Technological Shells in Rolling Processes of Thin Sheets from Hard-to-Deform Materials
Source abstract
Abstract
Innovations in many strategically important sectors, such as the aerospace, automotive, energy and other industries, depend on making products from hard-to-deform materials. The most promising technology for their forming is rolling in a ductile shell. Even though the use of such technological shells allows one to effectively reduce rolling forces and soften the stress state, they have not found wide application in manufacturing practice due to the accompanying disadvantages: dog boning effect, high thickness variation, shell delamination during rolling and the lack of comprehensive studies on the influence of shell material on the process parameters. This study used finite element (FE) simulation to analyze the impact of shell material on the process parameters of rolling with the use of shells. On the basis of FE simulation, a new shell design was proposed. The key difference between the new shell design and the well-known one lies in the two-layer construction of the proposed shells. The FE model of the rolling process with the use of the modified technological shells and testing on the example of high-carbon tool steel under laboratory conditions have shown an improvement in the process parameters and high potential for use in real manufacturing processes.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Metal Alloys Wear and Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. M.Ya. Dzugutov, Plastic Deformation of High-Alloyed Steels and Alloys, (Moscow) Metallurgija (1977) (in Russian)
2. J. Samei, Y. Salib, M. Amirmaleki, and D.S. Wilkinson, The Role of Microstructure on Edge Cracks in Dual Phase and Quench and Partitioning Steels Subject to Severe Cold Rolling, Scr. Mater., 2019, 173, p 86–90.10.1016/j.scriptamat.2019.08.012 ↗
3. R.G. Davies, Edge Cracking in High Strength Steels, J. Appl. Metalwork., 1983, 4(2), p 293–299.10.1007/BF02833914 ↗
4. M. Terčelj, R. Turk, G. Kugler, and I. Peruš, Neural Network Analysis of the Influence of Chemical Composition on Surface Cracking During Hot Rolling of AISI D2 Tool Steel, Comput. Mater. Sci., 2008, 42(4), p 625–637.10.1016/j.commatsci.2007.09.009 ↗
5. C.C. Szilvassy and W.C.K. Wong, Statistical Classification of Chemical Composition and Microstructure as a Function of Tool-Steel Deformability, J. Mater. Process Technol., 1992, 29, p 191–202.10.1016/0924-0136(92)90434-T ↗
6. M. Rosso, D. Ugues, and M. Actis Grande, The Challenge of PM Tool Steels for the Innovation, J. Achiev. Mater. Manuf. Eng., 2006, 18(1–2), p 175–178.
7. M. Pekguleryuza, M. Celikina, M. Hoseinia, A. Becerrab, and L. Mackenzie, Study on Edge Cracking and Texture Evolution During 150 °C Rolling of Magnesium Alloys: The Effects of Axial Ratio and Grain Size, J. Alloys Compd., 2012, 510, p 15–25.10.1016/j.jallcom.2011.08.093 ↗
8. T. Mineta, K. Hasegawa, and H. Sato, High Strength and Plastic Deformability of Mg–Li–Al Alloy with Dual BCC Phase Produced by a Combination of Heat Treatment and Multi-directional Forging in Channel Die, Mater. Sci. Eng. A, 2020, 773, p 1–8.10.1016/j.msea.2019.138867 ↗
9. W. Jia, L. Maa, and M. Jiao, Fracture Criterion for Predicting Edge-Cracking in Hot Rolling of Twin-Roll Casted AZ31 Mg Alloy, J. Mater. Res. Technol., 2020, 9(3), p 4773–4787.10.1016/j.jmrt.2020.02.103 ↗
10. M. Scapin, L. Peroni, and F. Carra, Investigation and Mechanical Modelling of Pure Molybdenum at High Strain-Rate and Temperature, J. Dyn. Behav. Mater., 2016, 2, p 460–475.10.1007/s40870-016-0081-3 ↗
11. A. Soulami, D.E. Burkes, V.V. Joshi, C.A. Lavender, and D. Paxton, Finite-Element Model to Predict Roll-Separation Force and Defects During Rolling of U-10Mo Alloys, J. Nucl. Mater., 2017, 494, p 182–191.10.1016/j.jnucmat.2017.07.006 ↗
12. T.A. Pedrosa, J.G.M. Brina, J.Bd. Paula et al., Preliminary results for the co-rolling process fabrication of plate-type nuclear fuel based in U-10Mo monolithic meat and zircaloy-4 cladding, in International Nuclear Atlantic Conference - INAC 2013 (2013), p 1–12
13. J. Zhang, W. Yu, E. Dong et al., Study on Grinding and Deformation Fracture Control of Cold Rolled Titanium Strip, Metals, 2020, 10(323), p 1–11.
14. D.C.J. Farrugia, Prediction and Avoidance of High Temperature Damage in Long Product Hot Rolling, J. Mater. Process. Technol., 2006, 177, p 486–492.10.1016/j.jmatprotec.2006.03.236 ↗
15. B. Zhu, X. Liu, Ch. Xie et al., Unveiling the Underlying Mechanism of Forming Edge Cracks Upon High Strain-Rate Rolling of Magnesium Alloy, J. Mater. Sci. Technol., 2020, 50, p 59–65.10.1016/j.jmst.2020.03.006 ↗
16. H. Riedel, F. Andrieux, T. Walde, and K.-F. Karhausen, The Formation of Edge Cracks During Rolling of Metal Sheet, Steel Res. Int., 2007, 78(10–11), p 818–824.10.1002/srin.200706291 ↗
17. C. Hubert, L. Dubar, M. Dubar, and A. Dubois, Finite Element Simulation of the Edge-Trimming/Cold Rolling Sequence: Analysis of Edge Cracking, J. Mater. Process Technol., 2012, 212, p 1049–1060.10.1016/j.jmatprotec.2011.12.011 ↗
18. B. Dodd and P. Boddington, The Causes of Edge Cracking in Cold Rolling, J. Mech. Work. Technol., 1980, 3, p 239–252.10.1016/0378-3804(80)90045-5 ↗
19. R.R. Arnold and P.W. Whitton, Stress and Deformation Studies for Sandwich Rolling Hard Metals, Proc. Inst. Mech. Eng., 1959, 8(173), p 241–256.10.1243/PIME_PROC_1959_173_030_02 ↗
20. A.A. Afonja and D.H. Sansome, A Theoretical Analysis of the Sandwich Rolling Process, Int. J. Mech. Sci., 1973, 15, p 1–14.10.1016/0020-7403(73)90042-8 ↗
21. M.N. Huang, G.Y. Tzou, and S.W. Syu, Investigation on Comparisons Between Two Analytical Models of Sandwich Sheet Rolling Bonded Before Rolling, J. Mater. Process Technol., 2003, 140, p 598–603.10.1016/S0924-0136(03)00799-4 ↗
22. A.G. Atkins and A.S. Weinstein, The Deformation of Sandwich Materials, Int. J. Mech. Sci., 1970, 12, p 641–657.10.1016/0020-7403(70)90094-9 ↗
23. S. Li, C. Luo, and Z. Lio, Interface Characteristics and Mechanical Behavior of Cu/Al Clad Plate Produced by the Corrugated Rolling Technique, J. Manuf. Process, 2020, 60, p 75–85.10.1016/j.jmapro.2020.10.015 ↗
24. H. Utsunomiya, S. Maeda, T. Imai, and R. Matsumoto, Necking Condition of Layers in Clad Sheets During Rolling, CIRP Ann. Manuf. Technol., 2018, 67, p 317–320.10.1016/j.cirp.2018.04.056 ↗
25. T. Imai, H. Utsunomiya, and R. Matsumoto, Finite Element Analysis of Plastic Instability Phenomenon in Cold Rolling of Clad Sheets, Procedia Eng., 2017, 184, p 306–312.10.1016/j.proeng.2017.04.099 ↗
26. F. Nowicke Jr., A. Zavaliangos, and H.C. Rogers, The Effect of Roll and Clad Sheet Geometry on the Necking Instability During Rolling of Clad Sheet Metals, Int. J. Mech. Sci., 2006, 48, p 868–877.10.1016/j.ijmecsci.2006.01.021 ↗
27. P. Clerico, X. Mininger, L. Prevond et al., Compromise Between Magnetic Shielding and Mechanical Strength of Thin Al/Steel/Al Sandwiches Produced by Cold Roll Bonding: Experimental and Numerical Approaches, J. Alloys Compd., 2019, 798, p 67–81.10.1016/j.jallcom.2019.05.243 ↗
28. H. Yu, A.K. Tieu, and C. Lu, A Deformation Mechanism of Hard Metal Surrounded by Soft Metal During Roll Forming, Sci. Rep., 2014. https://doi.org/10.1038/srep0501710.1038/srep05017 ↗
29. S.L. Semiatin and H.R. Piehler, Formability of Sandwich Sheet Materials in Plane Strain Compression and Rolling, Metall. Mater. Trans. A, 1979, 1(10A), p 97–107.10.1007/BF02686412 ↗
30. Y.-M. Hwang, H.-H. Hsu, and H.-J. Lee, Analysis of Plastic Instability during Sandwich Sheet Rolling, Int. J. Math. Tools Manufact., 1996, 1(36), p 47–62.10.1016/0890-6955(95)92628-C ↗
31. D. Salikhyanov, Contact Mechanism Between Dissimilar Materials Under Plastic Deformation, C. R. Mec., 2019, 8(347), p 588–600.10.1016/j.crme.2019.07.002 ↗
32. H. Haghighat and P. Saadati, An Upper Bound Analysis of Rolling Process of Non-bonded Sandwich Sheets, Trans. Nonferrous Met. Soc. China, 2015, 25, p 1605–1613.10.1016/S1003-6326(15)63764-5 ↗
33. H. Danesh Manesh and A. Karimi Taheri, Theoretical and Experimental Investigation of Cold Rolling of Tri-layer Strip, J. Mater. Process Technol., 2005, 166, p 163–172.10.1016/j.jmatprotec.2004.08.010 ↗
34. M. Caruso and B. Pohu, Process parameters for the production of steel roll-bonded multilayer plates and strips, in European Steel Technology and Application Days 2017 – ESTAD 2017 (2017), p 1–10
35. H.Y. Wang, X. Li, and J. Sun, Analysis of Sandwich Rolling with Two Different Thicknesses Outer Layers Based on Slab Method, Int. J. Mech. Sci., 2016, 106, p 194–208.10.1016/j.ijmecsci.2015.12.021 ↗
36. A. Soulami, C.A. Lavender, D.M. Paxton, and D. Burkes, Rolling Process Modeling, Report: Finite-Element Prediction of Roll Separating Force and Rolling Defects, PNNL-23313 (Pacific Northwest National Laboratory, Richland, 2014)10.2172/1177322 ↗
37. D.I. Vichuzhanin, V.A. Khotinov, and S.V. Smirnov, The Effect of the Stress State on the Ultimate Plasticity of Steel X80, Diagn. Resour. Mech. Mater. Struct., 2015, 1, p 73–89.
38. P.I. Polukhin, G.Ya. Gun, and A.M. Galkin, Resistance to plastic deformation of metals and alloys, (Moscow) Metallurgija (1983) (in Russian)
39. A. Mozaffari, H. Danesh Manesh, and K. Janghorban, Evaluation of Mechanical Properties and Structure of Multilayered Al/Ni Composites Produced by Accumulative Roll Bonding (ARB) Process, J. Alloys Compd., 2010, 489, p 103–109.10.1016/j.jallcom.2009.09.022 ↗