023.12.264 ↗
93. Investigation of microstructural effects on electrical resistivity and their implications for eddy current methods in measuring residual stresses in IN718