Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy
Source abstract
Abstract
Ti6Al4V titanium alloy, due to its low thermal conductivity and high chemical reactivity, leads to severe tool wear during the cutting process. TiN/TiSiN possesses excellent thermal properties and hardness, which makes it a promising material for protecting tools. To investigate the cutting performance of TiN/TiSiN coated tools, a turning model was established by the finite element method and validated. Comprehensive analyses of cutting force, tool temperature, and tool stress were conducted, comparing the TiN/TiSiN coated tools’ data with uncoated tools, TiN coated tools, and TiSiN coated tools. The results showed that TiN/TiSiN coating did not change the cutting force significantly, the application of TiN/TiSiN coating resulted in an increase of 1.8%. The temperature of TiN/TiSiN coated tool substrate is decreased by approximately 10.2–15.6% compared to other tools at the same cutting parameters. Regarding tool stress of TiN/TiSiN coated tools, there is a reduction of 22.1–32.4% compared to tools with alternative coating. The results show that the application of TiN/TiSiN coating can improve the turning performance for Ti6Al4V. The research of this paper provides guidance for further study of exploring the wear mechanisms of TiN/TiSiN coated tools and determining optimal machining parameters.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced machining processes and optimization · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. A. Saini, B.S. Pabla, and S.S. Dhami, Developments in Cutting Tool Technology in Improving Machinability of Ti6Al4V Alloy: A Review, Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., 2016, 230(11), p 1977–1989. https://doi.org/10.1177/095440541664017610.1177/0954405416640176 ↗
2. N. Nadim, O.A. Shams, T.T. Chandratilleke, and A. Pramanik, Preheating and Thermal Behaviour of a Rotating Cylindrical Workpiece in Laser-Assisted Machining, Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., 2020, 234(3), p 559–570. https://doi.org/10.1177/095440541986359710.1177/0954405419863597 ↗
3. X.Z. Wang, Z.D. Liu, Z.G. Hui, M.B. Qiu, Z.J. Tian, and Z.L. Cao, Microcosmic Mechanism of Electrical Discharge Machining Ablation on Titanium Alloy, Int. J. Adv. Manuf. Technol., 2016, 83, p 929–935. https://doi.org/10.1007/s00170-015-7607-z10.1007/s00170-015-7607-z ↗
4. P. Ranjan and S.S. Hiremath, Role of textured tool in Improving Machining Performance: A Review, J. Manuf. Processes., 2019, 43, p 47–73. https://doi.org/10.1016/j.jmapro.2019.04.01110.1016/j.jmapro.2019.04.011 ↗
5. S.K. Pattnaik, N.K. Bhoi, S. Padhi, and S.K. Sarangi, Dry Machining of Aluminum for Proper Selection of Cutting Tool: Tool Performance and Tool Wear, Int. J. Adv. Manuf. Technol., 2018, 98, p 55–65. https://doi.org/10.1007/s00170-017-0307-010.1007/s00170-017-0307-0 ↗
6. F. Klocke, N. Michailidis, K.D. Bouzakis, M. Witty, S. Gerardis, E. Lili, and M. Pappa, Investigation of Coated Tools’ Cutting Performance in Milling Ti6Al4V and Its Correlation to the Temperature Dependent Impact Resistance of the Film, Prod. Eng., 2010, 4, p 509–514. https://doi.org/10.1007/s11740-010-0235-410.1007/s11740-010-0235-4 ↗
7. E.O. Ezugwu, R.B. Da Silva, J. Bonney, and A.R. Machado, Evaluation of the Performance of CBN Tools when Turning Ti–6Al–4V Alloy with High Pressure Coolant Supplies, Int. J. Mach. Tools Manuf, 2005, 45(9), p 1009–1014.10.1016/j.ijmachtools.2004.11.027 ↗
8. S. Koseki, K. Inoue, K. Sekiya, S. Morito, T. Ohba, and H. Usuki, Wear Mechanisms of PVD-Coated Cutting Tools During Continuous Turning of Ti-6Al-4V Alloy, Precis. Eng., 2017, 47, p 434–444.10.1016/j.precisioneng.2016.09.018 ↗
9. Y.X. Xu, L. Chen, Z.Q. Liu, F. Pei, and Y. Du, Improving Thermal Stability of TiSiN Nanocomposite Coatings by Multilayered Epitaxial Growth, Surf. Coat. Technol., 2017, 321, p 180–185. https://doi.org/10.1016/j.surfcoat.2017.04.05710.1016/j.surfcoat.2017.04.057 ↗
10. Q. Wan, B. Yang, H.D. Liu, J. Chen, and J. Zhang, Microstructure and Adhesion of MeN/TiSiN (Me= Ti, Cr, Zr, Mo, NbxAl1− x) Multilayered Coatings Deposited by Cathodic Arc Ion Plating, Appl. Surf. Sci., 2019, 497, 143602. https://doi.org/10.1016/j.apsusc.2019.14360210.1016/j.apsusc.2019.143602 ↗
11. Y. Moritz, C. Saringer, M. Tkadletz, A. Stark, N. Schell, I. Letofskt-Papst, C. Czettl, M. Pohler, and N. Schalk, Oxidation Behavior of Arc Evaporated TiSiN Coatings Investigated by In-Situ Synchrotron X-ray Diffraction and HR-STEM, Sur. Coat. Technol., 2020, 404, 126632. https://doi.org/10.1016/j.surfcoat.2020.12663210.1016/j.surfcoat.2020.126632 ↗
12. S. Imamura, H. Fukui, A. Shibata, N. Omori, and M. Setoyama, Properties and Cutting Performance of AlTiCrN/TiSiCN Bilayer Coatings Deposited by Cathodic-Arc Ion Plating, Surf. Coat. Technol., 2007, 202(4–7), p 820–825. https://doi.org/10.1016/j.surfcoat.2007.05.08710.1016/j.surfcoat.2007.05.087 ↗
13. S. Peng, J. Xu, P. Munroe, and Z. Xie, Sandwich-Structured, Damage-Resistant TiN/Graded TiSiN/TiSiN film, Results Phys., 2019, 12, p 543–554. https://doi.org/10.1016/j.rinp.2018.12.01910.1016/j.rinp.2018.12.019 ↗
14. A. Mège-Revil, P. Steyer, S. Cardinal, G. Thollet, G. Esnouf, P. Jacquot, and B. Stauder, Correlation Between Thermal Fatigue and Thermomechanical Properties During the Oxidation of Multilayered TiSiN Nanocomposite Coatings Synthesized by a Hybrid Physical/Chemical Vapour Deposition Process, Thin Solid Films, 2010, 518(21), p 5932–5937. https://doi.org/10.1016/j.tsf.2010.05.09210.1016/j.tsf.2010.05.092 ↗
15. P.C. Wo, X.L. Zhao, P.R. Munroe, Z.F. Zhou, K.Y. Li, D. Habibi, and Z.H. Xie, Extremely Hard, Damage-Tolerant Ceramic Coatings with Functionally Graded, Periodically Varying Architecture, Acta Mater., 2013, 61(1), p 193–204. https://doi.org/10.1016/j.actamat.2012.09.04910.1016/j.actamat.2012.09.049 ↗
16. Y.X. Xu, L. Chen, Z.Q. Liu, F. Pei, and Y. Du, Improving Thermal Stability of TiSiN Nanocomposite Coatings by Multilayered Epitaxial Growth, Surf. Coat. Technol., 2017, 321, p 180–185.10.1016/j.surfcoat.2017.04.057 ↗
17. I. Krajinović, W. Daves, M. Tkadletz, T. Teppernegg, T. Klünsener, N. Schalk, C. Mitterer, C. Tritremmel, W. Ecker, and C. Czettl, Finite Element Study of the Influence of Hard Coatings on Hard Metal Tool Loading During Milling, Surf. Coat. Technol., 2016, 304, p 134–141. https://doi.org/10.1016/j.surfcoat.2016.06.04110.1016/j.surfcoat.2016.06.041 ↗
18. F. Kara, K. Aslantas, and A. Çiçek, Prediction of Cutting Temperature in Orthogonal Machining of AISI 316L Using Artificial Neural Network, Appl. Soft Comput., 2016, 38, p 64–74. https://doi.org/10.1016/j.asoc.2015.09.03410.1016/j.asoc.2015.09.034 ↗
19. F.Z. Wang, J. Zhao, Z.L. Li, and A.H. Li, Coated Carbide Tool Failure Analysis in High-Speed Intermittent Cutting Process Based on Finite Element Method, Int. J. Adv. Manuf. Technol., 2016, 83, p 805–813. https://doi.org/10.1007/s00170-015-7632-y10.1007/s00170-015-7632-y ↗
20. F. Kara, K. Aslantas, and A. Çiçek, ANN and Multiple Regression Method-Based Modelling of Cutting Forces in Orthogonal Machining of AISI 316L Stainless Steel, Neural Comput. Appl., 2015, 26, p 237–250. https://doi.org/10.1007/s00521-014-1721-y10.1007/s00521-014-1721-y ↗
21. L. Tu, F. Xu, X. Wang, J.Y. Gao, S. Tian, M.F. Yuen, and D. Zuo, Temperature Distribution of Cubic Boron Nitride-Coated Cutting Tools by Finite Element Analysis, Int. J. Adv. Manuf. Technol., 2019, 105, p 3197–3207. https://doi.org/10.1007/s00170-019-04498-010.1007/s00170-019-04498-0 ↗
22. F. Kara, F. Bayraktar, F. Savaş, and O. Özbek, Experimental and Statistical Investigation of the Effect of Coating Type on Surface Roughness, Cutting Temperature, Vibration and Noise in Turning of Mold Steel, J. Mater. Manuf., 2023, 2(1), p 31–43. https://doi.org/10.5281/zenodo.802055310.5281/zenodo.8020553 ↗
23. T. Thepsonthi and T. Özel, Experimental and Finite Element Simulation Based Investigations on Micro-milling Ti-6Al-4V Titanium Alloy: Effects of cBN Coating on Tool Wear, J. Mater. Process. Technol., 2013, 213(4), p 532–542. https://doi.org/10.1016/j.jmatprotec.2012.11.00310.1016/j.jmatprotec.2012.11.003 ↗
24. M. Günay, M.E. Korkmaz, and N. Yaşar, Finite Element Modeling of Tool Stresses on Ceramic Tools in Hard Turning, Mechanics., 2017, 23(3), p 432–440. https://doi.org/10.5755/j01.mech.23.3.1436310.5755/j01.mech.23.3.14363 ↗
25. W. Grzesik, M. Bartoszuk, and P. Nieslony, Finite Element Modelling of Temperature Distribution in the Cutting Zone in Turning Processes with Differently Coated Tools, J. Mater. Process. Technol., 2005, 164, p 1204–1211. https://doi.org/10.1016/j.jmatprotec.2005.02.13610.1016/j.jmatprotec.2005.02.136 ↗
26. M. Sadeghifar, R. Sedaghati, W. Jomaa, and V. Songmene, Finite Element Analysis and Response Surface Method for Robust Multi-performance Optimization of Radial Turning of Hard 300M Steel, Int. J. Adv. Manuf. Technol., 2018, 94, p 2457–2474. https://doi.org/10.1007/s00170-017-1032-410.1007/s00170-017-1032-4 ↗
27. T. Mabrouki, F. Girardin, M. Asad, and J.F. Rigal, Numerical and Experimental Study of Dry Cutting for an Aeronautic Aluminium Alloy (A2024-T351), Int. J. Mach. Tools Manuf, 2008, 48(11), p 1187–1197. https://doi.org/10.1016/j.ijmachtools.2008.03.01310.1016/j.ijmachtools.2008.03.013 ↗
28. G.R. Johnson and W.H. Cook, Fracture Characteristics of Three Metals Subjected to Various Strains, Strain Rates, Temperatures and Pressures, Eng. Fract. Mech., 1985, 21(1), p 31–48. https://doi.org/10.1016/0013-7944(85)90052-910.1016/0013-7944(85)90052-9 ↗
29. Y. Xi, M. Bermingham, G. Wang, and M. Dargusch, Finite Element Modeling of Cutting Force and Chip Formation During Thermally Assisted Machining of Ti6Al4V Alloy, J. Manuf. Sci. Eng., 2013, 135(6), 061014. https://doi.org/10.1115/1.402574010.1115/1.4025740 ↗
30. G. Chen, C. Ren, X. Yang, and T. Guo, Finite Element Simulation of High-Speed Machining of Titanium Alloy (Ti-6Al-4V) Based on Ductile Failure Model, Int. J. Adv. Manuf. Technol., 2011, 56, p 1027–1038. https://doi.org/10.1007/s00170-011-3233-610.1007/s00170-011-3233-6 ↗
31. C.S. Kumar, P. Zeman, and T. Polcar, A 2D Finite Element Approach for Predicting the Machining Performance of Nanolayered TiAlCrN Coating on WC-Co Cutting Tool During Dry Turning of AISI 1045 Steel, Ceram. Int., 2020, 46(16), p 25073–25088. https://doi.org/10.1016/j.ceramint.2020.06.29410.1016/j.ceramint.2020.06.294 ↗
32. P. Ranjan and S.S. Hiremath, Finite Element Simulation and Experimental Validation of Machining Martensitic Stainless Steel Using Multi-layered Coated Carbide Tools for Industry-Relevant Outcomes, Simul. Model. Pract. Theory, 2022, 114, 102411. https://doi.org/10.1016/j.simpat.2021.10241110.1016/j.simpat.2021.102411 ↗
33. R. Tu, M.Q. Jiang, M. Yang, B.F. Ji, T.H. Gao, S. Zhang, and L.M. Zhang, Effects of Gradient Structure and Modulation Period on Mechanical Performance and Thermal Stress of TiN/TiSiN Multilayer Hard Coatings, Mater. Sci. Eng. A, 2023, 866, 144696. https://doi.org/10.1016/j.msea.2023.14469610.1016/j.msea.2023.144696 ↗
34. T. Özel and T. Altan, Determination of Workpiece Flow Stress and Friction at The Chip-Tool Contact for High-Speed Cutting, Int. J. Mach. Tools Manuf., 2000, 40(1), p 133–152. https://doi.org/10.1016/S0890-6955(99)00051-610.1016/S0890-6955(99)00051-6 ↗
35. W. Jomaa, O. Mechri, J. Lévesque, V. Songmene, P. Bocher, and A. Gakwaya, Finite Element Simulation and Analysis of Serrated Chip Formation During High-Speed Machining of AA7075–T651 Alloy, J. Manuf. Processes., 2017, 26, p 446–458. https://doi.org/10.1016/j.jmapro.2017.02.01510.1016/j.jmapro.2017.02.015 ↗
36. S.K. Mishra, S. Ghosh, and S. Aravindan, Performance of Laser Processed Carbide Tools for Machining of Ti6Al4V Alloys: A Combined Study on Experimental and Finite Element Analysis, Precis. Eng., 2019, 56, p 370–385. https://doi.org/10.1016/j.precisioneng.2019.01.00610.1016/j.precisioneng.2019.01.006 ↗
37. C.S. Kumar and S.K. Patel, Effect of Chip Sliding Velocity and Temperature on the Wear Behaviour of PVD AlCrN and AlTiN Coated Mixed Alumina Cutting Tools During Turning of Hardened Steel, Surf. Coat. Technol., 2018, 334, p 509–525. https://doi.org/10.1016/j.surfcoat.2017.12.01310.1016/j.surfcoat.2017.12.013 ↗
38. D. Zhang, X.M. Zhang, G.C. Nie, Z.Y. Yang, and H. Ding, Characterization of Material Strain and Thermal Softening Effects in the Cutting Process, Int. J. Mach. Tools Manuf, 2021, 160, 103672. https://doi.org/10.1016/j.ijmachtools.2020.10367210.1016/j.ijmachtools.2020.103672 ↗
39. Q. Wan, B. Yang, Y.M. Chen, Y. Cai, Y. Liu, L. Meng, and D.X. Gao, Effect of Bilayer Period on Microstructure and Mechanical Properties of TiSiN/TiN Coatings, Materialia., 2018, 3, p 260–264. https://doi.org/10.1016/j.mtla.2018.08.02710.1016/j.mtla.2018.08.027 ↗
40. M. Lee, High temperature hardness of tungsten carbide, Metall. Trans. A, 1983, 14, p 1625–1629. https://doi.org/10.1007/BF0265439010.1007/BF02654390 ↗
41. M.A. Shalaby and S.C. Veldhuis, Wear and Tribological Performance of Different Ceramic Tools in Dry High Speed Machining of Ni-Co-Cr Precipitation Hardenable Aerospace Superalloy, Tribol. Trans., 2019, 62(1), p 62–77. https://doi.org/10.1080/10402004.2018.148649410.1080/10402004.2018.1486494 ↗
42. P. Steyer, D. Pilloud, J.F. Pierson, J.P. Millet, M. Charnay, B. Stauder, and P. Jacquot, Oxidation resistance improvement of arc-evaporated TiN hard coatings by silicon addition, Surf. Coat. Technol., 2006, 201(7), p 4158–4162. https://doi.org/10.1016/j.surfcoat.2006.08.02310.1016/j.surfcoat.2006.08.023 ↗
43. L. Qiu, Y. Du, S.Q. Wang, K. Li, L. Yin, L.Y. Wu, Z.Q. Zhong, and L. Albri, Mechanical Properties and Oxidation Resistance of Chemically Vapor Deposited TiSiN Nanocomposite Coating with Thermodynamically Designed Compositions, Int. J. Refract. Met. Hard Mater., 2019, 80, p 30–39. https://doi.org/10.1016/j.ijrmhm.2018.12.01810.1016/j.ijrmhm.2018.12.018 ↗
44. A. Al-Rjoub, A. Cavaleiro, S.S. Rajput, and F. Fernandes, High Si Multilayered TiSiN/TiN (Ag) Films with Superior Oxidation Resistance, J. Mater. Res. Technol., 2021, 12, p 2340–2347. https://doi.org/10.1016/j.jmrt.2021.04.04010.1016/j.jmrt.2021.04.040 ↗
45. M. Weber, H. Autenrieth, J. Kotschenreuther, P. Gumbsch, V. Schulze, D. Löhe, and J. Fleischer, Influence of Friction and Process Parameters on the Specific Cutting Force and Surface Characteristics in Micro Cutting, Mach. Sci. Technol., 2008, 12(4), p 474–497. https://doi.org/10.1080/1091034080251872810.1080/10910340802518728 ↗
46. J.M. Zhou, M. Andersson, and J.E. Ståhl, Cutting Tool Fracture Prediction and Strength Evaluation by Stress Identification, Part I: Stress Model, Int. J. Mach. Tools Manuf, 1997, 37(12), p 1691–1714. https://doi.org/10.1016/S0890-6955(97)00031-X10.1016/S0890-6955(97)00031-X ↗
47. S. Guha, A. Bandyopadhyay, S. Das, and B.P. Swain, Synthesis and Characterization of Titanium Silicon Nitride (TiSiN) Thin Film: A Review, Mater. Sci. Eng., 2018, 377, 012181. https://doi.org/10.1088/1757-899X/377/1/01218110.1088/1757-899X/377/1/012181 ↗
48. M. Günay, M.E. Korkmaz, and N. Yaşar, Finite Element Modeling of Tool Stresses on Ceramic Tools in Hard Turning, Mechanics, 2017, 23(3), p 432–440. https://doi.org/10.5755/j01.mech.23.3.1436310.5755/j01.mech.23.3.14363 ↗