An Investigation into the Mechanisms of B2-NiAl in the Thermal Conductivity and Mechanical Properties of Light Duplex Steel
Source abstract
Abstract
In this work, the microstructure, mechanical properties and thermal conductivity of the xNiAl/Fe−20Cr-15Ni-6Al-2Mo (x = 0, 10, 20, 30 wt.%) prepared by mechanical alloying and vacuum hot-pressing sintering were investigated. The experimental results revealed that the primary phases of the material after NiAl addition were the austenite phase, ferrite phase and B2-NiAl phase. The addition of B2-NiAl significantly improved the thermal conductivity of the materials, especially when the NiAl content was 30 wt.%, and the thermal conductivity at room temperature was 16.91 W/(m·k), which was 67.59% higher than that of the matrix material. As the NiAl content increased, the tensile strength and elongation after fracture of the materials first increased and then decreased. The 20 wt.% NiAl material had excellent values of 1215.41 MPa and 6.09%, which were 106.76% and 53.40% greater than that of the matrix alloy.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Wen Zhang and Xu. Jun, Advanced Lightweight Materials for Automobiles: A Review, Mater. Design, 2022, 221, p 11094.
2. Yu. Jingyi, Mu. Rende, Qu. Shiyu, Y. Cai, and Z. Shen, The Effect of Heat Treatment at 1200 °C on Microstructure and Mechanical Properties Evolution of AlCoCrFeNiSiYHf High Entropy Alloys, Vacuum, 2022, 200, 111039.10.1016/j.vacuum.2022.111039 ↗
3. D. Wang, S. Li, and C. Xie, Crashworthiness Optimisation and Lightweight for Front-End Safety Parts of Automobile Body Using a Hybrid Optimisation Method, Int. J. Crashworthiness, 2022, 27(4), p 1193–1204.10.1080/13588265.2021.1926809 ↗
4. Su. Ting, T. He, R. Yang, and M. Li, Topology Optimization and Lightweight Design of Stamping Dies for Forming Automobile Panels, Int. J. Adv. Manuf. Technol., 2022, 121(7–8), p 4691–4702.
5. F.E.K. Sato and T. Nakata, Analysis of the Impact of Vehicle Lightweighting on Recycling Benefits Considering Life Cycle Energy Reductions, Resour. Conserv. Recycl., 2021, 164(1), 105118.10.1016/j.resconrec.2020.105118 ↗
6. N. Zhao, M. Ding, Li. Lin, Y. He, J. Wang, Yu. Ruikun Zhang, R.L. Zhang, L. Wang, and L. Li, Insights into the Relationship Between γ/α Transformation and Strength-Ductility of Auto-Steel with 980 MPa Grade Based on Experiments and Theoretical Calculations, Vacuum, 2023, 215, 112252.10.1016/j.vacuum.2023.112252 ↗
7. D. Wang and S. Li, Collaborative Optimization Design of Lightweight and Crashworthiness of the Front-End Structures of Automobile Body Using HW-GRA for Pareto Mining, Proc. Inst. Mech. Eng. C J. Mech. Eng. Sci., 2021, 235(21), p 5201–5215.10.1177/0954406221992802 ↗
8. Y. Zhang, Y. Shan, X. Liu, and T. He, An Integrated Multi-Objective Topology Optimization Method for Automobile Wheels Made of Lightweight Materials, Struct. Multidisciplin. Optimiz., 2021, 64, p 1585–1605.10.1007/s00158-021-02913-3 ↗
9. X. Pan, Y. Xiong, C. Wang, J. Qin, S. Zhang, and W. Bao, Performance Analysis of Precooled Turbojet Engine with a Low-Temperature Endothermic Fuel, Energy, 2022, 248, 123582.10.1016/j.energy.2022.123582 ↗
10. T.M. Yunus Khan, A Review of Performance-Enhancing Innovative Modifications in Biodiesel Engines, Energies, 2020, 13(17), p 4395.10.3390/en13174395 ↗
11. Q.D. Tran, T.T. Tran, and V.N. Duy, An Experimental Investigation on Performance of Converted CNG Engine by Varying Piston Bowl Geometry: A Case Study, J. Air & Waste Manag. Assoc., 2022, 72, p 361–369.10.1080/10962247.2022.2028689 ↗
12. Y.Z. GangLiu, K. Huang, and W. Zhuge, Cyclic Coupling Mechanisms in a Novel Turbo-Piston Combined Cycle Engine Concept for Heavy Vehicle Applications, Appl. Thermal Eng., 2022, 209, p 118284.10.1016/j.applthermaleng.2022.118284 ↗
13. Y. Li, W. Han, L. Yanli Liu, Y.Q. Zhang, W. Liu, J. Liu, H. Bai, C. Hao, and Y. Li, Study on Engine Performance and Combustion System Optimization of a Poppet-Valve Two-Stroke Diesel Engine, Energies, 2022, 15, p 3685.10.3390/en15103685 ↗
14. H. Mu, Y. Wang, C. Yang, H. Teng, X. Zhao, H. Lu, D. Wang, Shiyang Hao, Xiaolong Zhang, Yan Jin. Technical research on improving engine thermal efficiency. Adv. Mech. Eng. 2022, 14(9).10.1177/16878132221125032 ↗
15. F. Meng, Z. Zhang, Wu. Bin, Hu. Wei, X. Ai, X. Meng, Ze. Ding, and L. Zhang, Turning Processes and Mechanism of Compacted graphite iron used for high performance Engine, J. Manuf. Process., 2021, 68(3), p 951–960.10.1016/j.jmapro.2021.06.014 ↗
16. B. Pavani Srikavya, P. Srinivasa Rao, Syed Kamaluddin. Lightweight Materials for Engine Cylinder Blocks/Liners—A Critical Review [J]. Advanced Manufacturing Systems and Innovative Product Design, 2021, 103-116.10.1007/978-981-15-9853-1_10 ↗
17. L. Qiao, Yu. Jingchuan Zhu, A.B. Teng, Z. Lai, and Y. Wang, Dynamic Solidification Model of Low-Density FeCrNiAl Multi-Component Alloy, Vacuum, 2021, 184, 109873.10.1016/j.vacuum.2020.109873 ↗
18. C. Kim, H. Kim, W. Heo, C. Jang, S.Y. Lee, S. Lee, and J.-S. Lee, High-Temperature Steam Oxidation Behavior of Alumina-Forming Duplex FeNiCrAl and ferritic FeCrAl alloys at 800 °C to 1050 °C, Corrosion Sci., 2021, 190, 109658.10.1016/j.corsci.2021.109658 ↗
19. L. Qiao, A. Bao, Y. Wang, Y. Liu, Z. Lai, and J. Zhu, Thermophysical Properties and High Temperature Oxidation Behavior of FeCrNiAl 0.5 Multi-Component Alloys, Intermetallic, 2020, 126, 106899.10.1016/j.intermet.2020.106899 ↗
20. J. Wang, Wu. Qingfeng, Y. Li, Z. Wang, J. Li, and J. Wang, Phase Selection of BCC/B2 Phases for the Improvement of Tensile Behaviors in FeNiCrAl Medium Entropy Alloy, J. Alloy. Compd., 2022, 916, 165382.10.1016/j.jallcom.2022.165382 ↗
21. P. Andrew and B. Ian, Analysis of the Elevated Temperature Deformation Mechanisms and Grain Boundary Strengthening of the Alumina-Forming Austenitic Stainless-Steel Fe–20Cr–30Ni–2Nb–5Al, Mater. Sci. Eng., A, 2021, 814, 141219.10.1016/j.msea.2021.141219 ↗
22. U. Mitsutoshi, O. Jumpei, Y. Tatsumi, and T. Masao, The Effect of Microstructure on Steam Oxidation Behavior of the Fe–20Cr–35Ni–2.5Nb (at.%) Steel at 1073 K [J], Oxidation of Metals, 2021, 96, p 81–91.10.1007/s11085-021-10050-x ↗
23. Y. Chun, T.D. Nguyen, J. Zhang, and D.J. Young, Sulfur Effect on Corrosion Behavior of Fe-20Cr-(Mn, Si) and Fe-20Ni-20Cr-(Mn, Si) in CO2-H2O at 650 degrees C, J. Electrochem. Soc., 2016, 163(3), p C106–C115.10.1149/2.0751603jes ↗
24. K. Park, B. Cho, S.J. Hong, K.R. Lim, C. Lee, and G. Song, Outstanding High-Temperature Strength of Novel Fe–Cr–Ni–Al–V Ferritic Alloys with Hierarchical B2–NiAl Precipitates, Mater. Sci. Eng.: A, 2022, 840, 142999.10.1016/j.msea.2022.142999 ↗
25. X. Zhou, H. Dong, Y. Wang, and M. Yuan, (165612) Microstructure Characteristics and Mechanical Performance of Fe-Cr-Ni-Al-Ti Superalloy Fabricated by Powder Metallurgy, J. Alloy. Compd., 2022, 918, 165612.10.1016/j.jallcom.2022.165612 ↗
26. P. Van Trinh, J. Lee, B. Kang, P.N. Minh, D.D. Phuong, and S.H. Hong, Mechanical and Wear Properties of SiCp/CNT/Al6061 Hybrid Metal Matrix Composites, Diamond and Related Mater., 2022, 124, 108952.10.1016/j.diamond.2022.108952 ↗
27. V. Oddone and S. Reich, Thermal Properties of Metal Matrix Composites with Planar Distribution of Carbon Fibres, Physica Status Solidi-Rapid Res. Lett., 2017, 11(6), p 1700090.10.1002/pssr.201700090 ↗
28. M. Okumuş and B. Bülbül, Study of Microstructural, Mechanical, Thermal and Tribological Properties of Graphene Oxide Reinforced Al–10Ni Metal Matrix Composites Prepared by Mechanical Alloying Method, Wear, 2022, 510–511, 204511.10.1016/j.wear.2022.204511 ↗
29. J. Jin, Y. Wei, Y. Ji, Z. Zhang, G. Shi, Q. Li, D. Li, and Z. Wang, Synthesis and Strengthening Mechanism of (Ti09Nb003Ta003W003)3SiC2/Al2O3 Composite Ceramics by Doping NbC, TaC and WC Powders, Vacuum, 2023, 215, 112346.10.1016/j.vacuum.2023.112346 ↗
30. X. Wenbin, T. Huang, S. Huang, and Y. Zhuang, Regulation Mechanism of Magnetic Field on Non-Newtonian Melting and Energy Storage Performance of Metal Foam Composite Nano-Enhanced Phase Change Materials, Int. J. Heat and Mass Transf., 2023, 200, 123501.10.1016/j.ijheatmasstransfer.2022.123501 ↗
31. X. Tang, S. Shen, G. Chen, and T. Tao, High Temperature Wear Resistance of Tungsten Carbide Particle Reinforced Intermetallic Compound Matrix Composite by In-Situ Thermite Reaction, J. Market. Res., 2022, 19, p 4171–4176.
32. T. Chen, J.M. Hampikian, N.N. Thadhani, and Z.L. Wang, Structural Stability of Nanocrystalline NiAl, Microsc. Microanal., 1998, 4(S2), p 720–721.10.1017/S1431927600023722 ↗
33. Bo. Li, H. Guo, C. Li, Y. Gao, L. Feng, Y. Pan, and C. Liang, Microstructure, Mechanical Properties and High Temperature Tribological Behavior of NiAl-Based Composites, J. Market. Res., 2022, 20, p 3255–3263.
34. L. Wang, K.C. Lai, Li. Huang, J.W. Evans, and Y. Han, Low-Index Surface Energies, Cleavage Energies, and Surface Relaxations for Crystalline NiAl from First-Principles Calculations, Surf. Sci., 2020, 695, 121532.10.1016/j.susc.2019.121532 ↗
35. M. Kapoor, D. Isheim, G. Ghosh, S. Vaynman, M.E. Fine, and Y.-W. Chung, Aging Characteristics and Mechanical Properties of 1600 MPa Body-Centered Cubic Cu and B2-NiAl Precipitation-Strengthened Ferritic Steel, Acta Mater., 2014, 73(4), p 56–74.10.1016/j.actamat.2014.03.051 ↗
36. C.H. Liebscher, V.R. Radmilović, U. Dahmen, N.Q. Vo, D.C. Dunand, M. Asta and G. Ghosh, A Hierarchical Microstructure due to Chemical Ordering in the Bee Lattice: Early Stages of Formation in a Feritic Fe-A1-Cr-Ni-Ti alloy, Acta Mater., 2015, 92, p 220–232.10.1016/j.actamat.2015.03.043 ↗
37. B.K. Sahoo, V.C. Srivastava, A.K. Chandan and S.G. Chowdhury, Enhancing the Properties of Al–Ni Added Medium Mn Steel by Tailoring B2–NiAl Precipitates Through Aging Treatment, Mater. Sci. Eng. A, 2022, 837, p 142757.10.1016/j.msea.2022.142757 ↗
38. Y. Bai, J. Zhou, J. Li, and Z. Yang, B2-ORDERED NIAL Content on Microstructure, Mechanical and Oxidation Properties of FeAl Intermetallic Compounds, J. Market. Res., 2021, 16, p 1875–1888.
39. GB/T 1423-1996. Test Method for Density of Precious Metals and Their Alloys. (China Standard GB/T 1423-1996), 1997.
40. Q. Jia, X. An, H. Zhao, Fu. Haitao, H. Zhang, and X. Yang, Compaction and Solid-State Sintering of Tungsten Powders: MPFEM Simulation and Experimental Verification, J. Alloy. Compd., 2018, 750, p 341–349.10.1016/j.jallcom.2018.03.387 ↗
41. S. Li, X. Yang, J. Hou, and Du. Wenbo, A Review on Thermal Conductivity of Magnesium and its Alloys, J. Magnesium and Alloys, 2020, 8(1), p 78–90.10.1016/j.jma.2019.08.002 ↗
42. R. Ghanbari and G. Rashedi, The Wiedemann—Franz Law in a Normal Metal—Superconductor Junction, Chin. Phys. B, 2011, 20(12), 127401.10.1088/1674-1056/20/12/127401 ↗
43. G. Wang and Y. Li, Effects of Alloying Elements and Temperature on Thermal Conductivity of Ferrite, J. Appl. Phys., 2019, 126(12), 125118.10.1063/1.5115441 ↗
44. M.A. Benali, H. Tabet Derraz, I. Ameri, A. Bourguig, A. Neffah, R. Miloua, I.E. Yahiaoui, M. Ameri, and Y. Al-Douri, Synthesis and Analysis of SnO2/ZnO Nanocomposites: Structural Studies and Optical Investigations with Maxwell-Garnett Model, Mater. Chem. Phys., 2020, 240, p 122254.10.1016/j.matchemphys.2019.122254 ↗
45. C.-Y. Chuang, J.-W. Lee, C.-L. Li, and J.P. Chu, Mechanical Properties Study of a Magnetron-Sputtered Zr-based thin Film Metallic Glass, Surf. Coat. Technol., 2013, 215, p 312–321.10.1016/j.surfcoat.2012.04.101 ↗
46. Z.B. Jiao, J.H. Luan, M.K. Miller, C.Y. Yu, and C.T. Liu, Effects of Mn Partitioning on Nanoscale Precipitation and Mechanical Properties of Ferritic Steels Strengthened by NiAl Nanoparticles, Acta Mater., 2015, 84, p 283–291.10.1016/j.actamat.2014.10.065 ↗
47. R. Jia, W. Zeng, S. He, X. Gao, and Xu. Jianwei, The Analysis of Fracture Toughness and Fracture Mechanism of Ti60 Alloy Under Different Temperatures, J. Alloy. Compd., 2019, 810, 151899.10.1016/j.jallcom.2019.151899 ↗
48. T. Al-Mulla, R.J.-M. Pellenq, and F.-J. Ulm, Griffith’s Postulate: Grand Canonical Monte Carlo Approach for Fracture Mechanics of Solids, Eng. Fracture Mech., 2018, 199, p 544–554.10.1016/j.engfracmech.2018.06.001 ↗