Microstructure and tensile properties of transient liquid phase (TLP) sintering repaired Ti–6Al–4V alloys with large area hole defect
Source abstract
Abstract
Repairing defects in titanium alloy components is economically justified due to their high cost. In this work, Ti–6Al–4V samples with large area hole defects are repaired by transient liquid-phase sintering. The microstructure and tensile properties after repair have been investigated. The factors of different base powder morphology and the ratio of braze metal are also studied. The results show that by using spherical Ti64 alloy powder with 40 wt% TiZrCuNi braze alloy powder, an overall repair effect with high-density repair zone and good interface combination can be obtained at 960 °C for 3 h. The tensile strength of the as-repaired exceeds that of the matrix, but the elongation is lower than that of the matrix. Finally, the repair experiment conducted at various angles demonstrates this technique's strong practical feasibility.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Titanium Alloys Microstructure and Properties · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Progress in structural materials for aerospace systems10.1016/j.actamat.2003.08.023 ↗
2. Thresholds for high-cycle fatigue in a turbine engine Ti–6Al–4V alloy10.1016/S0142-1123(99)00024-9 ↗
3. Advances in investment casting of Ti–6Al–4V alloy: a review10.1179/136404605225023225 ↗
4. Effect of weld repair on microstructure and mechanical properties of laser additive manufactured Ti-55511 alloy10.1016/j.matdes.2017.01.054 ↗
5. Analysis of weld-cracking and improvement of the weld-repair process of superplastic forming tools10.1016/j.matdes.2012.11.003 ↗
6. Parameter optimization of gas tungsten-arc repair welding technique in Mg-6Gd-3Y-0.5Zr alloy10.1007/s40962-018-0257-9 ↗
7. Microstructure and properties of Al6Cu2Ni gearbox with TIG additive for repairing casting defects
8. Investigating the effects of repair welding on microstructure, mechanical properties, and corrosion behavior of IN-939 superalloy10.1007/s11665-022-07596-5 ↗
9. A novel perception toward welding of stainless steel by activated TIG welding: a review10.1080/10426914.2020.1854467 ↗
10. Microstructural characteristics and mechanical properties of repaired titanium alloy blade by arc additive manufacturing process10.1002/adem.202000187 ↗
11. TC17 titanium alloy laser melting deposition repair process and properties10.1016/j.optlastec.2016.02.013 ↗
12. Titanium alloy repair with wire-feed electron beam additive manufacturing technology
13. Reconditioning gas turbine blisks by electron beam welding a repair insert10.1080/09507116.2014.911423 ↗
14. Microstructure and mechanical properties of laser additive repaired Ti17 titanium alloy10.1016/S1003-6326(17)60289-9 ↗
15. Effects of thermal undercooling and thermal cycles on the grain and microstructure evolution of TC17 titanium alloy repaired by wire arc additive manufacturing10.1007/s00170-021-08445-w ↗
16. Gas tungsten arc welding of α + β titanium alloys: a review
17. Effect of the formation process of transient liquid phase (TLP) on the interface structure of TiAl joints
18. Additive manufacturing of titanium alloys by electron beam melting: a review10.1002/adem.201700842 ↗
19. Microstructure and tensile properties of nickel-based superalloy K417G bonded using transient liquid-phase infiltration10.1016/j.matdes.2013.04.024 ↗
20. Investigation on microstructural properties of transient liquid phase (TLP) bonded IN-738LC superalloy with AMS 4776 filler metal10.1179/1743284712Y.0000000138 ↗
21. Microstructure and mechanical response of transient liquid phase joint in Haynes 282 superalloy10.1016/j.matchar.2010.09.011 ↗
22. Stiffer bonding of armchair edge in single-layer molybdenum disulfide nanoribbons
23. Yan G, Bhowmik A, Nagarajan B, Song X,Tan MJ. Post-bond heat treatment effects on the wide gap transient liquid phase bonding of Inconel 718 with BNi-2 paste filler metal. Mater Sci Eng, A 766:https://doi.org/10.1016/j.msea.2019.138267.10.1016/j.msea.2019.138267 ↗
24. Vacuum TLP bonding of Inconel 617 superalloy using Ni-Cr-Si-Fe-B filler metal: metallurgical structure and mechanical properties10.1016/j.vacuum.2018.03.048 ↗
25. TLP repaired IN738LC superalloy with uneven surface defect gap width after post heat treatment: microstructure and mechanical properties10.1016/j.jallcom.2018.02.343 ↗
26. Review: liquid phase sintering10.1007/s10853-008-3008-0 ↗
27. Metal injection moulding of titanium and titanium alloys: challenges and recent development10.1016/j.powtec.2017.06.053 ↗
28. Metal injection moulding of non-spherical titanium powders: processing, microstructure and mechanical properties10.1016/j.jmapro.2017.12.004 ↗
29. Morphological evolution of transformation products and eutectoid transformation(s) in a hyper-eutectoid Ti-12 at% Cu alloy10.1016/j.actamat.2019.01.044 ↗
30. Effects of pure Ti or Zr powder on microstructure and mechanical properties of Ti6Al4V and Ti2AlNb joints brazed with TiZrCuNi10.1016/j.msea.2020.139602 ↗
31. Design TiZrCuNi filler materials for vacuum brazing TA15 alloy10.1016/j.jmapro.2020.02.021 ↗
32. The influence of Zr content on the performance of TiZrCuNi brazing filler10.1016/j.msea.2016.09.115 ↗
33. Diffusion of copper in beta-titanium
34. Diffusion of solute elements in beta-titanium10.1016/0001-6160(62)90057-3 ↗
35. Pressure dependence of anomalous diffusion of zirconium in β-Titanium10.1007/BF02651930 ↗
36. A comparison of Ti–Ni and Ti-Sn binary alloys processed using powder metallurgy10.1016/j.msea.2015.07.085 ↗
37. Microstructural evolution and shear strength of brazing C103 and Ti–6Al–4V using Ti–20Cu–20Ni–20Zr (wt.%) filler metal10.1016/j.ijrmhm.2005.05.014 ↗
38. Infrared brazing of TiAl intermetallic using BAg-8 braze alloy10.1016/S1359-6454(02)00606-7 ↗
39. Cavitation erosion mechanism of NiTi coatings made by laser plasma hybrid spraying10.1016/S0043-1648(99)00133-7 ↗
40. Titanium sintering science: a review of atomic events during densification10.1016/j.ijrmhm.2020.105214 ↗