Aging Temperature Effects on the Wear and Corrosion Properties of Stainless Steel Alloy Custom 450
Source abstract
Abstract
This article aims to investigate aging temperature effects on the wear and corrosion characteristics of stainless steel alloy Custom 450. Electrochemical measurements were performed in 1 M H2SO4 solution. Pin-on-disk tests and microstructural evaluations were also done. The results displayed that the steel hardness increased when the aging temperature was raised to 500 °C. However, higher temperatures resulted in a hardness reduction of about 11% compared with annealed specimens. Such observation was due to the increase in the reversed austenite content by up to 10.7%. The aged specimen’s wear rate was reduced by about 85% when the aging temperature was 500 °C, based on the high hardness. The suggested wear mechanism changed from abrasive and cutting wear mode to the adhesive wear mechanism when the aging temperature increased. Tafel polarization tests showed that corrosion rates of specimens decreased by about 99% when the aging temperature increased to 600 °C. This was attributed to increasing the amount of the reversed austenite phase, and Ni-rich precipitates in the aged martensite matrix.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. A. Salarvand, E. Poursaiedi, and A. Azizpour, Probability Approach for Prediction of Pitting Corrosion Fatigue Life of Custom 450 Steel, Int. J. Eng. Trans. A Basics, 2018, 31(10), p 1773–1781.
2. C.X. Li and T. Bell, Corrosion Properties of Plasma Nitrided AISI 410 Martensitic Stainless Steel in 3.5% NaCl and 1% HCl Aqueous Solutions, Corros. Sci., 2006, 48, p 2036–2049.10.1016/j.corsci.2005.08.011 ↗
3. J.L. Tian, W. Wang, M. Babar Shahzad, W. Yan, Y.Y. Shan, Z.H. Jiang, and K. Yang, Corrosion Resistance of Co-Containing Maraging Stainless Steel, Acta Metall. Sin., 2018, 31, p 785–797.10.1007/s40195-018-0758-9 ↗
4. G. Bellanger and J.J. Rameau, Effect of Slightly Acid pH with or Without Chloride in Radioactive Water on the Corrosion of Maraging Steel, J. Nucl. Mater., 1996, 228, p 24–37.10.1016/0022-3115(95)00218-9 ↗
5. T. Poornima, J. Nayak, and A. Nityananda Shetty, Corrosion of Aged and Annealed 18 Ni 250 Grade Maraging Steel in Phosphoric Acid Medium, Int. J. Electrochem. Sci., 2010, 5, p 56–71.10.1016/S1452-3981(23)15267-9 ↗
6. A. Strakosova, J. Kubasek, A. Michalcova, F. Prusa, D. Vojtech, and D. Dvorsky, High Strength X3NiCoMoTi 18-9-5 Maraging Steel Prepared by Selective Laser Melting from Atomized Powder, Materials, 2019, 12, p 4174.10.3390/ma12244174 ↗
7. T. Poornima, N. Jagannatha, and A. Nityananda Shetty, Studies on Corrosion of Annealed and Aged 18 Ni 250 Grade Maraging Steel in Sulphuric Acid Medium, Portugaliae Electrochim. Acta, 2010, 28(3), p 173–188.10.4152/pea.201003173 ↗
8. A.F. Avelino, W.S. Araujo, D.F. Dias, L.P.M. Santos, A.N. Correia, and P. Lima-Neto, Corrosion Investigation of the 18Ni 300 Grade Maraging Steel in Aqueous Chloride Medium Containing H2S and CO2, Electrochim. Acta, 2018, 286, p 339–349.10.1016/j.electacta.2018.08.042 ↗
9. B.S. Sanatkumar, J. Nayak, and A.N. Shetty, Corrosion Behavior of 18% Ni M250 Grade Maraging Steel Under Weld-Aged Condition in Sulfuric Acid Medium, Chem. Eng. Commun., 2012, 199(12), p 1610–1625.10.1080/00986445.2012.677879 ↗
10. P. Kumar and A.N. Shetty, Electrochemical Investigation on the Corrosion of 18%Ni M250 Grade Maraging Steel Under Welded Condition in Sulfuric Acid Medium, Surf. Eng. Appl. Electrochem., 2013, 49(3), p 76–83.10.3103/S1068375513030083 ↗
11. C. Man, C. Dong, D. Kong, L. Wang, and X. Li, Beneficial Effect of Reversed Austenite on the Intergranular Corrosion Resistance of Martensitic Stainless Steel, Corros. Sci., 2019, 151, p 108–121.10.1016/j.corsci.2019.02.020 ↗
12. A.H. Seikh, H. Halfa, M. Baig, and S.M.A. Khan, Microstructure Characterization and Corrosion Resistance Behavior of New Cobalt-Free Maraging Steel Produced Through ESR Techniques, J. Mater. Eng. Perform., 2017, 26(4), p 1589–1597.10.1007/s11665-017-2568-z ↗
13. H.N. Farneze, S.S.M. Tavares, J.M. Pardal, C. Barbosa, O.C. Pereira, and R.P.C. Cunha, Effects of Aging at 450 °C on the Pitting Corrosion Resistance and Toughness of AISI 317L Steel Welded by GTAW and FSW, Mater. Res., 2017, 20, p 621–629.10.1590/1980-5373-mr-2016-1007 ↗
14. L.P.M. Santos, M. Beres, I.N. Bastos, S.S.M. Tavares, H.F.G. Abreu, and M.J. Gomes da Silva, Hydrogen Embrittlement of Ultra-High Strength 300 Grade Maragingsteel, Corros. Sci., 2015, 101, p 12–18.10.1016/j.corsci.2015.06.022 ↗
15. J. Tian, W. Wang, M. Babar Shahzad, W. Yan, Y. Shan, Z. Jiang, and K. Yang, A new Maraging Stainless Steel with Excellent Strength–Toughness–Corrosion Synergy, Materials, 2017, 10, p 1293.10.3390/ma10111293 ↗
16. S. Chenna Krishna, J. Srinath, A.K. Jha, B. Pant, S.C. Sharma, and K.M. George, Effect of Heat Treatment on Microstructure and Mechanical Properties of 12Cr-10Ni-0.25Ti-0.7Mo Stainless Steel, Metallogr. Microstruct. Anal., 2013, 2, p 234–241.10.1007/s13632-013-0079-3 ↗
17. J. Edwin Bridge and G.N. Maniarm, Effect of Reverted Austenite on the Mechanical Properties and Toughness of a High Strength Maraging Stainless Steel Custom 450, Springer, Boston, 1980, p 279–295.
18. Y. Su, Z. Wei, G. Li, X. Zhang, H. Ci, and Y. Zhi, Effect of Reversed Austenite on Mechanical Properties of ZG06Cr13Ni4Mo Repair Welded Joint, Coatings, 2022, 12, p 1–15.10.3390/coatings12010001 ↗
19. M. Mat Noh, F. Mozafari, M. Adil Khattak, and M.N. Tamin, Effect of Pitting Corrosion on Strength of AISI 410 Stainless Steel Compressor Blades, Appl. Mech. Mater., 2014, 606, p 227–231.10.4028/www.scientific.net/AMM.606.227 ↗
20. Z. Jiang, H. Feng, H. Li, H. Zhu, S. Zhang, B. Zhang, Y. Han, T. Zhang, and D. Xu, Relationship Between Microstructure and Corrosion Behavior of Martensitic High Nitrogen Stainless Steel 30Cr15Mo1N at Different Austenitizing Temperatures, Materials, 2017, 10, p 861.10.3390/ma10080861 ↗
21. Y. Liu, Y. Dong, Y. Qi-Long, S. Jie, Z. Kun-Yu, and J. Wen, Effect of Heat Treatment on Microstructure and Property of Cr13 super Martensitic Stainless Steel, Int. J. Iron Steel Res., 2011, 18(11), p 60–66.10.1016/S1006-706X(11)60118-0 ↗
22. U.K. Viswanathan, S. Banerjee, and R. Krishnan, Effects of Aging on the Microstructure of 17–4 PH Stainless Steel, Mater. Sci. Eng. A, 1988, 104, p 181–189.10.1016/0025-5416(88)90420-X ↗
23. X.G. Peng, X.G. Zhou, X.Z. Hua, Z.G. Wei, and H.G. Liu, Effect of Aging on Hardening Behavior of 15–5 PH Stainless Steel, J. Iron. Steel Res. Int., 2015, 22(7), p 607–614.10.1016/S1006-706X(15)30047-9 ↗
24. S.Y. Lu, K.F. Yao, Y.B. Chen, M.H. Wang, Y. Shao, and X.Y. Ge, Effects of Austenitizing Temperature on the Microstructure and Electrochemical Behavior of a Martensitic Stainless Steel, J. Appl. Electrochem., 2015, 45, p 375–383.10.1007/s10800-015-0796-1 ↗
25. L. Couturier, F.D. Geuser, M. Descoins, and A. Deschamps, Evolution of the Microstructure of a 15–5PH Martensitic Stainless Steel During Precipitation Hardening Heat Treatment, Mater. Des., 2016, 107, p 416–425.10.1016/j.matdes.2016.06.068 ↗
26. S. Hahn, S. Isserow, and R. Ray, Microstructures and Mechanical Properties of boride-Dispersed Precipitation-Hardening Stainless Steels Produced by RST, J. Mater. Sci., 1987, 22, p 3395–3401.10.1007/BF01161211 ↗
27. B. Salehnasab, H. Zateajam, and S.M. Mousavi, Failure Analysis of a C450 Stainless Steel Blade in a Compressor, Int. J. Sci. Res., 2014, 2(1), p 143–150.
28. A. Salarvand, E. Poursaiedi, and A. Azizpour, Probability Approach for Prediction of Pitting Corrosion Fatigue Life of Custom 450 Steel, IJE Trans. A Basics, 2018, 31(10), p 1773–1781.
29. M. Azadi, M. Zolfaghari, S. Rezanezhad, and M. Azadi, Effects of SiO2 Nano-Particles on Tribological and Mechanical Properties of Aluminum Matrix Composites by Different Dispersion Methods, Appl. Phys. A, 2018, 124(5), p 377.10.1007/s00339-018-1797-9 ↗
30. F. Kamali and M. Azadi, An Evaluation of Tribological and Mechanical Properties of Al-Si-Cu Alloy with Nano-Clay Particles Reinforcement, Proc. Inst. Mech. Eng. C J. Mech. Eng. Sci., 2019, 233, p 7062–7076.10.1177/0954406219869746 ↗
31. A. Damula, C. Richard, and A. Igual-Munoz, Degradation Mechanisms in Martensitic Stainless Steels: Wear, Corrosion and Tribocorrosion Appraisal, Tribol. Int., 2018, 121, p 167–179.10.1016/j.triboint.2018.01.036 ↗
32. R. Puli and G.D. Janaki Ram, Wear and Corrosion Performance of AISI 410 Martensitic Stainless Steel Coatings Produced Using Friction Surfacing and Manual Metal Arc Welding. Surf. Coat. Technol., 2012, 209, p 1–7.
33. M. Mollaei, M. Azadi, and H. Tavakoli, A Parametric Study on Mechanical Properties of Aluminum–Silicon/SiO2 Nano-Composites by a Solid–Liquid Phase Processing, Appl. Phys. A, 2018, 124(7), p 504.10.1007/s00339-018-1929-2 ↗
34. S.B. Lyon and D. Feron, Overvew of Corrosion Science, Engineering, and Technology, Nuclear Corrosion Science and Engineering Woodhead Publishing, 2012.
35. A.A. Tiamiyu, U. Eduok, J.A. Szpunar, and A.G. Odeshi, Corrosion Behavior of Metastable AISI 321 Austenitic Stainless Steel: Investigating the Effect of Grain size and Prior Plastic Deformation on Its Degradation Pattern in Saline Media, Sci. Rep., 2019, 9, p 12116.10.1038/s41598-019-48594-3 ↗
36. M. Arab, M. Azadi, and O. Mirzaee, Effects of Manufacturing Parameters on the Corrosion Behavior of Al–B4C Nanocomposites, Mater. Chem. Phys., 2020, 253, p 123259.10.1016/j.matchemphys.2020.123259 ↗
37. M.A. Bidi, M. Azadi, and M. Rassouli, An Enhancement on Corrosion Resistance of Low Carbon Steel by a Novel Bio-Inhibitor (Leech Extract) in the H2SO4 Solution, Surf. Interfaces, 2021, 24, p 101159.10.1016/j.surfin.2021.101159 ↗
38. M. Watkins and J.B. Greer, Corrosion Testing of Highly Alloyed Materials for Deep, Sour Gas Well Environments, J. Pet. Technol., 1976, 28, p 698–704.10.2118/5622-PA ↗
39. H. Chen, T. Zeng, Q. Shi, N. Wang, S. Zhang, K. Yang, W. Yan, and W. Wang, Microstructure Evolution and Mechanical Properties During Long-Term Tempering of a Low Carbon Martensitic Stainless Bearing Steel, J. Market. Res., 2023, 25, p 297–309.
40. B.B. Yang, Y.Y. Song, L. Shi, H.C. Jiang, and L.J. Rong, Microstructure and corrosion resistance of low carbon martensitic stainless steel 0Cr13Ni4Mo with 3% Cu addition, Acta Metall. Sin., 2023