Influence of friction stir welding parameters on mechanical and electrochemical performance of EN AW-6082-T651 alloy butt joints
Source abstract
Abstract
Abstract This study investigates the influence of friction stir welding parameters, specifically tool rotational speed and linear speed, on the electrochemical and mechanical properties of EN AW-6082-T651 butt joints. The research encompassed microstructural analysis, surface roughness measurements, potentiodynamic corrosion tests, hardness profile measurement, and static tensile testing. Results revealed that decreasing the linear speed or increasing the rotational speed during welding intensified heat input, leading to grain growth in the weld nugget zone. The smallest grain size of 3.46 ± 1.11 µm was achieved at 1000 rpm and 250 mm/min. Surface roughness was minimized at 1250 rpm and 200 mm/min, as excessive tool feed caused irregularities. Corrosion resistance improved compared to the parent material, attributed to fine-grained structures promoting compact passive layer formation. Hardness profiling indicated the lowest values in the heat-affected zone, particularly for joints produced at 1250 rpm and 200 mm/min due to the highest heat input and precipitate dissolution. Tensile testing confirmed fracture locations in the heat-affected zone, with maximum tensile strength reaching 69% of the base material and elongation approximately 30%.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Ziółkowski W, Boroński D, Skibicki A, Stachowiak R, Kosturek R, Śnieżek L. Mechanical properties and microstructure of dissimilar S355/AA6061-T6 FSW butt joints. Materials (Basel). 2023. https://doi.org/10.3390/ma16175950.10.3390/ma16175950 ↗
2. Heidarzadeh A, Javidani M, Mofarrehi M, Farzaneh A, Chen XG. Submerged dissimilar friction stir welding of AA6061 and AA7075 aluminum alloys: microstructure characterization and mechanical property. Metals. 2021. https://doi.org/10.3390/met11101592.10.3390/met11101592 ↗
3. Nguyen TT, Nguyen CT, Van AL. Sustainability-based optimization of dissimilar friction stir welding parameters in terms of energy saving, product quality, and cost-effectiveness. Neural Comput Appl. 2023;35:5221–49. https://doi.org/10.1007/s00521-022-07898-8.10.1007/s00521-022-07898-8 ↗
4. Saad MH, Darras BM, Nazzal MA. Evaluation of welding processes based on multi-dimensional sustainability assessment model. International Journal of Precision Engineering and Manufacturing-Green Technology. 2021;8:57–75. https://doi.org/10.1007/s40684-019-00184-4.10.1007/s40684-019-00184-4 ↗
5. Laska A, Szkodo M, Pawłowski Ł, Gajowiec G. Corrosion properties of dissimilar AA6082/AA6060 friction stir welded butt joints in different NaCl concentrations. Int. J. Precis. Eng. Manuf. - Green Technol. 2022, https://doi.org/10.1007/s40684-022-00441-z.10.1007/s40684-022-00441-z ↗
6. Ancona A, Daurelio G, De Filippis L.A.C., Ludovico AD, Spera AM. CO2 Laser Welding of Aluminium Shipbuilding Industry Alloys: AA 5083, AA 5383, AA 5059, and AA 6082. In Proceedings of the XIV International Symposium on Gas Flow, Chemical Lasers, and High-Power Lasers; 2002;577–587.10.1117/12.515825 ↗
7. Dursun T, Soutis C. Recent developments in advanced aircraft aluminium alloys. Mater Des. 2014;56:862–71. https://doi.org/10.1016/j.matdes.2013.12.002.10.1016/j.matdes.2013.12.002 ↗
8. Qin H, Zhang H, Sun D, Zhuang Q. Corrosion behavior of the friction-stir-welded joints of 2A14-T6 aluminum alloy. Int. J. Miner. Metall. Mater. 2015;22:627–638, https://doi.org/10.1007/s12613-015-1116-9.10.1007/s12613-015-1116-9 ↗
9. Gharavi F, Matori KA, Yunus R, Othman NK, Fadaeifard F. Corrosion evaluation of friction stir welded lap joints of AA6061-T6 aluminum alloy. Trans Nonferrous Met Soc China. 2016;26:684–96. https://doi.org/10.1016/S1003-6326(16)64159-6.10.1016/S1003-6326(16)64159-6 ↗
10. Ales SK, Wang L. Effects of Friction Stir Welding on Corrosion Behaviors of AA2024-T4 Aluminum Alloy. MATEC Web Conf. 2017;109:02003, https://doi.org/10.1051/matecconf/201710902003.10.1051/matecconf/201710902003 ↗
11. Sajjad U, Abbas A, Sadeghianjahromi A, Abbas N, Liaw JS, Wang CC. Enhancing corrosion resistance of Al 5050 alloy based on surface roughness and its fabrication methods; an experimental investigation. J Mater Res Technol. 2021;11:1859–67. https://doi.org/10.1016/j.jmrt.2021.01.096.10.1016/j.jmrt.2021.01.096 ↗
12. Dawood HI, Mohammed KS, Rahmat A, Uday MB. The influence of the surface roughness on the microstructures and mechanical properties of 6061 aluminium alloy using friction stir welding. Surf Coatings Technol. 2015;270:272–83. https://doi.org/10.1016/j.surfcoat.2015.02.045.10.1016/j.surfcoat.2015.02.045 ↗
13. Laska A, Szkodo M. Manufacturing Parameters, Materials, and Welds Properties of Butt Friction Stir Welded Joints-Overview. Materials (Basel). 2020;13:1–46. https://doi.org/10.3390/ma13214940.10.3390/ma13214940 ↗
14. Jamshidi Aval H. Microstructure and residual stress distributions in friction stir welding of dissimilar aluminium alloys. Mater Des. 2015;87:405–13. https://doi.org/10.1016/j.matdes.2015.08.050.10.1016/j.matdes.2015.08.050 ↗
15. Kumar Maurya S, Chechi P, Prasad R, Kant Susheel C, Manna A. Effect of surface finish on corrosion behavior of polished Al6061 alloy in simulated acid rain environment. Mater Today Proc. 2022;64:755–9. https://doi.org/10.1016/j.matpr.2022.05.208.10.1016/j.matpr.2022.05.208 ↗
16. Bhushan RK, Sharma D. Investigation of mechanical properties and surface roughness of friction stir welded AA6061-T651. Int J Mech Mater Eng. 2020. https://doi.org/10.1186/s40712-020-00119-x.10.1186/s40712-020-00119-x ↗
17. Wen Q, Li WY, Wang WB, Wang FF, Gao YJ, Patel V. Experimental and numerical investigations of bonding interface behavior in stationary shoulder friction stir lap welding. J Mater Sci Technol. 2019;35:192–200. https://doi.org/10.1016/j.jmst.2018.09.028.10.1016/j.jmst.2018.09.028 ↗
18. Almansour A, Azizi M, Jesri A.M, Entakly S. Effect of deformation Processes on Corrosion Behavior of AA6061 in Salt Solution ( 3 . 5 % NaCl ). IJASR Int. J. Acad. Sci. Res. 2014;2:71–77.
19. Ralston KD, Fabijanic D, Birbilis N. Effect of grain size on corrosion of high purity aluminium. Electrochim Acta. 2011;56:1729–36. https://doi.org/10.1016/j.electacta.2010.09.023.10.1016/j.electacta.2010.09.023 ↗
20. Xue L, Ding Y, Pradeep KG, Case R, Castaneda H, Paredes M. The grain size effect on corrosion property of Al2Cr5Cu5Fe53Ni35 high-entropy alloy in marine environment. Corros Sci. 2022. https://doi.org/10.1016/j.corsci.2022.110625.10.1016/j.corsci.2022.110625 ↗
21. Song D, Ma A, Jiang J, Lin P, Yang D. Corrosion behavior of ultra-fine grained industrial pure Al fabricated by ECAP. Trans Nonferrous Met Soc China. 2009;19:1065–70. https://doi.org/10.1016/S1003-6326(08)60407-0.10.1016/S1003-6326(08)60407-0 ↗
22. Laska A, Sadeghi B, Sadeghian B, Taherizadeh A, Szkodo M, Cavaliere P. Temperature evolution, material flow, and resulting mechanical properties as a function of tool geometry during friction stir welding of AA6082. J Mater Eng Perform. 2023;32:10655–68. https://doi.org/10.1007/s11665-023-08671-1.10.1007/s11665-023-08671-1 ↗
23. Laska A, Szkodo M, Koszelow D, Cavaliere P. Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082. Metals (Basel). 2022;12:1–16. https://doi.org/10.3390/met12020192.10.3390/met12020192 ↗
24. Laska A, Szkodo M, Cavaliere P, Moszczynska D, Mizera J. Analysis of residual stresses and dislocation density of AA6082 butt welds produced by friction sir welding. Metall Mater Trans A. 2022. https://doi.org/10.1007/s11661-022-06862-4.10.1007/s11661-022-06862-4 ↗
25. Pabandi HK, Jashnani HR, Paidar M. Effect of precipitation hardening heat treatment on mechanical and microstructure features of dissimilar friction stir welded AA2024-T6 and AA6061-T6 alloys. J Manuf Process. 2018;31:214–20. https://doi.org/10.1016/j.jmapro.2017.11.019.10.1016/j.jmapro.2017.11.019 ↗
26. Fathi J, Ebrahimzadeh P, Farasati R, Teimouri R. Friction stir welding of aluminum 6061–T6 in presence of watercooling: analyzing mechanical properties and residual stress distribution. Int J Lightweight Mater Manuf. 2019;2:107–15. https://doi.org/10.1016/j.ijlmm.2019.04.007.10.1016/j.ijlmm.2019.04.007 ↗
27. Liu HJ, Zhang HJ, Huang YX, Yu L. Mechanical properties of underwater friction stir welded 2219 aluminum alloy. Trans Nonferrous Met Soc China. 2010;20:1387–91. https://doi.org/10.1016/S1003-6326(09)60309-5.10.1016/S1003-6326(09)60309-5 ↗
28. Patel V, De Backer J, Hindsefelt H, Igestrand M, Azimi S, Andersson J, et al. High speed friction stir welding of AA6063-T6 alloy in lightweight battery trays for EV industry: influence of tool rotation speeds. Mater Lett. 2022. https://doi.org/10.1016/j.matlet.2022.132135.10.1016/j.matlet.2022.132135 ↗
29. Rajendran C, Parthiban G, Pranav K, Nithi Balaji SP. Influence of solution treatment and artificial aging on fracture load of friction stir welded lap joints of AA2014-T6. IOP Conf Ser Mater Sci Eng. 2021. https://doi.org/10.1088/1757-899X/1059/1/012037.10.1088/1757-899X/1059/1/012037 ↗