Role of initial microstructures in governing austenite reversion kinetics and morphology in medium manganese steel
Source abstract
Abstract
The influence of two distinct initial microstructures, fully martensitic (M) and bainitic ferrite with retained austenite (BF+RA), on austenite reversion kinetics and microstructural evolution was systematically examined in a Fe–0.19C–4.03Mn–1.48Si medium-manganese steel. These microstructures were obtained through direct quenching and austempering, respectively, followed by intercritical annealing. During annealing at 943 K, the BF+RA microstructure attained the equilibrium austenite fraction within 1 hour, whereas the M microstructure required approximately 3 hours, indicating significantly accelerated austenite reversion kinetics in the BF+RA condition. At equilibrium, the M microstructure contained 16.7% globular austenite and 23.5% acicular austenite, while the BF+RA microstructure exhibited a lower fraction of globular austenite (7.8%) but a substantially higher fraction of acicular austenite (35.4%). Similar trends were observed during annealing at 963 K. Theoretical analysis suggests that coarse cementite particles serve as preferential nucleation sites for globular austenite; therefore, carbide coarsening during intercritical annealing promotes globular austenite formation. In contrast, in the BF+RA initial microstructure, pre-existing austenite suppresses cementite precipitation prior to reversion, thereby inhibiting globular austenite development. Experimental observations combined with thermodynamic calculations further demonstrate that pre-existing austenite provides energetically favorable growth sites during recovery, eliminating the requirement for new nucleation events and significantly accelerating the early stages of austenite reversion. Additionally, manganese enrichment within carbides was more pronounced in the M microstructure than in the BF+RA microstructure, resulting in stronger solute drag effects on austenite nucleation and growth and consequently contributing to the comparatively slower reversion kinetics observed in the martensitic condition.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Heterostructure mediated high strength and large ductility in novel medium-Mn steels with low Mn content10.1016/j.actamat.2024.120092 ↗
2. Acceleration of retained austenite formation and elemental partitioning by control of pre-existed austenite morphology in medium Mn steel10.1016/j.actamat.2025.121208 ↗
3. Simultaneous improvement in load-bearing capacity and energy absorption of resistance spot-welded medium Mn steel: an integrated simulation and experimental approach10.1007/s11661-025-07748-x ↗
4. A review of the thermal stability of metastable austenite in steels: martensite formation10.1016/j.jmst.2021.03.020 ↗
5. Physical metallurgy-guided machine learning and artificial intelligent design of ultrahigh-strength stainless steel10.1016/j.actamat.2019.08.033 ↗
6. Synergizing TWIP and TRIP effects for optimized mechanical performance via stacking fault energy control in austenitic steels10.1007/s43452-025-01333-0 ↗
7. Strain rate induced TRIP/TWIP effects and damage initiation in a novel Fe-Mn-Al-Nb medium manganese steel: experiments and modeling10.1016/j.msea.2025.148209 ↗
8. Time-dependent evolution of volume fraction and stability of retained austenite in a hot-rolled and intercritically annealed Al-Alloyed Medium-Mn steel10.1007/s11661-023-06998-x ↗
9. Understanding the TRIP effect in hot- and cold-rolled Al-added medium-Mn steels: insights into austenite stability and martensitic transformation kinetics
10. Mechanical failure of CrN/Cu/CrN interfacial regions under tensile loading10.1016/j.actamat.2018.08.046 ↗
11. Effect of pre-existed austenite on austenite reversion and mechanical behavior of an Fe-0.2C-8Mn-2Al medium Mn steel10.1016/j.actamat.2018.01.009 ↗
12. Influence of heating rate on the evolution of post-annealed microstructure in Nb–Ti microalloyed steel: interplay with initial cold-rolled microstructure10.1016/j.jmrt.2024.11.168 ↗
13. Effect of intercritical annealing on the Lüders strains of medium Mn transformation-induced plasticity steels10.1016/j.matdes.2015.05.085 ↗
14. Precipitation and reverted austenite formation in maraging 350 steel: competition or cooperation?10.1016/j.actamat.2024.119865 ↗
15. Tailoring the microstructure by prior treatment to achieve 37.6 GPa·% PSE in a room-temperature quenched and partitioned steel
16. Hot rolled and cold rolled medium manganese steel: mechanical properties and microstructure10.1016/j.msea.2017.06.088 ↗
17. Revealing the interdependence of microstructure evolution, micromechanics and macroscopic mechanical behavior of multi-phase medium Mn steels10.1016/j.msea.2022.142857 ↗
18. Austenite nucleation and growth as a function of starting microstructure for a Fe–0.15C–5.56Mn–1.1Si–1.89Al Medium-Mn steel10.1002/srin.202200952 ↗
19. Role of cementite and retained austenite on austenite reversion from martensite and bainite in Fe-2Mn-1.5Si-0.3C alloy
20. Exploring microstructural design and deformation mechanisms in TRIP-assisted steels with diverse martensitic-type start microstructure10.1016/j.matchar.2025.115338 ↗
21. Microstructure evolution and strain behavior of a medium Mn TRIP/TWIP steel for excellent combination of strength and ductility10.1016/j.msea.2019.03.021 ↗
22. Influence of initial microstructure on reaustenitization behavior in low alloy steel by in-situ high-temperature EBSD characterization10.1016/j.matlet.2023.134876 ↗
23. Contribution of grain boundary misorientation to intragranular globular austenite reversion and resultant in grain refinement in a high-strength low-alloy steel10.1016/j.matchar.2020.110634 ↗
24. Microstructural evolution during cold rolling and subsequent annealing in low-carbon steel with different initial microstructures10.1007/s11665-017-2849-6 ↗
25. Orientation of austenite reverted from martensite in Fe-2Mn-1.5Si-0.3C alloy10.1016/j.actamat.2017.11.003 ↗
26. Effect of Mn content on the toughness and plasticity of hot-rolled high-carbon medium manganese steel10.3390/ma16062299 ↗
27. Effect of Mn on the chemical driving force and bainite transformation kinetics in medium-manganese alloys10.1007/s10973-022-11664-2 ↗
28. Influence of Mn on nanobainite formation kinetics and austenite retention in Al-added medium-Mn steels subjected to hybrid isothermal annealing10.1016/j.jmrt.2025.05.256 ↗
29. Effect of starting microstructures on the reverse transformation kinetics in low-carbon steel10.3390/met10121601 ↗
30. Austenite stabilization through manganese enrichment10.1016/j.scriptamat.2010.09.040 ↗
31. Effect of two-step bainite treatment on the morphology and texture of retained austenite and mechanical properties of austenitizing pretreated transformation-induced plasticity steel10.1016/j.msea.2019.138567 ↗
32. Effects of prior austenite grain size on reversion kinetics of different crystallographic austenite in a low carbon steel10.1016/j.matchar.2022.112025 ↗
33. Impact of intercritical annealing temperature and strain state on mechanical stability of retained austenite in medium Mn steel10.1016/j.msea.2018.04.041 ↗
34. Thermal stability of retained austenite in TRIP steels studied by synchrotron X-ray diffraction during cooling10.1016/j.actamat.2005.08.017 ↗
35. Study of the isothermal bainitic transformation and austenite stability in an advanced Al-rich medium-Mn steel10.1007/s43452-022-00475-9 ↗
36. Effect of intercritical annealing time on hydrogen embrittlement of warm-rolled medium Mn steel10.1016/j.msea.2018.04.100 ↗
37. Crucial microstructural feature to determine the impact toughness of intercritically annealed medium-Mn steel with triplex-phase microstructure10.1016/j.actamat.2018.10.043 ↗
38. Effect of hot deformation on bainitic transformation and retained austenite in a 3Mn medium Mn steel
39. Porter · 1992 · 271
40. Thermodynamics and kinetics of martensitic transformations10.1016/0502-8205(58)90005-4 ↗
41. Phase transformations in metals and alloys
42. Growth mode of austenite during reversion from martensite in Fe-2Mn-1.5Si-0.3C alloy: a transition in kinetics and morphology10.1016/j.actamat.2018.05.035 ↗
43. Austenite memory during reverse transformation of steels at different heating rates
44. Simulation of the growth of austenite from As-Quenched martensite in medium Mn steels
45. Accelerated ferrite-to-austenite transformation during intercritical annealing of medium-manganese steels due to cold-rolling10.3390/met9090926 ↗
46. Interaction of alloying elements with migrating Ferrite/Austenite interface:transformations and microstructures10.2355/isijinternational.ISIJINT-2020-216 ↗
47. Interaction of solute impurity with grain boundary: the impurity drag effect10.1023/A:1015186905631 ↗
48. A treatment of the solute drag on moving grain boundaries and phase interfaces in binary alloys10.1016/0001-6160(76)90108-5 ↗
49. Modelling the austenite to ferrite phase transformation in low carbon steels in terms of the interface mobility10.2355/isijinternational.40.713 ↗
50. Austenite-to-ferrite phase transformation in low-alloyed steels10.1016/j.commatsci.2004.09.031 ↗
51. A concise derivation of the contact conditions at a migrating sharp interface10.1080/09500830802039921 ↗
52. A ten-year history of discussions of alloying-element interactions with migrating interfaces10.1007/s11661-011-0766-0 ↗
53. Chemical gradients across phase boundaries between martensite and austenite in steel studied by atom probe tomography and simulation10.1016/j.actamat.2010.09.042 ↗
54. Austenite formation and cementite dissolution during intercritical annealing of a medium-manganese steel from a martensitic condition10.1016/j.matdes.2021.109598 ↗