Investigation into Burnishing Process to Examine Effect on Surface Integrity, Wear and Corrosion Resistance of Carbon Alloy (EN31) Steel
Source abstract
Abstract
Residual stress and surface finish are prominent members responsible for service attributes of component, like wear resistance, corrosion resistance and fatigue life. This leads to investigate ball burnishing as a supplementary process to enhance durability of component. Burnishing is a well-known, inexpensive yet powerful superfinishing process that includes plastic deformation of surface layer, resulting in cold working which improves mechanical properties and extend components operational life. The aim of the current examination is to investigate and optimize ball burnishing process by Taguchi integrated PCA technique for finding most feasible combination of process variables to decrease specific wear rate and increase corrosion resistance of EN31 steel components. Post-burnishing, hardness improved from 178.5 to 265 Hv and roughness of surface reduced from 0.439 to 0.091 μm. The optimization findings revealed that 52% improvement in wear resistance as compared to the turned surface. X-ray diffraction shows that compressive residual stress was induced exactly under the burnished surface. The observed polarization curves and surface micrographs demonstrate that corrosion resistance is improved and consistent. The results confirm that ball burnishing technique enhanced the functional properties of EN31 steel.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Erosion and Abrasive Machining · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. L.M. Wagner, M. Mhaede, M. Wollmann, I. Altenberger, and Y. Sano, Surface Layer Properties and Fatigue Behavior in Al 7075–T73 and Ti-6Al-4V: Comparing Results After Laser Peening Shot Peening and Ball-Burnishing, Int. J. Struct. Integr., 2011, 22, p 185–199.10.1108/17579861111135923 ↗
2. K. Han, L. Tan, C. Yao, D. Zhang, and Z. Zhou, Studies on the Surface Characteristics of Ti60 Alloy Induced by Turning Combined with Ball Burnishing, J. Manuf. Process., 2022, 76, p 349–364.10.1016/j.jmapro.2022.02.019 ↗
3. J.A. Travieso-Rodríguez, R. Jerez-Mesa, G. Gómez-Gras, J. Llumà-Fuentes, O. Casadesús-Farràs, and M. Madueño-Guerrero, Hardening Effect and Fatigue Behavior Enhancement Through Ball Burnishing on AISI 1038, J. Mater. Res. Technol., 2019, 8, p 5639–5646.10.1016/j.jmrt.2019.09.032 ↗
4. R. Harish, D. Shivalingappa, G. Giridhar, and H. Hanumantharaju, Low Plasticity Burnishing Surface Treatment: Impact on Surface Integrity Parameters of Turned Cylindrical Ti- 6Al-4V Specimen, Austra. J. Mech. Engg., 2022 https://doi.org/10.1080/14484846.2022.207846910.1080/14484846.2022.2078469 ↗
5. X. Yuan, Y. Sun, C. Li, and W. Liu, Experimental Investigation into the Effect of Low Plasticity Burnishing Parameters on the Surface Integrity of Ta2, Int. J. Adv. Manuf. Technol., 2017, 88, p 1089–1099.10.1007/s00170-016-8838-3 ↗
6. P. Zhang, G. Ji, T. Lv, S. Hu, B. Wang, and Z. Liu, The Influence of Turning and Burnishing on Corrosion Resistance of Laser Cladded Fe-Cr-Ni Layer from Viewpoints of Thermodynamics and Kinetics, Arch. Civ. Mech. Eng., 2023, 23, p 164.10.1007/s43452-023-00698-4 ↗
7. B. Buldum and S. Cagan, Study of Ball Burnishing Process on the Surface Roughness and Microhardness of AZ91D Alloy, Exper. Tech., 2018, 42, p 233–241.10.1007/s40799-017-0228-8 ↗
8. A. Saldaña-robles, H. Plascencia-mora, A. Saldaña-robles, A. Marquez-Herrera, and J. Diosdado-De la Peña, Influence of Ball-Burnishing on Roughness, Hardness and Corrosion Resistance of AISI 1045 Steel, Surf. Coat. Technol., 2018, 339, p 191–198.10.1016/j.surfcoat.2018.02.013 ↗
9. G.V. Duncheva, J.T. Maximov, A.P. Anchev, V.P. Dunchev, Y.B. Argirov, and M. Kandeva-Ivanova, Enhancement of the Wear Resistance of CuAl9Fe4 Sliding Bearing Bushings via Diamond Burnishing, Wear, 2022, 510, p 204491.10.1016/j.wear.2022.204491 ↗
10. R. Avilés, J. Albizuri, A. Rodríguez, and L.N. López de Lacalle, Influence of Low-Plasticity Ball Burnishing on the High-Cycle Fatigue Strength of Medium Carbon AISI 1045 Steel, Int. J. Fatigue, 2013, 55, p 230–244.10.1016/j.ijfatigue.2013.06.024 ↗
11. R. Teimouri and S. Amini, A Comprehensive Optimization of Ultrasonic Burnishing Process Regarding Energy Efficiency and Workpiece Quality, Surf. Coat. Technol., 2019, 375, p 229–242.10.1016/j.surfcoat.2019.07.038 ↗
12. N.J. Varpe, A. Hamilton, and U. Gurnani, Review of Effect of Burnishing Process on Surface Integrity of Friction Stir Welded Components, Des. Eng., 2021, 04, p 651–666.
13. J. Caudill, J. Schoop, and I. Jawahir, Correlation of Surface Integrity with Processing Parameters and Advanced Interface Cooling/Lubrication in Burnishing of Ti-6Al-4V Alloy, Adv. Mater. Process. Technol., 2018, 5, p 53–66.
14. N.J. Varpe, A. Hamilton, and U. Gurnani, Optimization of Burnishing Process by Taguchi Method for Surface Enhancement of EN31 Steel, Surf. Topogr. Metrol. Prop., 2022, 10, p 015017.10.1088/2051-672X/ac4f37 ↗
15. Z. Zhen-yu, Z. Qiu-yang, D. Cong, Y. Ju-yu, and P. Zhong-yu, Effect of Surface Burnishing Process with Different Strain Paths on the Copper Microstructure, J. Manuf. Process., 2021, 71, p 653–668.10.1016/j.jmapro.2021.09.058 ↗
16. F. Gharbi, S. Sghaier, K.J. Al-Fadhalah, and T. Benameur, Effect of Ball Burnishing Process on the Surface Quality and Microstructure Properties of AISI 1010 Steel Plates, J. Mater. Eng. Perform., 2011, 20, p 903–910.10.1007/s11665-010-9701-6 ↗
17. C. Courbon, A. Sova, F. Valiorgue, H. Pascal, J. Sijobert, G. Kermouche, P. Bertrand, and J. Rech, Near Surface Transformations of Stainless Steel Cold Spray and Laser Cladding Deposits after Turning and Ball-Burnishing, Surf. Coat. Technol., 2019, 371, p 235–244.10.1016/j.surfcoat.2019.01.092 ↗
18. T. Zhang, N. Bugtai, and I.D. Marinescu, Burnishing of Aerospace Alloy: A Theoretical–Experimental Approach, J. Manuf. Syst., 2015, 37, p 472–478.10.1016/j.jmsy.2014.11.004 ↗
19. R. Kluz, M. Bucior, A. Dzierwa, K. Antosz, W. Bochnowski, and K. Ochał, Effect of Diamond Burnishing on the Properties of FSW Joints of EN AW-2024 Aluminum Alloys, Appl. Sci., 2023, 13, p 1305.10.3390/app13031305 ↗
20. G.D. Revankar, R.S. Shetty, S. Rao, and V. Gaitonde, Analysis of Surface Roughness and Hardness in Ball Burnishing of Titanium Alloy, Measurement, 2014, 58, p 256–268.10.1016/j.measurement.2014.08.043 ↗
21. W. Jiatian, Z. Changsheng, S. Xuehui, and H. Jianqun, A Study on Surface Integrity of Laser Cladding Coatings Post-treated by Ultrasonic Burnishing Coupled with Heat Treatment, Mater. Lett., 2022, 308, p 131136.10.1016/j.matlet.2021.131136 ↗
22. S. Świrad, D. Wydrzynski, P. Nieslony, and G.M. Krolczyk, Influence of Hydrostatic Burnishing Strategy on the Surface Topography of Martensitic Steel, Measurement, 2019, 138, p 590–601.10.1016/j.measurement.2019.02.081 ↗
23. J. Kalisz, K. Żak, S. Wojciechowski, M.K. Gupta, and G.M. Krolczyk, Technological and Tribological Aspects of Milling-Burnishing Process of Complex Surfaces, Tribol. Int., 2021, 155, p 106770.10.1016/j.triboint.2020.106770 ↗
24. S. Attabi, A. Himour, L. Laouar, and A. Motallebzadeh, Mechanical and Wear Behaviors of 316L Stainless Steel after Ball Burnishing Treatment, J. Mater. Res. Technol., 2021, 15, p 3255–3267.10.1016/j.jmrt.2021.09.081 ↗
25. E. Velázquez-Corral, V. Wagner, R. Jerez-Mesa, K. Delbé, and J. Llumà, Wear Resistance and Friction Analysis of Ti6Al4V Cylindrical Ball-Burnished Specimens with and Without Vibration Assistance, J. Adv. Manuf. Technol. Int., 2023 https://doi.org/10.1007/s00170-023-10919-y10.1007/s00170-023-10919-y ↗
26. K. Zaleski, and A. Skoczylas, Effect of Slide Burnishing on the Surface Layer and Fatigue Life of Titanium Alloy Parts, Adv. Mater. Sci., 2019, 19, p 35–45.10.2478/adms-2019-0020 ↗
27. M. Ozer, K. Dalli, and A. Ozer, Effect of Ball-Burnishing on Surface Integrity and Fatigue Behaviour of 7175–T6 AA, Mater. Sci. Technol., 2022, 39, p 248–257.10.1080/02670836.2022.2142744 ↗
28. Y. Hua, Z. Liu, B. Wang, and J. Jiang, Residual Stress Regenerated on Low Plasticity Burnished Inconel 718 Surface After Initial Turning Process, J. Manuf. Sci. Eng., 2019, 141, p 121004.10.1115/1.4045060 ↗
29. Z. Yuan, Z. Zhou, Z. Jiang, Z. Zhao, C. Ding, and Z. Piao, Evaluation of Surface Roughness of Aluminum Alloy in Burnishing Process Based on Chaos Theory, Chin. J. Mech. Eng., 2023, 36, p 801.10.1186/s10033-022-00828-8 ↗
30. J. Maximov, G. Duncheva, A. Anchev, V. Dunchev, Y. Argirov, and M. Nikolova, Effects of Heat Treatment and Diamond Burnishing on Fatigue Behaviour and Corrosion Resistance of AISI 304 Austenitic Stainless Steel, Appl. Sci., 2023, 13, p 2570.10.3390/app13042570 ↗
31. G. Jagadeesh and S. Setti, Tribological Performance Evaluation of Ball Burnished Magnesium Alloy for Bioresorbable Implant Applications, J. Mater. Eng. Perf., 2022, 31, p 1170–1186.10.1007/s11665-021-06228-8 ↗
32. M. Uddin, C. Hall, V. Santos, R. Visalakshan, G. Qian, and K. Vasilev, Synergistic Effect of Deep Ball Burnishing and HA Coating on Surface Integrity, Corrosion and Immune Response of Biodegradable AZ31B Mg Alloys, Mater. Sci. Eng. C, 2021, 118, p 111459.10.1016/j.msec.2020.111459 ↗
33. C. Cao, J. Zhu, T. Tanaka, and D. Pham, Investigation of Corrosion Resistance Enhancement for Biodegradable Magnesium Alloy by Ball Burnishing Process, Int. J. Autom. Technol., 2020, 14, p 175–183.10.20965/ijat.2020.p0175 ↗
34. P.J. Ross, Taguchi Techniques for Quality Engineering, Mc Graw-Hill, New York, 1996.
35. V. Barahate, A.R. Govande, G. Tiwari, B.R. Sunil, and R. Dumpala, Parameter Optimization during Single Roller Burnishing of AA6061-T6 Alloy by Design of Experiments, Mater. Today Proc., 2022, 50, p 1976–1970.
36. N.J. Varpe, R. Tajane, U. Gurnani, and A. Hamilton, Multi Objective Optimization of Burnishing to Eliminate Heat Treatment in Reamer Shank Manufacturing by Using Taguchi Coupled Principal Component Analysis (PCA), Adv. Mater. Process. Technol., 2022 https://doi.org/10.1080/2374068X.2022.211893110.1080/2374068X.2022.2118931 ↗
37. K. Pearson, On Lines and Planes of Closest Fit to Systems of Points in Spaces, Phil. Mag. Ser., 1901, 6, p 559–572.10.1080/14786440109462720 ↗
38. H. Hotelling, Analysis of a Complex of Statistical Variables into Principal Components, J. Educ. Psychol., 1933, 24, p 417–441.10.1037/h0071325 ↗
39. A. Torres, C. Amini, N. Cuadrado, J.A. Travieso-Rodriguez, J. Llumà, and M. Vilaseca, Experimental Validation of Ball Burnishing Numerical Simulation on Ball-end Milled Martensitic Stainless-Steel Considering Friction and the Initial Surface Topography, J. Mater. Res. Tech., 2023, 22, p 3352–3361.10.1016/j.jmrt.2022.12.100 ↗
40. J. Maximov, G. Duncheva, A. Anchev, N. Ganev, I. Amudjev, and V. Dunchev, Effect of Slide Burnishing Method on the Surface Integrity of AISI 316Ti Chromium–Nickel Steel, J. Braz. Soc. Mech. Sci. Eng., 2018, 40, p 194.10.1007/s40430-018-1135-3 ↗
41. J. Maximov, G. Duncheva, A. Anchev, and M. Ichkova, Slide burnishing-review and prospects, Int. J. Adv. Manuf. Technol., 2019, 104, p 785–801.10.1007/s00170-019-03881-1 ↗
42. Z. Pu, G.-L. Song, S. Yang, J.C. Outeiro, O.W. Dillon Jr., D.A. Puleo, and I.S. Jawahir, Grain Refined and Basal Textured Surface Produced by Burnishing for Improved Corrosion Performance of AZ31B Mg Alloy, Corros. Sci., 2012, 57, p 192–201.10.1016/j.corsci.2011.12.018 ↗
43. H. Hamadache, L. Laouar, N.E. Zeghib, and K. Chaoui, Characteristics of Rb40 Steel Superficial Layer Under Ball and Roller Burnishing, J. Mater. Process. Technol., 2006, 180, p 130–136.10.1016/j.jmatprotec.2006.05.013 ↗
44. A. Rami, F. Gharbi, S. Sghaier, and H. Hamdi, Some Insights on Combined Turning-Burnishing (CoTuB) Process on Workpiece Surface Integrity, Inter. J. Precis. Eng. Manuf., 2018, 19, p 67–78.10.1007/s12541-018-0008-0 ↗
45. R. Tajane and P. Pawar, Investigation into Burnishing to Minimize Heat Treatment in Drill Manufacturing, Mater. Manuf. Process., 2020, 35, p 817–825.10.1080/10426914.2020.1743848 ↗
46. S.C. Cagan, B.B. Buldum, and I. Ozkul, Experimental Investigation on the Ball Burnishing of Carbon Fiber Reinforced Polymer, Mater. Manuf. Process., 2019, 34, p 1062–1067.10.1080/10426914.2019.1615078 ↗
47. J. Travieso-Rodríguez, G. Gomez-Gras, and G. Dessein, Effects of a Ball-Burnishing Process Assisted by Vibrations in G10380 Steel Specimens, Int. J. Adv. Manuf. Technol., 2015, 81, p 1757–1765.10.1007/s00170-015-7255-3 ↗
48. G. Revankara, R. Shetty, S. Rao, and V. Gaitonded, Wear Resistance Enhancement of Titanium Alloy (Ti – 6Al – 4V) by Ball Burnishing Process, J. Mater. Res. Technol., 2017, 6, p 13–32.10.1016/j.jmrt.2016.03.007 ↗
49. A. Joseph Vimal, A. Bensely, D. Mohan Lal, and K. Srinivasan, Deep Cryogenic Treatment Improves Wear Resistance of En 31 Steel, Mater. Manuf. Process., 2008, 23, p 369–376.10.1080/10426910801938098 ↗
50. S. Swirad and P. Pawlus, The Effect of Ball Burnishing on Tribological Performance of 42CrMo4 Steel under Dry Sliding Conditions, Materials, 2020, 13, p 2127.10.3390/ma13092127 ↗
51. S. Sunny, R. Mathews, H. Yu, and A. Malik, Effects of Microstructure and Inherent Stress on Residual Stress Induced During Powder Bed Fusion with Roller Burnishing, Inter. J. Mech. Sci., 2022, 219, p 107092.10.1016/j.ijmecsci.2022.107092 ↗
52. H. Livatyali, E. Has, and M. Türköz, Prediction of Residual Stresses in Ball Burnishing TI6AL4V Thin Sheets, Inter. J. Adv. Manuf. Tech., 2020, 110, p 1083–1093.10.1007/s00170-020-05837-2 ↗
53. A. Alshareef, I. Marinescu, I. Basudan, B. Alqahtani, and M. Tharwan, Ball-Burnishing Factors Affecting Residual Stress of AISI 8620 Steel, Int. J. Adv. Manuf. Tech., 2020, 107, p 1387–1397.10.1007/s00170-020-05119-x ↗
54. P. Zhang and Z. Liu, Enhancing Surface Integrity and Corrosion Resistance of Laser Cladded Cr–Ni Alloys by Hard Turning and Low Plasticity Burnishing, Appl. Surf. Sci., 2017, 409, p 169–178.10.1016/j.apsusc.2017.03.028 ↗