Evaluation of Microstructure, Mechanical Properties and Corrosion Resistance of Friction Stir-Welded Aluminum and Magnesium Dissimilar Alloys
Source abstract
Abstract
Microstructure, mechanical properties and corrosion resistance of dissimilar friction stir-welded aluminum and magnesium alloys were investigated by applying three different rotational speeds at two different travel speeds. Sound joints were obtained in all the conditions. The microstructure was examined by an optical and scanning electron microscope, whereas localized chemical information was studied by energy-dispersive spectroscopy. Stir zone microstructure showed mixed bands of Al and Mg with coarse and fine equiaxed grains. Grain size of stir zone reduced compared to base metals, indicated by dynamic recrystallization. More Al patches were observed in the stir zone as rotational speed increased. X-ray diffraction showed the presence of intermetallics in the stir zone. Higher tensile strength and hardness were obtained at a high rotational speed corresponding to low travel speed. Tensile fractured surface indicated brittle nature of joints. Dissimilar friction stir weld joints showed different behaviors in different corrosive environments, and better corrosion resistance was observed at a high rotational speed corresponding to low travel speed (FW3) in a sulfuric and chloride environments. Increasing travel speed did not significantly affect on microstructure, mechanical properties and corrosion resistance as much as the rotational speed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. A. Pardo, M.C. Merino, A.E. Coy, R. Arrabal, F. Viejo, and E. Matykina, Corrosion Behavior of Magnesium/Aluminum Alloys in 3.5 wt% NaCl, Corros. Sci., 2008, 50, p 823–83410.1016/j.corsci.2007.11.005 ↗
2. J.E. Gray and B. Luan, Protective Coatings on Magnesium and its Alloys—A Critical Review, J. Alloys. Compd., 2002, 336, p 88–11310.1016/S0925-8388(01)01899-0 ↗
3. M. Yamamoto, A. Gerlich, T.H. North, and K. Shinozaki, Cracking and Local Melting in Mg-Alloy and Al-Alloy During Friction Stir Spot Welding, Weld. World, 2013, 52, p 38–4610.1007/BF03266667 ↗
4. M.A. Mofid and F.M. Ghaini, The Effect of Water Cooling During Dissimilar Friction Stir Welding of Al Alloy to Mg Alloy, Mater. Des., 2012, 36, p 161–16710.1016/j.matdes.2011.11.004 ↗
5. Y.J. Kwon, I. Shigematsu, and N. Saito, Dissimilar Friction Stir Welding between Magnesium and Aluminum Alloys, Mater. Lett., 2008, 62, p 3827–382910.1016/j.matlet.2008.04.080 ↗
6. V. Firouzdor and S. Kou, Al-to-Mg Friction Stir Welding: Effect of Material Position, Travel Speed and Rotation Speed, Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2010, 41, p 2914–293510.1007/s11661-010-0340-1 ↗
7. D. Liu, H. Nishio, and K. Nakata, Anisotropic Property of Material Arrangement in Friction Stir Welding of Dissimilar Mg Alloys, Mater. Des., 2011, 32, p 4818–482410.1016/j.matdes.2011.06.020 ↗
8. M. Pourali, A. Abdollah-zadeh, T. Saeid, and F. Kargar, Influence of Welding Parameters on Intermetallic Compounds Formation in Dissimilar Steel/Aluminum Friction Stir Welds, J. Alloy. Compd., 2017, doi: 10.1016/j.jallcom.2017.04.27210.1016/j.jallcom.2017.04.272 ↗
9. X. Liu, S. Lan, and J. Ni, Analysis of Process Parameters Effects on Friction Stir Welding of Dissimilar Aluminum Alloy to Advanced High Strength Steel, Mater. Des., 2014, 59, p 50–6210.1016/j.matdes.2014.02.003 ↗
10. M.A. Mofid, A. Abdollah-zadeh, and F. Malek Ghaini, The Effect of Water Cooling During Dissimilar Friction Stir Welding of Al Alloy to Mg Alloy, Mater. Des., 2012, 36, p 161–16710.1016/j.matdes.2011.11.004 ↗
11. J. Mohammadi, Y. Behnamian, A. Mostafaei, H. Izadi, T. Saeid, A.H. Kokabi, and A.P. Gerlich, Friction Stir Welding Joint of Dissimilar Materials Between AZ31B Magnesium and 6061 Aluminum Alloys: Microstructure Studies and Mechanical Characterizations, Mater. Charact., 2015, 101, p 189–20710.1016/j.matchar.2015.01.008 ↗
12. K. Lee and E. Kwon, Microstructure of Stir Zone in Dissimilar Friction Stir Welds of AA6061-T6 And AZ31 Alloy Sheets, Trans. Nonferrous Met. Soc. China, 2014, 24, p 2374–237910.1016/S1003-6326(14)63359-8 ↗
13. G. Padmanaban and V. Balasubramanian, An Experimental Investigation on Friction Stir Welding of AZ31B Magnesium Alloy, Int. J. Adv. Manuf. Technol., 2010, 49, p 111–12110.1007/s00170-009-2368-1 ↗
14. A.C. Somasekharan and L.E. Murr, Microstructures in Friction-Stir Welded Dissimilar Magnesium Alloys and Magnesium Alloys to 6061-T6 Aluminum Alloy, Mater. Charact., 2004, 52, p 49–6410.1016/j.matchar.2004.03.005 ↗
15. W.S. Chang, S.R. Rajesh, C.K. Chun, and H.J. Kim, Microstructure and Mechanical Properties of Hybrid Laser-Friction Stir Welding between AA6061-T6 Al Alloy and AZ31 Mg Alloy, J. Mater. Sci. Technol., 2011, 27, p 199–20410.1016/S1005-0302(11)60049-2 ↗
16. C.B. Jagadeesha, Dissimilar Friction Stir Welding between Aluminum Alloy and Magnesium Alloy at a Low Rotational Speed, Mater. Sci. Eng., A, 2014, 616, p 55–6210.1016/j.msea.2014.07.090 ↗
17. ASTM E 8-04, Standard Practice for Preparation Tension Testing of Metallic Materials, Philadelphia, PA, USA, 2004
18. Y.H. Yin, N. Sun, T.H. North, and S.S. Hu, Hook Formation and Mechanical Properties in AZ31 Friction Stir Spot Welds, J. Mater. Process. Technol., 2010, 210, p 2062–207010.1016/j.jmatprotec.2010.07.029 ↗
19. A. Kostka, R.S. Coelho, J.D. Santos, and A.R. Pyzalla, Microstructure of Friction Stir Welding of Aluminium Alloy to Magnesium Alloy, Scripta Mater., 2009, 60, p 953–95610.1016/j.scriptamat.2009.02.020 ↗
20. M. Azizieh, A. Sadeghi Alavijeh, M. Abbasi, Z. Balak, and H.S. Kim, Mechanical Properties and Microstructural Evaluation of AA1100 to AZ31 Dissimilar Friction Stir Welds, Mater. Chem. Phys., 2016, 170, p 251–26010.1016/j.matchemphys.2015.12.046 ↗
21. M. Jabbari and C.C. Tutum, Optimum rotation Speed for the Friction Stir Welding of Pure Copper, ISRN Mater. Sci., 2013, doi: 10.1155/2013/97803110.1155/2013/978031 ↗
22. K. Surekha, B.S. Murty, and K. Prasad Rao, Effect of Processing Parameters on the Corrosion Behaviour of Friction Stir Processed AA 2219 Aluminum Alloy, Solid State Sci., 2009, 11, p 907–91710.1016/j.solidstatesciences.2008.11.007 ↗
23. P. Pourahmad and M. Abbasi, Materials Flow and Phase Transformation in Friction Stir Welding of Al 6013/Mg, Trans. Nonferrous Met. Soc. China, 2013, 23, p 1253–126110.1016/S1003-6326(13)62590-X ↗
24. J. Yan, Z. Xu, Z. Li, L. Li, and S. Yang, Microstructure Characteristics and Performance of Dissimilar Welds between Magnesium Alloy and Aluminium, Scripta Mater., 2005, 53, p 585–58910.1016/j.scriptamat.2005.04.022 ↗
25. A. Gerlich, P. Su, M. Yamamoto, and T.H. North, Material Flow and Intermixing During Dissimilar Friction Stir Welding, Sci. Technol. Weld. Join., 2008, 13, p 254–26410.1179/174329308X283910 ↗
26. H.M. Rao, W. Yuan, and H. Badarinarayan, Effect of Process Parameters on Mechanical Properties of Friction Stir Spot Welded Magnesium to Aluminum Alloys, Mater. Des., 2015, 66, p 235–24510.1016/j.matdes.2014.10.065 ↗
27. S.H.C. Park, Y.S. Sato, and H. Kokawa, Microstructural Evolution and its Effect on Hall-Petch Relationship in Friction Stir Welding of Thixomolded Mg Alloy AZ91D, J. Mater. Sci., 2003, 38, p 4379–438310.1023/A:1026351619636 ↗
28. C. Liu, D.L. Chen, S. Bhole, X. Cao, and M. Jahazi, Polishing-Assisted Galvanic Corrosion in the Dissimilar Friction Stir Welded Joint of AZ31 Magnesium Alloy to 2024 Aluminum Alloy, Mater. Charact., 2009, 60, p 370–37610.1016/j.matchar.2008.10.009 ↗
29. R.S. Mishra and Z.Y. Ma, Friction Stir Welding and Processing, Mater. Sci. Eng., R, 2005, 60, p 1–7810.1016/j.mser.2005.07.001 ↗
30. G. Song, A. Atrens, X. Wu, and B. Zhang, Corrosion Behaviour of AZ10 AZ490 and AZ80 in Sodium Chloride, Corros. Sci., 1998, 40, p 1769–179110.1016/S0010-938X(98)00078-X ↗
31. K. Amini and F. Gharavi, Influence of Welding Speed on Corrosion Behaviour of Friction Stir Welded AA5086 Aluminium Alloy, J. Cent. South Univ., 2016, doi: 10.1007/s11771-016-3180-310.1007/s11771-016-3180-3 ↗
32. K. Jafarzadeh, T. Shahrabiand, and M.G. Hosseini, EIS Study on Pitting Corrosion of AA5083-H321 Aluminum-Magnesium Alloy in Stagnant 3.5% NaCl Solution, J. Mater. Sci. Technol., 2008, 24, p 215–219
33. D. Mercier, M. Herinx, and M.G. Barthés-Labrousse, Influence of 1,2-Diaminoethane on the Mechanism of Aluminium Corrosion in Sulphuric Acid Solutions, Corros. Sci., 2010, 52, p 3405–341210.1016/j.corsci.2010.06.022 ↗