Effect of Strain Rate on the Plastic Deformation and Fracture of 90W-7Ni-3Fe Alloy Prepared by Liquid-Phase Sintering
Source abstract
Abstract
In this study, the effect of the strain rates on the plastic deformation behavior and fracture mechanism of 90W-7Ni-3Fe heavy alloy prepared by liquid-phase sintering was investigated. Stress–strain tests were carried out in tensile and compression under quasi-static condition with the strain rate ranging from 10−3 to 1 s−1. Dynamic test was examined using a compression split Hopkinson bar at strain rates ranging from 1000 to 1700 s−1 in order to evaluate the effects of high strain rate on dynamic plastic deformation behavior. Quasi-static tests results show that the strength and hardness of this alloy increase with increasing strain rate. Results indicate that the as-sintered 90W-7Ni-3Fe heavy alloy has obvious strain-hardening characteristic under tensile or compression deformation under quasi-static condition. At this time, strain hardening is the main factor. Nevertheless, strain-hardening and strain-softening behaviors of the specimens occur simultaneously under dynamic compression condition. The effect of compressive stress on the work hardening is more obvious. A strong relevance of work-hardening effect on strain rate is also found. And the fracture mode of quasi-static and dynamic compression samples is also different.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Nuclear Materials and Properties · Orthopaedic implants and arthroplasty
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. A. Upadhyaya, Processing Strategy for Consolidating Tungsten Heavy Alloys for Ordnance Applications, Mater. Chem. Phys., 2001, 67, p 101–11010.1016/S0254-0584(00)00426-0 ↗
2. C.R. Kerley, C.E. Easterly, K.F. Eckerman, Environmental acceptability of high-performance alternatives for depleted uranium penetrators, in Office of Scientific and Technical Information Technical Reports (1996)10.2172/464128 ↗
3. W. Burkart, P.R. Danesi, and J.H. Hendry, Properties, Use and Health Effects of Depleted Uranium, Int. Congr., 2005, 1276(1276), p 133–13610.1016/j.ics.2004.09.047 ↗
4. R.M. German, Sintering Theory and Practice, Wiley, New York, 1996
5. J. Das, G.A. Rao, and S.K. Pabi, Microstructure and Mechanical Properties of Tungsten Heavy Alloys, Mater. Sci. Eng., A, 2010, 527, p 7841–784710.1016/j.msea.2010.08.071 ↗
6. A. Mondal, A. Upadhyaya, and D. Agrawal, Effect of Heating Mode and Sintering Temperature on the Consolidation of 90 W-7Ni-3Fe Alloys, J. Alloys Compd., 2011, 509, p 301–31010.1016/j.jallcom.2010.09.008 ↗
7. W.S. Lee, C.F. Lin, and S.T. Chang, Plastic Flow of Tungsten-Based Composite Under Hot Compression, J. Mater. Process. Technol., 2000, 100(1-3), p 123–13010.1016/S0924-0136(99)00466-5 ↗
8. H. Hafızoğlu and N. Durlua, Effect of Sintering Temperature on the High Strain Rate-Deformation of Tungsten Heavy Alloys, Int. J. Impact Eng, 2018, 121, p 44–54. https://doi.org/10.1016/j.ijimpeng.2018.07.00110.1016/j.ijimpeng.2018.07.001 ↗
9. S. Yadav and K.T. Ramesh, The Mechanical Properties of Tungsten-Based Composites at Very High Strain Rates, Mater. Sci. Eng., A, 1995, 203, p 140–15310.1016/0921-5093(95)09865-8 ↗
10. Y.X. Zhou, Y. Wang, P.K. Mallick et al., Strain Softening Constitutive Equation for Tungsten Heavy Alloy Under Tensile Impact, Mater. Lett., 2004, 58, p 2725–272910.1016/j.matlet.2004.03.048 ↗
11. W.S. Lee, G.L. Xiea, and C.F. Lin, The Strain Rate and Temperature Dependence of the Dynamic Impact Response of Tungsten Composite, Mater. Sci. Eng., A, 1998, 257, p 256–26710.1016/S0921-5093(98)00852-1 ↗
12. D. Rittel, R. Levin, and A. Dorgoy, On the Isotropy of the Dynamic Mechanical and Failure Properties of Swaged Tungsten Heavy Alloys, Metall. Mater. Trans. A, 2004, 35, p 3787–379510.1007/s11661-004-0284-4 ↗
13. X. Gong, J.L. Fan, B.Y. Huang et al., Microstructure Characteristics and a Deformation Mechanism of Fine-Grained Tungsten Heavy Alloy Under High Strain Rate Compression, Mater. Sci. Eng., A, 2010, 527, p 7565–757010.1016/j.msea.2010.07.102 ↗
14. Y.Z. Ma, J.J. Zhang, W.S. Liu et al., Microstructure and Dynamic Mechanical Properties of Tungsten-Based Alloys in the Form of Extruded Rods Via Microwave Heating, Int. J. Refract. Met. Hard Mater., 2014, 42, p 71–7610.1016/j.ijrmhm.2013.08.003 ↗
15. D.S. Kim, S. Nemat-Nasser, J.B. Isaacs et al., Adiabatic Shearband in WHA in High-Strain-Rate Compression, Mech. Mater., 1998, 28, p 227–23610.1016/S0167-6636(97)00068-9 ↗
16. A.K. Zurek and P.S. Follansbee, A Comparison of Shear Localization Susceptibility in U-0.75 wt pct Ti and W-Ni-Fe During High Strain Rate Deformation, Metall. Mater. Trans. A, 1995, 26, p 1483–149010.1007/BF02647599 ↗
17. J.L. Fan, X. Gong, B.Y. Huang et al., Dynamic Failure and Adiabatic Shear Bands in Fine-Grain 93 W-4.9Ni-2.1Fe Alloy with Y2O3 Addition Under Lower High-Strain-Rate (HSR) Compression, Mech. Mater., 2010, 42, p 24–3010.1016/j.mechmat.2009.08.006 ↗
18. K. Hu, X.Q. Li, M. Guan et al., Dynamic Deformation Behavior of 93 W-5.6Ni-1.4Fe Heavy Alloy Prepared by Spark Plasma Sintering, Int. J. Refract. Met. Hard Mater., 2016, 58, p 117–12410.1016/j.ijrmhm.2016.04.010 ↗
19. J. Das, G.A. Rao, S.K. Pabi et al., Deformation Behaviour of a Newer Tungsten Heavy Alloy, Mater. Sci. Eng., A, 2011, 528, p 6235–624710.1016/j.msea.2011.04.067 ↗
20. Y. Yu, C.Y. Ren, and W.C. Zhang, Compressive Behavior of Liquid Phase Sintered 90 W-7Ni-3Fe Heavy Alloy at High Temperature and Low Strain rate Condition, Int. J. Refract. Met. Hard Mater., 2018, 76, p 149–15710.1016/j.ijrmhm.2018.06.006 ↗
21. M. Scapin, Mechanical Characterization and Modeling of the Heavy Tungsten Alloy IT180, Int. J. Refract. Met. Hard Mater., 2015, 50, p 258–26810.1016/j.ijrmhm.2015.01.018 ↗
22. Z.J. Xu and F.L. Huang, Thermomechanical Behavior and Constitutive Modeling of Tungsten-Based Composite Over Wide Temperature and Strain Rate Ranges, Int. J. Plast, 2013, 40, p 163–18410.1016/j.ijplas.2012.08.004 ↗