New Design Methodology for Seismic Column-to-Foundation Anchorage Connections
Source abstract
Abstract
Earlier studies have shown that post-installed reinforcing bars are capable of developing bond behavior equivalent to cast-inplace reinforcing bars. Therefore, connections with post-installed starter bars using qualified adhesives can be designed according to conventional anchorage design provisions. However, this approach often results in development lengths which cannot be accommodated in structural joints without hooks due to the limited thickness of members. The results of 16 full-scale tests presented in this paper show the beneficial effect of increased bond strengths due to column moment loading and the adverse effect of reduced bond strengths due to cyclic loading on the seismic performance of column-to-foundation connections. The quantification of both effects is a prerequisite for the development of a new design methodology for these joints, which are based on current bonded anchor design provisions. The proposed design approach potentially allows a reduction of the development length to the extent that hooks may not be required.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis · Structural Response to Dynamic Loads
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. ACI Committee 318, “Building Code Requirements for Structural Concrete (ACI 318-11) and Commentary,” American Concrete Institute, Farmington Hills, MI, 2011, 503 pp.
2. Cyclic Response of Exterior Beam-Column Joints with Different Anchorage Methods
3. Shakya, K.; Matsumoto, K.; Watanabe, K.; and Niwa, J., “Cyclic Response of Beam-Column Joints of RC Bridges upon Partial Replacement of Steel Rebars with Steel Fibers,”Proceedings of the 9th CUEE and 4th ACEE Joint Conference, 2012, Tokyo, Japan, pp. 947-954.
4. Use of Headed Reinforcement in Beam-Column Joints Subjected to Earthquake Loads
5. Mechanical Anchorage in Exterior Beam-Column Joints Subjected to Cyclic Loading
6. Anchorage Strength and Behavior of Headed Bars in Exterior Beam-Column Joints
7. Seismic Design of Reinforced Concrete Beam-Column Joints with Headed Bars
8. Evaluation of Bond Strength of Bonded-In or Post-Installed Reinforcement
9. Tanaka, R., and Oba, K., “Experimental Study on Seismic Performance of Beam Members Connected with Post-Installed Anchors,”Proceedings of the Symposium on Connections between Steel and Concrete, Stuttgart, Germany, 2001, pp. 576-585.
10. Mahrenholtz, C.; Eligehausen, R.; Hofmann, J.; and Pampanin, S., “Bond Deterioration between Reinforcing Bars and Concrete Subject to Cyclic Loads and Cracks,”Proceedings of the Conference on Advances in Concrete through Science and Engineering (RILEM PRO 79), Hong Kong, 2011, pp. 560-567.
11. ASTM E488-96(2003), “Standard Test Methods for Strength of Anchors in Concrete and Masonry Elements,” ASTM International, West Conshohocken, PA, 2003, 8 pp.
12. Appl, J., “Tragverhalten von Verbunddübeln unter Zugbelastung (Load Bearing Behaviour of Bonded Anchors under Tension Loading),” PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2009, 276 pp. (in German)
13. Response of Reinforced Concrete Columns to Simulated Seismic Loading
14. Bond of Reinforcement under Controlled Confinement
15. Engström, B.; Magnusson, J.; and Huang, Z., “Pull-out Behavior of Ribbed Bars in Normal and High-strength Concrete with Various Confinements,”Proceedings of Bond and Development of Reinforcement: A Tribute to Dr. Peter Gergely, SP-180, R. Leon, ed., 1998, pp. 215-242.
16. Linear Elastic Fracture Mechanics Pullout Analyses of Headed Anchors in Stressed Concrete
17. Bruckner, M., “Anwendung von Ankerstäben in Rahmenecken, Rahmenendknoten und Stütze-Fundament-Verbindungen (Application of Headed Reinforcement in Frame Corners, Beam-Column Joints and Column-Foundation connections)”, PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2006, 200 pp. (in German)
18. ACI Committee 374, “Acceptance Criteria for Moment Frames Based on Structural Testing (ACI 3714.1-05) and Commentary,” American Concrete Institute, Farmington Hills, MI, 2005, 9 pp.
19. Zieliński, J., “Fracture of Concrete and Mortar under Uniaxial Impact Tensile Loading,” PhD dissertation, Delft University of Technology, Delft, the Netherlands, 1982, 162 pp.
20. An Attempt to Explain Strength Increase Due to High Loading Rates10.1016/0029-5493(89)90144-1 ↗
21. Compressive Behaviour of Concrete at High Strain Rates10.1007/BF02472016 ↗
22. Review of Strain Rate Effects for Concrete in Tension
23. Effect of Loading Rate on Load-Deflection Behavior and Failure Mode of Plain Concrete Slabs – 3D Finite Element Analysis Approach
24. Influence of Loading Rate on Bond Behaviour of Reinforcing Steel and Prestressing Strands10.1007/BF02473553 ↗
25. Eligehausen, R.; Popov, E.; and Bertero, V., “Local Bond Stress-Slip Relations of Deformed Bars under Generalized Excitations,”Report No. UCB/EERC 83-23, Earthquake Engineering Research Center, University of California, Berkeley, Berkeley, CA, Oct. 1983.
26. Weathersby, J., “Investigation of Bond Slip between Boncrete and Steel Reinforcement under Dynamic Loading Conditions,” PhD dissertation, Department of Civil and Environmental Engineering, Louisiana State University, Baton Rouge, LA, 2003, 280 pp.
27. Hoehler, M., “Behavior and Testing of Fastenings to Concrete for Use in Seismic Applications”, PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2006, 261 pp.
28. Evaluation of Ductility of Structures and Structural Assemblages from Laboratory Testing10.5459/bnzsee.22.3.155-166 ↗
29. Mahrenholtz, C., “Seismic Bond Model for Concrete Reinforcement and the Application to Column-to-Foundation Connections”, PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2012, 423 pp.
30. ATC-40, “Seismic Evaluation and Retrofit of Concrete Buildings,” Applied Technology Council, Redwood City, CA, 1996, 612 pp.
31. Towards a Consistent Design of Structural Concrete10.15554/pcij.05011987.74.150 ↗
32. Concrete Capacity Design (CCD) Approach for Fastening to Concrete
33. Behavior and Design of Single Adhesive Anchors under Tensile Load in Uncracked Concrete
34. Behavior and Design of Adhesive Bonded Anchors
35. ACI Committee 355, “Qualification of Post-Installed Adhesive Anchors in Concrete (ACI 355.4-11) and Commentary,” American Concrete Institute, Farmington Hills, MI, 2011, 55 pp.
36. Eligehausen, R.; Mallée, R.; and Silva, J.,Anchorage in Concrete Construction, Ernst & Sohn, Berlin, Germany, 2006, 391 pp.
37. Zhao, G.-C., “Tragverhalten von randfernen Kopfbolzenverankerungen bei Betonausbruch (Behavior of Headed Bolt Anchorages without Edge Influence),” PhD dissertation, University of Stuttgart, Stuttgart, Germany, 1993. (in German)
38. Varga, J., “Test Program for Fastenings with Headed Studs,”Test Report No. Te 696/1-95/4, Institute of Construction Materials, University of Stuttgart, Stuttgart, Germany, 1995, not published. (in German)
39. Varga, J., “Report on tests with headed anchors. Tensile and shear capacity of headed anchors with ribbed shafts,”Report No. 696/03-96/05, Institute of Construction Materials, University of Stuttgart, Stuttgart, Germany, 1996, not published. (in German)
40. Bruckner, M.; Eligehausen, R.; and Ožbolt, J., “Influence of Bending Compressive Stresses on the Concrete Cone Capacity,”Proceedings of the Symposium on Connections between Steel and Concrete, Stuttgart, Germany, 2001, pp. 647-657.
41. Fichtner, S., “Untersuchungen zum Tragverhalten von Gruppenbefestigungen unter Berücksichtigung der Ankerplattendicke und einer Mörtelschicht (Investigation on the Behaviour of Anchor Groups under Consideration of Anchor Plate Thickness and Mortar Layer),” PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2011. (in German)
42. Herzog, M., “Vereinheitlichung der Bemessung im Stahlbetonbau und der Befestigungstechnik (Unification of the Design Concept for Reinforced Concrete and Concrete Anchors),” PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2013. (in German)
43. Mahrenholtz, C.; Eligehausen, R.; and Hofmann, J., “Seismic Bond Model for Cast-in-Place and Post-Installed Reinforcing Bars,”Proceedings of the Conference on Bond in Concrete (BIC), Brescia, Italy, 2012, pp. 297-304.
44. Simulation of Monotonic and Cyclic Tests on Cast-in-Place and Post-Installed Column-to-Foundation Connections
45. Eligehausen, R.; Mahrenholtz, C.; Pampanin, S.; and Akguzel, U., “Bridging the Gap between Design Provisions for Connections using Anchorage or Strut- And Tie Models”,Symposium Honoring James O. Jirsa's Contributions in Structural Concrete: A Time to Reflect, SP-296, American Concrete Institute, Farmington Hills, MI, 2014, pp. 1-16.
46. Simons, I., “Verbundverhalten von eingemörtelten Bewehrungsstäben unter zyklischer Beanspruchung (Bond Behavior of Post-Installed Reinforcing Bars Subjected to Cyclic Loading),” PhD dissertation, University of Stuttgart, Stuttgart, Germany, 2007. (in German)
47. Cook, R.; Douglas, E.; Todd, D.; and Liu, C., “Long-Term Performance of Epoxy Adhesive Anchor Systems”,NCHRP Report 757, Transportation Research Board, Washington, DC, 2013, 279 pp.10.17226/22470 ↗