Analysis and simulation research on deep drawing of magnesium alloy box-shaped products with sand die based on different driving modes
Source abstract
Abstract
Deep drawing of box-shaped products is of wide interest. In this study, sand was used as a flexible medium to replace the rigid die for deep drawing of box-shaped products. This method can enable forming with reduced die cost. During the deep drawing, three driving modes were realized through different placement of the sand. To study the difference among these three driving modes, the macroscopic and microscopic cooperative verification method was adopted. At the macroscopic level, the pressure stress was analyzed by using analytical models and simulation. The stress variation rules were also obtained. At the microscopic level, the microstructure of the key regions is discussed. The results show that the maximum decrease in the average grain size was about 82.38%. The maximum proportion of deformed grains was about 4.30%. The rules governing the change in the microstructure and stress were obtained, enabling prediction of the stress distribution and the microstructure of other products obtained by using sand forming.Graphical abstract
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. L. Giorleo, E. Ceretti, Deep drawing punches produced using fused filament fabrication technology: performance evaluation. J. Manuf. Process. 84, 1–9 (2022). https://doi.org/10.1016/j.jmapro.2022.09.05410.1016/j.jmapro.2022.09.054 ↗
2. S.H. Li, Sheet metal deep drawing for making metallic parts and structures. In: Encyclopedia of Materials: Metals and Alloys (2022), pp. 182–196. https://doi.org/10.1016/B978-0-12-819726-4.00011-910.1016/B978-0-12-819726-4.00011-9 ↗
3. V.M. Brathikan, N. Sangeetha, B. Sangeethkumar, K. Scidarth, Influence of various blank diameter in deep drawing. Procedia Manuf. 68, 1995–1999 (2022). https://doi.org/10.1016/j.matpr.2022.08.28110.1016/j.matpr.2022.08.281 ↗
4. Z.H. Mahmood, I.K. Irthiea, A.K. Ahmed, Optimization of initial blank shape for flexible micro deep drawing of square parts. Mater Today Proc. 20, 555–559 (2020). https://doi.org/10.1016/j.matpr.2019.09.18810.1016/j.matpr.2019.09.188 ↗
5. M.Y. Cao, C.C. Zhao, G.J. Dong, S.F. Yang, Instability analysis of free deformation zone of cylindrical parts based on hot-granule medium-pressure forming technology. Trans. Nonferr. Met. Soc. China 28, 2188–2196 (2016). https://doi.org/10.1016/S1003-6326(16)64335-210.1016/S1003-6326(16)64335-2 ↗
6. F.F. Zhang, Y.N. Wei, K. He, Z.Q. Hang, Experimental investigation on electro-hydraulic forming with flexible-die. Procedia Manuf. 50, 324–327 (2020). https://doi.org/10.1016/j.promfg.2020.08.06010.1016/j.promfg.2020.08.060 ↗
7. P.Y. Wang, Z.J. Wang, N. Xiang, Z.X. Li, Investigation on changing loading path in sheet metal forming by applying a property-adjustable flexible-die. J. Manuf. Process. 53, 364–375 (2020). https://doi.org/10.1016/j.jmapro.2020.03.03310.1016/j.jmapro.2020.03.033 ↗
8. R. Gitschel, F. Kolpak, O. Hering, A.E. Tekkaya, Increasing the lightweight potential of composite cold forging by utilizing magnesium and granular cores. Metals (2021). https://doi.org/10.3390/met1101003210.3390/met11010032 ↗
9. A. Leonhardt, G. Kurz, J. Victoria-Hernández, V. Kräusel, D. Landgrebe, D. Letzig, Experimental study on incremental sheet forming of magnesium alloy AZ31 with hot air heating. Procedia Manuf. 15, 1192–1199 (2018). https://doi.org/10.1016/j.promfg.2018.07.36910.1016/j.promfg.2018.07.369 ↗
10. T.F. Kong, X.Z. Lu, L.C. Chan, Analysis and reduction of wrinkling defects for tube-hydroforming magnesium alloy components at elevated temperatures. Mater. Des. (2019). https://doi.org/10.1016/j.matdes.2019.10776110.1016/j.matdes.2019.107761 ↗
11. S.V. Raut, A. Ramesh, A. Arun, C.S. Sumesh, Finite element analysis and optimization of tube hydroforming process. Mater. Today Proc. 46, 5008–5016 (2021). https://doi.org/10.1016/j.matpr.2020.10.39410.1016/j.matpr.2020.10.394 ↗
12. Z.J. Wang, P.Y. Wang, H. Song, Research on sheet-metal flexible-die forming using a magnetorheological fluid. J. Mater. Process. Technol. 214, 2200–2211 (2014). https://doi.org/10.1016/j.jmatprotec.2014.04.01610.1016/j.jmatprotec.2014.04.016 ↗
13. J. Bi, C.C. Zhao, B. Du, Q.B. Guo, G.J. Dong, Formability and strengthening mechanism of AA6061 tubular components under solid granule medium internal high pressure forming. Trans. Nonferr. Met. Soc. China 28, 226–234 (2018). https://doi.org/10.1016/S1003-6326(18)64655-210.1016/S1003-6326(18)64655-2 ↗
14. M.Y. Cao, Y.X. Peng, C.C. Zhao, G.J. Dong, B. Du, Frictional characteristics of granular system under high pressure. J. Cent. South Univ. 23, 1132–1141 (2016). https://doi.org/10.1007/s11771-016-0363-x10.1007/s11771-016-0363-x ↗
15. Q.L. Wang, R. Bertolini, S. Bruschi, A. Ghiotti, Anisotropic fracture behavior of AZ31 magnesium alloy sheets as a function of the stress state and temperature. Int. J. Mech. Sci. (2019). https://doi.org/10.1016/S1003-6326(12)61739-710.1016/S1003-6326(12)61739-7 ↗
16. Z.H. Li, G.W. Zhou, D.Y. Li, M.K. Jain, Y.H. Peng, Wu PD, Forming limits of magnesium alloy AZ31B sheet at elevated temperatures. Int. J. Plast. (2020). https://doi.org/10.1016/j.ijplas.2020.10282210.1016/j.ijplas.2020.102822 ↗
17. N. Guo, J. Wang, C.Y. Sun, Y.F. Zhang, M.W. Fu, Analysis of size dependent earing evolution in micro deep drawing of TWIP steel by using crystal plasticity modeling. Int. J. Mech. Sci. (2020). https://doi.org/10.1016/j.ijmecsci.2019.10520010.1016/j.ijmecsci.2019.105200 ↗
18. P.Y. Wang, G.H. Wan, J.G. Jin, Y.C. Wang, N. Xiang, X.K. Zhao et al., Subregional flexible-die control in magnetorheological pressure forming. J. Mater. Process. Technol. (2022). https://doi.org/10.1016/j.jmatprotec.2022.11769810.1016/j.jmatprotec.2022.117698 ↗
19. F. Faramarz, Y. Saeed, Textural and microstructural analyses and ranking of the process parameters in hydro-mechanical deep drawing of AZ31B magnesium sheets. J. Mater. Res. Technol. 24, 9261–9272 (2023). https://doi.org/10.1016/j.jmrt.2023.05.12610.1016/j.jmrt.2023.05.126 ↗
20. W.C. Liu, J. Huang, Y. Pang, K. Zhu, S.G. Li, J. Ma, Multi-scale modelling of evolving plastic anisotropy during Al-alloy sheet forming. Int. J. Mech. Sci. (2023). https://doi.org/10.1016/j.ijmecsci.2023.10816810.1016/j.ijmecsci.2023.108168 ↗
21. G.S. Cai, J.L. Yang, Y.F. Yuan, X.Y. Yang, L.H. Lang, Alexandrov S, Mechanics analysis of aluminum alloy cylindrical cup during warm sheet hydromechanical deep drawing. Int. J. Mech. Sci. (2020). https://doi.org/10.1016/j.ijmecsci.2020.10555610.1016/j.ijmecsci.2020.105556 ↗
22. N. Xu, P.L. Mao, L. Zhou, Z. Wang, F. Wang, Z. Liu et al., Effect of pre-strain on extension twinning behavior in an extruded AZ31 Mg alloy observed by in situ EBSD. Mater. Charact. (2023). https://doi.org/10.1016/j.matchar.2023.11289310.1016/j.matchar.2023.112893 ↗
23. P. Peng, D.L. Yu, X.M. Guo, P. Zhang, S.N. Chai, Q.W. Dai et al., Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling. J. Mater. Res. Technol. 26, 1293–1305 (2023). https://doi.org/10.1016/j.jmrt.2023.07.21010.1016/j.jmrt.2023.07.210 ↗
24. Y.Z. Zhu, D.W. Hou, Q.Z. Li, Quasi in situ EBSD analysis of twinning–detwinning and slip behaviors in textured AZ31 magnesium alloy subjected to compressive-tensile loading. J. Magnes. Alloy 10, 956–964 (2022). https://doi.org/10.1016/j.jma.2021.08.02510.1016/j.jma.2021.08.025 ↗
25. W.H. Chen, W.J. He, B. Jiang, F.S. Pan, Simultaneous enhancement of strength and ductility for AZ31 magnesium alloy by pre-twinning induced heterostructure. Int. J. Plast. (2022). https://doi.org/10.1016/j.ijplas.2022.10348310.1016/j.ijplas.2022.103483 ↗
26. J.J. Fan, H.H. Lu, W.G. Zhang, W. Liang, Analysis on anisotropy of mechanical properties of bimodal texture type AZ31 magnesium alloy plate. J. Netshape Form. Eng. 15(8), 10–18 (2023)
27. S.N. Shi, H.Y. Wang, F. Teng, L. Jiang, J.C. Sun, J. Sun, S.H. Zhang, Experimental and simulation research on hollow AZ31 magnesium alloy three-channel joint by hot extrusion forming with sand mandrel. J. Magnes. Alloy (2022). https://doi.org/10.1016/j.jma.2022.01.01210.1016/j.jma.2022.01.012 ↗
28. G.J. Dong, C.C. Zhao, M.Y. Cao, Flexible-die forming process with solid granule medium on sheet metal. Trans. Nonferr. Met. Soc. China 023, 2666–2677 (2013). https://doi.org/10.1016/S1003-6326(13)62783-110.1016/S1003-6326(13)62783-1 ↗
29. T.Y. Shen, H. Liu, J.L. Zhang, M. Ma, Z.Q. Wu, L.F. Liu et al., The improvement on mechanical anisotropy of AZ31 magnesium alloy sheets by multi cross-rolling process. J. Alloys Compd. (2023). https://doi.org/10.1016/j.jallcom.2023.17125210.1016/j.jallcom.2023.171252 ↗