On the Interaction to Thermal Cycle Curve and Numerous Theories of Failure Criteria for Weld-Induced Residual Stresses in AISI304 Steel using Element Birth and Death Technique
Source abstract
Abstract
In this present study, element birth and death technique is used in simulation to compute thermal history as in transient temperature distribution and thermal cycle curve to find cooling rates in the heat-affected zones and residual stresses in 8-mm-thick AISI304 steel weldment. The peak values of residual stresses in the weldment were observed as high as (269 and 289 MPa in SQBWJ and 258 and 260 MPa in VGBWJ) which is significantly higher than the yield stress (σy) value of AISI304 at room temperature due to higher rate of strain hardening and larger coefficient of thermal expansion. The predicted results of each criterion of residual stresses lead to finding the location for cause of premature failure of AISI304 weldment. All the aspects of failure investigation are important in answering the questions raised for the failure and to avoid any future miss-happening. Graphical Abstract
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. K. Chandra, V. Kain, and P. Ganesh, Controlling End-Grain Corrosion of Austenitic Stainless Steels, J. Mater. Eng. Perform., 2008, 17, p 115–122.10.1007/s11665-007-9117-0 ↗
2. J.A. Siefert and S.A. David, Weldability and Weld Performance of Candidate Austenitic Alloys for Advanced Ultrasupercritical Fossil Power Plants, Sci. Technol. Weld. Join., 2014, 19, p 271–294. https://doi.org/10.1179/1362171814Y.000000019710.1179/1362171814Y.0000000197 ↗
3. L. Falat, L. Čiripová, J. Kepič, J. Buršík, and I. Podstranská, Correlation Between Microstructure and Creep Performance of Martensitic/Austenitic Transition Weldment in Dependence of its Post-Weld Heat Treatment, Eng. Fail. Anal., 2014, 40, p 141–152. https://doi.org/10.1016/j.engfailanal.2014.02.01810.1016/j.engfailanal.2014.02.018 ↗
4. L. Boriwal, R.M. Sarviya, and M.M. Mahapatra, Optimization of Weld Bonding Process Parameters of Austenitic Stainless Steel 304L and Low Carbon Steel Sheet Dissimilar Joints, J. Adhes. Sci. Technol., 2017, 31, p 1591–1616. https://doi.org/10.1080/01694243.2016.126684410.1080/01694243.2016.1266844 ↗
5. M. Shakil, M. Ahmad, N.H. Tariq, B.A. Hasan, J.I. Akhter, E. Ahmed et al., Microstructure and Hardness Studies of Electron Beam Welded Inconel 625 and Stainless Steel 304L, Vacuum, 2014, 110, p 121–126. https://doi.org/10.1016/j.vacuum.2014.08.01610.1016/j.vacuum.2014.08.016 ↗
6. Y. Ye, J. Cai, X. Jiang, D. Dai, and D. Deng, Influence of Groove Type on Welding-Induced Residual Stress, Deformation and width of Sensitization Region in a SUS304 Steel Butt Welded Joint, Adv. Eng. Softw., 2015, 86, p 39–48.10.1016/j.advengsoft.2015.04.001 ↗
7. L.N. Robert, Machine Design an Integrated Approach, Pearson Prentice Hall Publishers, USA, 2006.
8. G. Totten, Handbook on Residual Stress, Vol 1 SEM, Bethel, 2005, p 417. (ISBN:978-0871707291)
9. E. Macherauch and K.H. Kloos, Origin, Measurements and Evaluation of Residual Stresses, Residual Stress Sci. Technol., 1987, 1, p 3–26.
10. D. Deng and S. Kiyoshima, Numerial Simulation of Residual Stresses Induced by Laser Beam Welding in a SUS316 Stainless Steel Pipe with Considering Initial Residual Stress Influences, Nucl. Eng. Des., 2010, 240(4), p 688–696.10.1016/j.nucengdes.2009.11.049 ↗
11. P.K. Taraphdar, J.G. Thakare, C. Pandey, and M.M. Mahapatra, Novel Residual Stress Measurement Technique to Evaluate Through Thickness Residual Stress Fields, Mater. Lett., 2020, 15(277), p 128347.10.1016/j.matlet.2020.128347 ↗
12. P.K. Taraphdar, R. Kumar, C. Pandey, and M.M. Mahapatra, Significance of Finite Element Models and Solid-State Phase Transformation on the Evaluation of Weld Induced Residual Stresses, Met. Mater. Int., 2021, 27(9), p 3478–3492.10.1007/s12540-020-00921-4 ↗
13. J. Jang, D. Son, and Y.H. Lee, Assessing Welding Residual Stress in A335 P12 Steel Welds Before and After Stress-Relaxation Annealing Through Instrumented Indentation Technique, Scripta Mater, 2003, 48, p 743–748.10.1016/S1359-6462(02)00537-7 ↗
14. D. Ulutan, E.B. Alaca, and I.J. Lazoglu, Analytical Modelling of Residual Stresses in Machining, J. Mater. Process. Technol., 2007, 183, p 77–87.10.1016/j.jmatprotec.2006.09.032 ↗
15. V. Dattoma, M.D. Giorgi, and R. Nobile, On the Evolution of Welding Residual Stress after Milling and Cutting Machining, Comput. Struct., 2006, 84, p 1965–1976.10.1016/j.compstruc.2006.08.008 ↗
16. Y. Ueda and T. Yamakawa, Analysis of Thermal Elastic-Plastic Stress and Strain During Welding by Finite Element Method, Trans. JWS, 1971, 2(2), p 90–100.
17. G. Fu, I.L. Marcelo, M. Duan, and F.E. Segen, Effect of Boundary Conditions on Residual Stress and Distortion in T-joint Welds, J. Constr. Steel Res., 2014, 102, p 121–135.10.1016/j.jcsr.2014.07.008 ↗
18. J. Ju, F. Xue, J. Zhou, J. Bai, and L. Sun, Interface and Bond Strength of Brazing Cemented Carbide K20 to Alloy Steel AISI 4140 by High-Frequency Induction, Mater. Manuf. Process., 2016, 31(8), p 1052–1060.10.1080/10426914.2015.1048357 ↗
19. Y. Rong, G. Zhang, and Y. Huang, Study of Welding Distortion and Residual Stress Considering Nonlinear Yield Stress Curves and Multi-Constraint Equations, J. Mater. Eng. Perform., 2016, 25(10), p 4484–4494.10.1007/s11665-016-2259-1 ↗
20. M.H. Nozari, S. Ziaee, and K. Jafarpur, Experimental Study of Produced Thermal Stresses in thin Arc Welded Plates: Application of Constructal Theory in Welding Paths, Weld. World, 2016, 60(1), p 51–59.10.1007/s40194-015-0277-5 ↗
21. J. Goldak and M. Akhlaghi, Computational Welding Mechanics, Springer-Verlag, New York Inc., USA, 2005. (ISBN: 9780387232874)
22. L.E. Lindgren, Computational Welding Mechanics, Woodhead Publishing, UK, 2007. (ISBN: 1845692217)10.1201/9781439824092 ↗
23. Guide for Verification and Validation in Computation Weld Mechanics, American Welding Society, USA, 2013.
24. Y. Luo, W. Jiang, W. Zhang, Z. Wei, Q. Zhang, Y. Wan, and Y.J. Wang, Experimental and Numerical Study on the Reduction of Residual Stress in the Fillet Weld by Overlay Welding and Cutting Method, J. Press. Vessel. Technol., 2016, 138(6), p 060401–060407.10.1115/1.4033529 ↗
25. D. Venkatkumar and D. Ravindran, 3D Finite Element Simulation of Temperature Distribution, Residual Stress and Distortion on 304 Stainless Steel Plates using GTA Welding, J. Mech. Sci. Technol., 2016, 30(1), p 67–76.10.1007/s12206-015-1208-5 ↗
26. K. Seleš, M. Perić, and Z. Tonković, Numerical Simulation of a Welding Process Using a Prescribed Temperature Approach, J. Constr. Steel Res., 2018, 1(145), p 49–57.10.1016/j.jcsr.2018.02.012 ↗
27. D. Deng, H. Murakawa, and W. Liang, Numerical Simulation of Welding Distortion in Large Structures, Comput. Methods Appl. Mech. Eng., 2007, 196(45–48), p 4613–4627.10.1016/j.cma.2007.05.023 ↗
28. T.S. Jun and A.M. Korsunsky, Evaluation of Residual Stresses and Strains using the Eigenstrain Reconstruction Method, Int. J. Solids Struct., 2010, 47(13), p 1678–1686.10.1016/j.ijsolstr.2010.03.002 ↗
29. M. Perić, Z. Tonković, A. Rodić, M. Surjak, I. Garašić, I. Boras, and S. Švaić, Numerical Analysis and Experimental Investigation in a T-joint Fillet Weld, Mater. Des., 2014, 53, p 1052–1063.10.1016/j.matdes.2013.08.011 ↗
30. M. Shubert and M. Pandheeradi, An Abaqus Extension for 3-D Welding Simulations, Mater. Sci. Forum, 2014, 768, p 768–769.
31. P. Meena, M. Kumar, M. Singh, D. Kumar Shukla, R.G. Burela, P. Jhunjhunwala, A. Gupta, and C. Pandey, Numerical Analysis of Different SUS304 Steel Weld Joint Configurations using New Prescribed Temperature Approach, Trans. Indian Inst. Met., 2022, 75(6), p 1649–1668.10.1007/s12666-021-02389-1 ↗
32. ASM International, Welding Brazing and Soldering, Asm Int., 2019, 6(6), p 362–372.
33. H. Eisazadeh, A. Achuthan, J.A. Goldak, and D.K. Aidun, Effect of Material Properties and Mechanical Tensioning Load on Residual Stress Formation in GTA 304–A36 Dissimilar Weld, J. Mater. Process. Technol., 2015, 1(222), p 344–355.10.1016/j.jmatprotec.2015.03.021 ↗
34. P.H. Chang and T.L. Teng, Numerical and Experimental Investigations on the Residual Stresses of the Butt-Welded Joints, Comput. Mater. Sci., 2004, 29(4), p 511–522.10.1016/j.commatsci.2003.12.005 ↗
35. D. Deng and H. Murakawa, Numerical Simulation of Temperature Field and Residual Stress in Multi-Pass Welds in Stainless Steel Pipe and Comparison with Experimental Measurements, Comput. Mater. Sci., 2006, 37(3), p 269–277.10.1016/j.commatsci.2005.07.007 ↗
36. A.S. Elmesalamy, H. Abdolvand, J.N. Walsh, J.A. Francis, W. Suder, S. Williams, and L. Li, Measurement and Modelling of the Residual Stresses in Autogenous and Narrow Gap Laser Welded AISI Grade 316L Stainless Steel Plates, Int. J. Press. Vessel. Pip., 2016, 147, p 64–78.10.1016/j.ijpvp.2016.09.007 ↗
37. D. Rosenthal, The Theory of Moving Sources of Heat and its Application to Metal Treatments, Trans. ASME, 1946, 68, p 849–865.
38. R.R. Rykalin, Energy Sources for Welding, Weld. World, 1974, 12(9/10), p 227–248.
39. M. Perić, S. Nižetić, I. Garašić, N. Gubeljak, T. Vuherer, and Z. Tonković, Numerical Calculation and Experimental Measurement of Temperatures and Welding Residual Stresses in a Thick-Walled T-joint Structure, J. Therm. Anal. Calorim., 2020, 141(1), p 313–322.10.1007/s10973-019-09231-3 ↗
40. D. Deng, Y. Luo, H. Serizawa, M. Shibahara, and H. Murakawa, Numerical Simulation of Residual Stress and Deformation Considering Phase Transformation Effects (Mechanics, Strength & Structural Design), Trans. JWRI, 2003, 32(2), p 325–333.