Multi-walled carbon nanotubes reinforced Inconel 718 superalloy fabricated by spark plasma sintering: Microstructure and mechanical property
Source abstract
Abstract
To investigate the densification and strengthening mechanisms of MWCNT/Inconel 718 composites, samples with different MWCNTs content are fabricated by spark plasma sintering (SPS) at varying sintering temperatures. The densification process, the room-temperature flexural and compression properties, the mechanical properties at high temperatures, and microstructure evolution are discussed. Increasing the sintering temperature improves material densification by reducing the number of indented pores and gully defects in the heating and holding stage. The incorporation of MWCNTs, though impeding material density by affecting the bonding of powder particles, can enhance the mechanical properties of the composites through load transfer and Orowan strengthening mechanisms. The composites prepared at 1050 °C with 0.5% MWCNTs content show a high relative density of 97%, a flexural strength of 1090 MPa, a compressive strength of 1523 MPa, and a high-temperature (1200 K) compression strength of 138.5 MPa, which are all much higher than that of Inconel 718 alloy. Finally, turbine blades with complex curved areas are prepared at a temperature of 1050 °C and an MWCNTs content of 0.5%, providing a new idea for forming high-strength superalloy matrix composites that can withstand ultra-high temperatures.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (70)
Show source-provided references
1. Effect of tio2 content on the thermal control properties of al2o3-xtio2 composite coatings prepared by supersonic plasma spraying technology10.1016/j.jmrt.2024.08.199 ↗
2. Waterborne robust superhydrophobic pfdtes@tio2-pu coating with stable corrosion resistance, long-term environmental adaptability, and delayed icing functions on al–li alloy10.1016/j.jmrt.2024.08.131 ↗
3. Mechanical response and wear behavior of graphene reinforced inconel 718 composite produced via hybrid accumulative roll bonding and gas tungsten arc welding process10.1016/j.jmrt.2022.06.013 ↗
4. Intermetallic regulation mechanism of inconel 718/ti6al4v composite by novel follow-up ultrasonic assisted laser additive manufacturing10.1016/j.compositesb.2022.109736 ↗
5. Effect of γ'-δ precipitates tailored by ti3alc2 on inconel 718 composites: microstructure evolution, enhanced properties and strengthening mechanism10.1016/j.matchar.2023.113191 ↗
6. Microstructures, mechanical properties, and oxidation behavior of in-situ ultra-fine duplex carbides reinforced ni-based superalloy composites10.1016/j.jallcom.2023.171321 ↗
7. Thermal properties of inconel 625-nbc metal matrix composites (mmc)10.1016/j.matdes.2022.111399 ↗
8. Additive manufacturing of high-strength inconel 718 alloy through the addition of ti2alc max particles10.1016/j.jmst.2023.01.059 ↗
9. A concentrated-flux-type pm machine with irregular magnets and iron poles
10. Development of a novel radial-flux machine with enhanced torque profile employing quasi-cylindrical pm pattern
11. The microstructure evolution and precipitation behavior of tib2/inconel 718 composites manufactured by selective laser melting10.1016/j.jmapro.2022.04.070 ↗
12. Size effect on the cyclic deformation behavior of superalloy ultrathin sheet: characterization and multiscale modelling10.1016/j.ijplas.2023.103566 ↗
13. Pulse current enhanced densification and mechanical property of inconel 718 superalloy fabricated by spark plasma sintering10.1016/j.msea.2024.147061 ↗
14. Investigation on the biaxial tensile testing method for metal foil using cruciform specimen10.1016/j.tafmec.2024.104577 ↗
15. A global springback compensation method for manufacturing metallic seal ring with complex cross-section and submillimeter precision10.1016/j.jmatprotec.2024.118498 ↗
16. Effect of mwcnt/nanosilica reinforcement on the mechanical and thermal behaviour of polymer composite10.1016/j.matpr.2022.04.1015 ↗
17. Al-mwcnt nanocomposite synthesized via spark plasma sintering: effect of powder milling and reinforcement addition on sintering kinetics and mechanical properties10.1016/j.jmrt.2018.03.005 ↗
18. Wear behaviour of al-mwcnt composites by varying mwcnts concentration10.1016/j.jalmes.2024.100104 ↗
19. Effect of dry milling and mwcnts content during fabrication of fe-mwcnts metal matrix composite by high energy planetary milling followed by conventional sintering10.1016/j.apt.2022.103447 ↗
20. Microstructural characteristics and mechanical properties of carbon nanotube reinforced inconel 625 parts fabricated by selective laser melting10.1016/j.matdes.2016.09.080 ↗
21. Micro-structure and mechanical properties of nano-tic reinforced inconel 625 deposited using laam10.1016/j.phpro.2013.03.155 ↗
22. Ti3sic2 reinforced inconel 625 composites prepared via laser directed energy deposition: new insights into microstructure evolution and mechanical properties10.1016/j.jallcom.2023.172396 ↗
23. Laser powder deposition of carbon nanotube reinforced nickel-based superalloy inconel 71810.1016/j.carbon.2016.06.014 ↗
24. Strengthening additively manufactured inconel 718 through in-situ formation of nanocarbides and silicides
25. Effects of cnts on microstructure and hardness of laser welds of the cnt-reinforced magnesium composite10.1016/j.compositesa.2013.01.013 ↗
26. Fabrication of aluminum/stainless steel bimetallic composites through a combination of additive manufacturing and vacuum-assisted melt infiltration casting10.1016/j.jmapro.2021.07.047 ↗
27. Effects of cr and al contents on the preparation of sic fiber-reinforced nicral alloy matrix composite10.1007/s40195-020-01024-0 ↗
28. E-waste crt panel glass reinforced magnesium composite processed through powder metallurgy: fabrication and mechanical performance evaluation10.1016/j.jmrt.2023.10.178 ↗
29. Microstructure and mechanical properties of ti-tibw-x%cu composites by powder metallurgy using atomized ti-tibw powder as raw materials10.1016/j.vacuum.2023.112521 ↗
30. Effect of powder size segregation on the mechanical properties of hot isostatic pressing inconel 718 alloys10.1016/j.jmrt.2022.09.009 ↗
31. Energy field assisted metal forming: current status, challenges and prospects10.1016/j.ijmachtools.2023.104075 ↗
32. Electrically assisted manufacturing of microchannels with enhanced filling quality and microstructural performance for thermal management10.1016/j.ijheatmasstransfer.2022.123774 ↗
33. Effect of grain size on superplastic deformation behavior of zn-0.033 mg alloy10.1016/j.msea.2023.144877 ↗
34. Novel approach of the evaluation of electric current density during the spark plasma sintering: effect on the densification mechanisms of b4c-based ceramics10.1016/j.ijrmhm.2021.105703 ↗
35. Effect of heating rate on microstructure and mechanical properties of alcocrfeni high entropy alloy produced by spark plasma sintering10.1016/j.matchar.2019.05.022 ↗
36. Preparation and toughness mechanism of in-situ ti3alc2 enhanced and toughened tial3 matrix composites10.1016/j.intermet.2023.107963 ↗
37. Effect of mechanical alloying on microstructure and mechanical properties of ti-24nb-4zr-3mn alloys prepared by spark plasma sintering10.1016/j.jallcom.2022.167023 ↗
38. Effects of temperature on microstructure and mechanical properties of in718 reinforced by reduced graphene oxide through spark plasma sintering10.1016/j.jallcom.2018.07.071 ↗
39. Characterization of ni–cnts nanocomposites produced by ball-milling10.3390/met10010002 ↗
40. Mechanical, morphological, and fracture-deformation behavior of mwcnts-reinforced (al–cu–mg–t351) alloy cast nanocomposites fabricated by optimized mechanical milling and powder metallurgy techniques10.1515/ntrev-2022-0005 ↗
41. Study on the effect of multi-walled carbon nanotube (mwcnt) addition on the microstructure, mechanical and cutting performance of silicon nitride ceramic tools10.1016/j.ijrmhm.2024.106907 ↗
42. Effect of sintering temperature on microstructure and mechanical properties of inconel 718 superalloy prepared by micro-fast10.1016/j.msea.2022.142733 ↗
43. Effect of sintering duration on microstructure and properties of inconel 718 superalloy prepared by electric field-activated sintering10.1016/j.jmapro.2023.09.031 ↗
44. Controlling grain size via dynamic recrystallization in an advanced polycrystalline nickel base superalloy10.1016/j.jallcom.2017.01.179 ↗
45. Ebsd study of grain growth behavior and annealing twin evolution after full recrystallization in a nickel-based superalloy10.1016/j.jallcom.2017.07.027 ↗
46. Strengthening and toughening effects of mwcnts on si2bc3n ceramics sintered by sps technique10.1016/j.msea.2017.10.089 ↗
47. Microstructure, properties and toughening mechanisms of mosi2@zro2 core shell composites prepared by spark plasma sintering10.1016/j.matchar.2022.112510 ↗
48. A 2d and 3d segmentation-based microstructure study on the role of brittle phases in diffusion brazed aisi 304l/nicrsifemob joints10.1016/j.matdes.2023.112401 ↗
49. Effect of solution heat treatment on the precipitation behavior and strengthening mechanisms of electron beam smelted inconel 718 superalloy10.1016/j.msea.2017.01.093 ↗
50. The heterogeneous microstructure in laser powder bed fabricated inconel 718 pillar and its influence on mechanical properties10.1016/j.msea.2023.144953 ↗
51. Consideration of particle rearrangement during the modeling of spark plasma densification of al–mg alloy powders10.1016/j.scriptamat.2015.01.003 ↗
52. Enhanced particle rearrangement during liquid phase spark plasma sintering of silicon nitride-based ceramics10.1016/j.ceramint.2010.08.019 ↗
53. Densification mechanisms in spark plasma sintering: effect of particle size and pressure10.1016/j.powtec.2012.01.005 ↗
54. Microstructure and properties of nial/tic composite synthesized by spark plasma sintering of mechanically activated elemental powders10.1016/j.ceramint.2023.01.163 ↗
55. A review of multi-physical fields induced phenomena and effects in spark plasma sintering: fundamentals and applications10.1016/j.matdes.2020.108662 ↗
56. Effect of sintering duration on microstructure and properties of inconel 718 superalloy prepared by electric field-activated sintering10.1016/j.jmapro.2023.09.031 ↗
57. Improved strength and conductivity of metallic-glass-reinforced nanocrystalline cucrzr alloy10.1016/j.matdes.2022.110420 ↗
58. Effect of in-situ formed oxide and carbide phases on microstructure and corrosion behavior of zr/y doped cocrfeni high entropy alloys prepared by mechanical alloying and spark plasma sintering10.1016/j.intermet.2023.107998 ↗
59. Particle-reinforced metal matrix nanocomposites fabricated by selective laser melting: a state of the art review10.1016/j.pmatsci.2019.04.006 ↗
60. Achieving excellent uniform tensile ductility and strength in dislocation-cell-structured high-entropy alloys10.1016/j.ijplas.2024.104079 ↗
61. Y2o3 nanoparticles decorated in738lc superalloy manufactured by laser powder bed fusion: cracking inhibition, microstructures and mechanical properties10.1016/j.compositesb.2021.109555 ↗
62. Strengthening mechanisms in polycrystalline multimodal nickel-base superalloys. Metallurgical and materials transactions
63. Graphene-strengthened inconel 625 alloy fabricated by selective laser melting10.1016/j.msea.2020.140099 ↗
64. Effect of interfacial bridging atoms on the strength of al/cnt composites: machine-learning-based prediction and experimental validation10.1016/j.jmrt.2022.01.092 ↗
65. Novel tib2-reinforced 316l stainless steel nanocomposites with excellent room- and high-temperature yield strength developed by additive manufacturing10.1016/j.compositesb.2018.07.050 ↗
66. Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of hall–petch effect10.1016/j.msea.2011.10.043 ↗
67. Microstructure and mechanical properties of tin particles strengthened 316l steel prepared by laser melting deposition process10.1016/j.msea.2021.141220 ↗
68. Strengthening mechanisms in a high-strength bulk nanostructured cu–zn–al alloy processed via cryomilling and spark plasma sintering10.1016/j.actamat.2012.09.036 ↗
69. High temperature thermal physical performance of beo/uo2 composites prepared by spark plasma sintering (sps)10.1016/j.scriptamat.2017.08.031 ↗
70. Spark plasma sintering and complex shapes: the deformed interfaces approach10.1016/j.powtec.2017.07.048 ↗