Dissolution and Coarsening Kinetics of γ′ Precipitates in Waspaloy during Solution Treatment at Temperatures of 1000-1045 °C
Source abstract
Abstract
Dissolution and coarsening characteristics of γ′ precipitates in Waspaloy were investigated during solution treatments in the temperature range of 1000-1045 °C. The γ′ precipitates decreased significantly within 10 min and then remained unchanged. The dissolution behavior was quantitatively studied using the Johnson–Mehl–Avrami–Kolmogorov model. The dissolution activation energy that increased gradually with the increase in holding time was evaluated using the classical Arrhenius equation. For the sub-solvus heat-treated samples, the coarsening of the γ′ precipitates was observed after 10 min. A Lifshitz–Slyozov–Wagner (LSW)-type relationship was found to quantify the coarsening process. A γ′-coarsening activation energy that was comparable to the activation energy for the diffusion of Al and Ti in Ni was obtained based on the LSW model. This result verifies that the coarsening of the γ′ precipitates was mainly controlled by the matrix-diffusion of the γ′-forming elements. Abnormal grain growth was formed at 1030 °C due to the relatively low pinning force of the few γ′ precipitates. The present work contributes to the kinetics and mechanism of the evolution of the γ′ precipitates during the solution treatments and provides reference for optimizing the microstructure.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. H.L. Liu, M.C. Zhang, M. Xu, Y. Meng, G.H. Xu, N. Ta and L. Zheng, Microstructure Evolution Dependence of Work-Hardening Characteristic in Cold Deformation of a Difficult-to-Deform Nickel-Based Superalloy, Mater. Sci. Eng. A, 2021, 800, p 140280. (in English)10.1016/j.msea.2020.140280 ↗
2. L. Zheng, G. Schmitz, Y. Meng, R. Chellali and R. Schlesiger, Mechanism of Intermediate Temperature Embrittlement of Ni and Ni-based Superalloys, Crit. Rev. Solid State, 2012, 37(3), p 181–214. (in English)10.1080/10408436.2011.613492 ↗
3. G. Yeli, D. Chen, K. Yabuuchi, A. Kimura, S. Liu, W. Lin, Y. Zhao, S. Zhao and J.J. Kai, The Stability of γ′ Precipitates in a Multi-Component FeCoNiCrTi0.2 Alloy Under Elevated-Temperature Irradiation, J. Nucl. Mater., 2020, 540, p 152364. (in English)10.1016/j.jnucmat.2020.152364 ↗
4. P. Zhang, Y. Yuan, J. Li, Y.F. Xu, X.L. Song and G.X. Yang, Tensile Deformation Mechanisms in a New Directionally Solidified Ni-base Superalloy Containing Coarse γ′ Precipitates at 650 °C, Mater. Sci. Eng. A, 2017, 702, p 343–349. (in English)10.1016/j.msea.2017.07.025 ↗
5. L. Shui, T. Jin, S. Tian and Z.Q. Hu, Influence of Precipitate Morphology on Tensile Creep of a Single Crystal Nickel-base Superalloy, Mater. Sci. Eng. A, 2007, 454, p 461–466. (in English)10.1016/j.msea.2006.11.136 ↗
6. M. Pouranvari, A. Ekrami and A.H. Kokabi, Microstructure Evolution Mechanism During Post-bond Heat Treatment of Transient Liquid Phase Bonded Wrought IN718 Superalloy: An Approach to Fabricate Boride-Free Joints, J. Alloy Compd., 2017, 723, p 84–91. (in English)10.1016/j.jallcom.2017.06.206 ↗
7. L.S. Araujo, D.S. dos Santos, S. Godet, J. Dille, A.L. Pinto and L.H. de Almeida, Analysis of Grain Boundary Character in a Fine-Grained Nickel-based Superalloy 718, J. Mater. Eng. Perform., 2014, 23(11), p 4130–4135. (in English)10.1007/s11665-014-1172-8 ↗
8. M. Rafiei, H. Mirzadeh and M. Malekan, Precipitation Kinetics of γ″ Phase and its Mechanism in a Nb-bearing Nickel-Based Superalloy During Aging, Vacuum, 2020, 2020(178), p 109456. (in English)10.1016/j.vacuum.2020.109456 ↗
9. R. Radis, M. Schaffer, M. Albu, G. Kothleitner, P. Pölt and E. Kozeschnik, Multimodal Size Distributions of γ′ Precipitates During Continuous Cooling of UDIMET 720 Li, Acta Mater., 2009, 57(19), p 5739–5747. (in English)10.1016/j.actamat.2009.08.002 ↗
10. A.J. Goodfellow, E.I. Galindo-Nava, K.A. Christofidou, N.G. Jones, T. Martin, P.A. Bagot, C.D. Boyer, M.C. Hardy and H.J. Stone, Gamma Prime Precipitate Evolution During Aging of a Model Nickel-based Superalloy, Metall. Mater. Trans. A, 2018, 49(3), p 718–728. (in English)10.1007/s11661-017-4336-y ↗
11. H. Wu, Z. Huang, N. Zhou, J. Chen, P. Zhou and L. Jiang, A Study of Solution Cooling Rate on γ′ Precipitate and Hardness of a Polycrystalline Ni-based Superalloy Using a High-Throughput Methodology, Mater. Sci. Eng. A, 2019, 739, p 473–479. (in English)10.1016/j.msea.2018.10.041 ↗
12. M. Ou, Y. Ma, H. Ge, B. Chen, S. Zheng and K. Liu, Effect of Long-term Aging on the Microstructure, Stress Rupture Properties and Deformation Mechanisms of a New Cast Nickel Base Superalloy, Mater. Sci. Eng. A, 2018, 736, p 76–86. (in English)10.1016/j.msea.2018.08.096 ↗
13. H. Huang, G. Liu, H. Wang, A. Ullah and B. Hu, Dissolution Behavior and Kinetics of γ′ Phase During Solution Treatment in Powder Metallurgy Nickel-based Superalloy, Metall. Mater. Trans. A, 2020, 51(3), p 1075–1084. (in English)10.1007/s11661-019-05581-7 ↗
14. Z. Wan, L. Hu, Y. Sun, T. Wang, Z. Li and Y. Zhang, Effect of Solution Treatment on Microstructure and Tensile Properties of a U720LI Ni-based Superalloy, Vacuum, 2018, 156, p 248–255. (in English)10.1016/j.vacuum.2018.07.041 ↗
15. C.Y. Cui, Y.F. Gu, Y. Yuan, T. Osada and H. Harada, Enhanced Mechanical Properties in a New Ni–Co Base Superalloy by Controlling Microstructures, Mater. Sci. Eng. A, 2011, 528(16–17), p 5465–5469. (in English)10.1016/j.msea.2011.03.085 ↗
16. M.S. Chen, Z.H. Zou, Y.C. Lin, H.B. Li and G.Q. Wang, Formation Mechanism of Large Grains Inside Annealed Microstructure of GH4169 Superalloy by Cellular Automation Method, J. Mater. Sci. Technol., 2019, 35(7), p 1403–1411. (in English)10.1016/j.jmst.2018.11.026 ↗
17. A. Ghasemi and M. Pouranvari, Thermal Processing Strategies Enabling Boride Dissolution and Gamma Prime Precipitation in Dissimilar Nickel-based Superalloys Transient Liquid Phase Bond, Mater. Design, 2019, 182, p 108008. (in English)10.1016/j.matdes.2019.108008 ↗
18. M. Pouranvari, A. Ekrami and A.H. Kokabi, Diffusion Brazing of Cast INCONEL 718 Superalloy Utilising Standard Heat Treatment Cycle, Mater. Sci. Tech-lond., 2014, 30(1), p 109–115. (in English)10.1179/1743284713Y.0000000320 ↗
19. E.J. Payton, T.A. Wynn and M.J. Mills, Experimental Measurement of the Kinetics of Gamma Prime Dissolution During Supersolvus Heat Treatment of Powder Metallurgical Ni-based Disk Superalloys, J. Mater. Sci., 2012, 47(20), p 7305–7311. (in English)10.1007/s10853-012-6684-8 ↗
20. F. Masoumi, M. Jahazi, D. Shahriari and J. Cormier, Coarsening and Dissolution of γ′ Precipitates During Solution Treatment of AD730™ Ni-based Superalloy: Mechanisms and Kinetics Models, J. Alloy. Compd., 2016, 658, p 981–995. (in English)10.1016/j.jallcom.2015.11.002 ↗
21. J. Cormier, X. Milhet and J. Mendez, Effect of Very High Temperature Short Exposures on the Dissolution of the γ′ Phase in Single Crystal MC2 Superalloy, J. Mater. Sci., 2007, 42(18), p 7780–7786. (in English)10.1007/s10853-007-1645-3 ↗
22. M. Jahazi and A.R. Mashreghi, Dissolution and Precipitation Kinetics of γ′ in Nickel Base Superalloy Udimet 520, Mater. Sci. Tech-lond., 2002, 18(4), p 458–462. (in English)10.1179/026708302225001606 ↗
23. I. Roy, E. Balikci, S. Ibekwe and A. Raman, Precipitate Growth Activation Energy Requirements in the Duplex Size γ′ Distribution in the Superalloy IN738LC, J. Mater. Sci., 2005, 40(23), p 6207–6215. (in English)10.1007/s10853-005-3154-6 ↗
24. F. Masoumi, M. Jahazi, J. Cormier, and D. Shahriari, Dissolution Kinetics and Morphological Changes of γ′ in AD730TM Superalloy, MATEC Web of Conferences, EDP Sciences, 2014, 13005, in English10.1051/matecconf/20141413005 ↗
25. A. Chamanfar, M. Jahazi, J. Gholipour, P. Wanjara and S. Yue, Evolution of Flow Stress and Microstructure During Isothermal Compression of Waspaloy, Mater. Sci. Eng. A, 2014, 615, p 497–510. (in English)10.1016/j.msea.2014.07.093 ↗
26. M. Oja, K.R. Chandran and R.G. Tryon, Orientation Imaging Microscopy of Fatigue Crack Formation in Waspaloy: Crystallographic Conditions for Crack Nucleation, Int. J. Fatigue, 2010, 32(3), p 551–556. (in English)10.1016/j.ijfatigue.2009.01.012 ↗
27. A. Chamanfar, M. Jahazi, J. Gholipour, P. Wanjara and S. Yue, Analysis of Integrity and Microstructure of Linear Friction Welded WASPALOY, Mater. Charact., 2015, 104, p 149–161. (in English)10.1016/j.matchar.2015.04.011 ↗
28. D. Kulawinski, S. Henkel, D. Holländer, M. Thiele, U. Gampe and H. Biermann, Fatigue Behavior of the Nickel-base Superalloy Waspaloy™ Under Proportional Biaxial-planar Loading at High Temperature, Int. J. Fatigue, 2014, 67, p 212–219. (in English)10.1016/j.ijfatigue.2014.02.005 ↗
29. H. Ding and Y.C. Shin, Improvement of Machinability of Waspaloy via Laser-Assisted Machining, Int. J. Adv. Manuf. Tech., 2013, 64(1), p 475–486. (in English)10.1007/s00170-012-4012-8 ↗
30. X. Wang, Y. Zhou, Z. Zhao and Z. Zhang, Effects of Solutioning on the Dissolution and Coarsening of γ′ Precipitates in a Nickel-based Superalloy, J. Mater. Eng. Perform., 2015, 24(4), p 1492–1504. (in English)10.1007/s11665-014-1368-y ↗
31. Z.H. Yao, M.C. Zhang and J.X. Dong, Stress Rupture Fracture Model and Microstructure Evolution for Waspaloy, Metall. Mater. Trans. A, 2013, 44(7), p 3084–3098. (in English)10.1007/s11661-013-1660-8 ↗
32. R. Giraud, Z. Hervier, J. Cormier, G. Saint-Martin, F. Hamon, X. Milhet and J. Mendez, Strain Effect on the γ′ Dissolution at high Temperatures of a Nickel-Based Single Crystal Superalloy, Metall. Mater. Trans. A, 2013, 44(1), p 131–146. (in English)10.1007/s11661-012-1397-9 ↗
33. T. Wang, X. Wang, Z. Zhao and Z. Zhang, Dissolution Behaviour of the γ′ Precipitates in Two Kinds of Ni-Based Superalloys, Mater. High Temp., 2016, 33(1), p 51–57. (in English)10.1179/1878641315Y.0000000006 ↗
34. Y. Guan, Y. Liu, Z. Ma, H. Li and H. Yu, Precipitation and Coarsening Behavior of γ′ Phase in CoNi-base Superalloy Under Different Aging Treatments, Vacuum, 2020, 175, p 109247. (in English)10.1016/j.vacuum.2020.109247 ↗
35. T. Wang, G. Sheng, Z.K. Liu and L.Q. Chen, Coarsening Kinetics of γ′ Precipitates in the Ni–Al–Mo System, Acta Mater., 2008, 56(19), p 5544–5551. (in English)10.1016/j.actamat.2008.07.024 ↗
36. J.Z. Zhu, T. Wang, A.J. Ardell, S.H. Zhou, Z.K. Liu and L.Q. Chen, Three-Dimensional Phase-Field Simulations of Coarsening Kinetics of γ′ Particles in Binary Ni–Al Alloys, Acta Mater., 2004, 52(9), p 2837–2845. (in English)10.1016/j.actamat.2004.02.032 ↗
37. Y.H. Wen, B. Wang, J.P. Simmons and Y. Wang, A Phase-field Model for Heat Treatment Applications in Ni-Based Alloys, Acta Mater., 2006, 54(8), p 2087–2099. (in English)10.1016/j.actamat.2006.01.001 ↗
38. X.D. Lu, J.H. Du and Q. Deng, High Temperature Structure Stability of GH4169 Superalloy, Mater. Sci. Eng. A, 2013, 559, p 623–628. (in English)10.1016/j.msea.2012.09.001 ↗
39. H. Monajati, M. Jahazi, R. Bahrami and S. Yue, The Influence of Heat Treatment Conditions on γ′ Characteristics in Udimet® 720, Mater. Sci. Eng. A, 2004, 373(1–2), p 286–293. (in English)10.1016/j.msea.2004.01.027 ↗
40. Y.Y. Zhao, H.W. Chen, Z.P. Lu and T.G. Nieh, Thermal Stability and Coarsening of Coherent Particles in a Precipitation-Hardened (NiCoFeCr)94Ti2Al4 High-Entropy Alloy, Acta Mater., 2018, 147, p 184–194. (in English)10.1016/j.actamat.2018.01.049 ↗
41. R.A. Swalin and A. Martin, Solute Diffusion in Nickel-base Substitutional Solid Solutions, J. Metals, 1956, 8, p 567–572. (in English)
42. J. Lan, H. Huang, H. Mao and L. Hua, Phase Transformation and Grain Growth Behaviors of Superalloy IN718 During Heat Treatment, Mater. Today Commun., 2020, 24, p 101347. (in English)10.1016/j.mtcomm.2020.101347 ↗
43. L.P. Freund, A. Stark, A. Kirchmayer, N. Schell, F. Pyczak, M. Göken and S. Neumeier, The Effect of a Grain Boundary Pinning B2 Phase on Polycrystalline Co-Based Superalloys with Reduced Density, Metall. Mater. Trans. A, 2018, 49(9), p 4070–4078. (in English)10.1007/s11661-018-4757-2 ↗
44. E.A. Holm, M.A. Miodownik and A.D. Rollett, On Abnormal Subgrain Growth and the Origin of Recrystallization Nuclei, Acta Mater., 2003, 51(9), p 2701–2716. (in English)10.1016/S1359-6454(03)00079-X ↗
45. J. Miao, T.M. Pollock and J.W. Jones, Crystallographic Fatigue Crack Initiation in Nickel-Based Superalloy René 88DT at Elevated Temperature, Acta Mater., 2009, 57(20), p 5964–5974. (in English)10.1016/j.actamat.2009.08.022 ↗