Effect of Shot Peening on Residual Stress Distribution and Microstructure Evolution of Artificially Defected 50CrV4 Steel
Source abstract
Abstract
The aim of this paper is to clarify the effects of shot peening on fatigue life and strain hardening behavior of spring steel samples containing artificial surface defect. Artificial defect acting as pre-cracks is introduced and the effects of this defect on the material surface and the distribution of residual stress away from the defect are investigated before and after shot peening. Shot peening has provided the following modifications on the surface: (1) homogenous compressive residual stress, (2) high dislocation density, (3) superficial strain hardening, (4) retained austenite reduction. In this paper, shot peening is applied to 50CrV4 steel and its effect on surface roughness, microhardness, surface residual stress, crystallite size and dislocation density calculation is determined and SEM observations are used to reveal the properties severely strain-hardened layer. It can be shown that the shot peening can modify the crystallite size, however, the main effect is achieved by increasing the dislocation density and inducing the highly compressive residual stress. The effect of the surface modification to the 3-point bending fatigue life are analyzed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · High-Velocity Impact and Material Behavior · Erosion and Abrasive Machining
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. K. Dalaei and B. Karlsson, Influence of Shot Peening on Fatigue Durability of Normalized Steel Subjected to Variable Amplitude Loading, Int. J. Fatigue, 2012, 38, p 7583. https://doi.org/10.1016/J.İjfatigue.2011.11.01110.1016/J.İjfatigue.2011.11.011 ↗
2. S. Bajda, W. Ratuszek, M. Krzyzanowski, and D. Retraint, Inhomogeneity of Plastic Deformation in Austenitic Stainless Steel After Surface Mechanical Attrition Treatment, Surf. Coat. Technol., 2017, 329, p 202–211. https://doi.org/10.1016/J.Surfcoat.2017.09.04910.1016/J.Surfcoat.2017.09.049 ↗
3. S. Shen and S.N. Atluri, An Analytical Model fors Hot-Peening Imduced Residual Stresses, Comput. Mater. Contin., 2006, 4, p 75–85. https://doi.org/10.3970/Cmc.2006.004.07510.3970/Cmc.2006.004.075 ↗
4. K. Zhan, C.H. Jiang, and V. Ji, Uniformity of Residual Stress Distribution on the Surface of S30432 Austenitic Stainless Steel by Different Shot Peening Processes, Mater. Lett., 2013, 99, p 61–64. https://doi.org/10.1016/J.Matlet.2012.08.14710.1016/J.Matlet.2012.08.147 ↗
5. E. Delosrıos, A. Walley, M. Mılan, and G. Hammersley, Fatigue Crack Initiation and Propagation on Shot-Peened Surfaces in A316 Stainless Steel, Int. J. Fatıgue, 1995, 17(7), p 493–499. https://doi.org/10.1016/0142-1123(95)00044-T10.1016/0142-1123(95)00044-T ↗
6. A.L.M. Carvalho and H.J.C. Voorwald, Influence of Shot Peening and Hard Chromium Electroplating on the Fatigue Strength of 7050-T7451 Aluminum Alloy, Int. J. Fatigue, 2007, 29(7), p 1282–1291. https://doi.org/10.1016/J.İjfatigue.2006.10.00310.1016/J.İjfatigue.2006.10.003 ↗
7. V.M. Radhakrishnan and P.S. Baburamani, Initiation and Propagation of Fatigue Crack in Pre-strained Material, Int. J. Fract., 1976, 12(3), p 369–380. https://doi.org/10.1007/Bf0003283210.1007/Bf00032832 ↗
8. K.A. Soady, Life Assessment Methodologies Incoroporating Shot Peening Process Effects: Mechanistic Consideration of Residual Stresses and Strain Hardening Part 1—Effect of Shot Peening on Fatigue Resistance, Mater. Sci. Technol. Ser., 2013, 29(6), p 637–651. https://doi.org/10.1179/1743284713y.000000022210.1179/1743284713y.0000000222 ↗
9. L. Trško, M. Guagliano, P. Lukáč, O. Bokůvka, and F. Nový, Effects of Severe Shot Peening on the Surface State of Aw 7075 Al Alloy, Kovove Mater., 2015, 53(4), p 239–243. https://doi.org/10.4149/Km-2015-4-23910.4149/Km-2015-4-239 ↗
10. P. Zhang, J. Lindemann, and C. Leyens, Influence of Shot Peening on Notched Fatigue Strength of the High-Strength Wrought Magnesium Alloy Az80, J. Alloys Compd., 2010, 479(1–2), p 380–385. https://doi.org/10.1016/J.Jallcom.2010.03.07910.1016/J.Jallcom.2010.03.079 ↗
11. J.W. Tian, J.C. Villegas, W. Yuan, D. Fielden, L. Shaw, P.K. Liaw, and D.L. Klarstrom, A Study of the Effect of Nanostructured Surface Layers on the Fatigue Behaviors of A C-2000 Superalloy, Mater. Sci. Eng. A Struct., 2007, 468–470, p 167–170. https://doi.org/10.1016/J.Msea.2006.10.15010.1016/J.Msea.2006.10.150 ↗
12. J. Zhang, S. Lı, Z. Yang, G. Lı, W. Huı, and Y. Weng, Influence of Inclusion Size on Fatigue Behavior of High Strength Steels in the Gigacycle Fatigue Regime, Int. J. Fatıgue, 2007, 29(4), p 765–771. https://doi.org/10.1016/J.İjfatigue.2006.06.00410.1016/J.İjfatigue.2006.06.004 ↗
13. Q.Y. Wang, J.Y. Berard, S. Rathery, and C. Bathias, Technical Note High-Cycle Fatigue Crack Initiation and Propagation Behaviour of High-Strength Sprin Steel Wires, Fatigue Fract. Eng. Mater., 1999, 22(8), p 673–677. https://doi.org/10.1046/J.1460-2695.1999.T01-1-00184.X10.1046/J.1460-2695.1999.T01-1-00184.X ↗
14. I. Fernández-Pariente, S. Bagherifard, M. Guagliano, and R. Ghelichi, Fatigue Behavior of Nitrided and Shot Peened Steel with Artificial Small Surface Defects, Eng. Fract. Mech., 2013, 103, p 2–9. https://doi.org/10.1016/J.Engfracmech.2012.09.01410.1016/J.Engfracmech.2012.09.014 ↗
15. S. Bagherifard, I. Fernandez-Pariente, R. Ghelichi, and M. Guagliano, Fatigue Behavior of Notched Steel Specimens with Nanocrystallized Surface Obtained by Severe Shot Peening, Mater. Des., 2013, 45, p 497–503. https://doi.org/10.1016/J.Matdes.2012.09.02510.1016/J.Matdes.2012.09.025 ↗
16. Z.Y. Wang, Q.Y. Wang, L. Li, and N. Zhang, Fatigue Behaviour of CFRP Strengthened Open-Hole Steel Plates, Thin Wall Struct., 2017, 115, p 176–187. https://doi.org/10.1016/J.Tws.2017.02.01510.1016/J.Tws.2017.02.015 ↗
17. M. Benedetti, V. Fontanari, B. Winiarski, M. Allahkarami, and J.C. Hanan, Residual Stresses Reconstruction in Shot Peened Specimens Containing Sharp and Blunt Notches by Experimental Measurements and Finite Element Analysis, Int. J. Fatigue, 2016, 87, p 102–111. https://doi.org/10.1016/J.İjfatigue.2016.01.02010.1016/J.İjfatigue.2016.01.020 ↗
18. C.A. Vázquez Jiménez, G. Gómez Rosas, C. Rubio González, V. Granados Alejo, and S. Hereñú, Effect of Laser Shock Processing on Fatigue Life of 2205 Duplex Stainless Steel Notched Specimens, Opt. Laser Technol., 2017, 97, p 308–315. https://doi.org/10.1016/J.Optlastec.2017.07.02010.1016/J.Optlastec.2017.07.020 ↗
19. Z. Wang, C. Jiang, X. Gan, and Y. Chen, Effect of shot peening on the microstructure of laser hardened 17-4ph, Appl. Surf. Sci., 2010, 257(4), p 1154–1160. https://doi.org/10.1016/J.Apsusc.2010.07.01510.1016/J.Apsusc.2010.07.015 ↗
20. Y. Yamada and T. Kuwabara, Materials For Springs, Springer, Berlin, 2007
21. Y. Lv, L. Lei, and L. Sun, Effect of Shot Peening on the Fatigue Resistance of Laser Surface Melted 20CrMnTi Steel Gear, Mater. Sci. Eng. A Struct., 2015, 629, p 8–15. https://doi.org/10.1016/J.Msea.2015.01.07410.1016/J.Msea.2015.01.074 ↗
22. Z.Y. Wang, Q.Y. Wang, and M. Cao, Experimental Study on Fatigue Behaviour of Shot-Peened Open-Hole Steel Plates, Materials, 2017, 10(9), p p99610.3390/ma10090996 ↗
23. S.G. Irizalp, N. Saklakoglu, and B.S. Yilbas, Characterization of Microplastic Deformation Produced in 6061-T6 by Using Laser Shock Processing, Int. J. Adv. Manuf. Technol., 2014, 71(1–4), p 109–11510.1007/s00170-013-5481-0 ↗
24. O. Anderoglu, Residual Stress Measurement Using X-Ray Diffraction. Doctoral Dissertation, Texas A&M University, 2005
25. A. Küçükyılmaz, Experimental Investigation of Residual Stresses Introduced Via Shot Peening and Their Effect on Fatigue Life of Ball Bearings (Master’s Thesis), Middle East Technical University, 2010
26. A. Kubit, M. Bucior, W. Zielecki, and F. Stachowicz, The Impact of Heat Treatment and Shot Peening on the Fatigue Strength of 51CrV4 Steel, Procedia Struct. Integr., 2016, 2, p 3330–333610.1016/j.prostr.2016.06.415 ↗
27. A. Aviles, R. Aviles, J. Albizuri, L. Pallares-Santasmartas, and A. Rodriguez, Effect of Shot-Peening and Low-Plasticity Burnishing on the High-Cycle Fatigue Strength of DIN 34CrNiMo6 Alloy Steel, Int. J. Fatigue, 2019, 119, p 338–35410.1016/j.ijfatigue.2018.10.014 ↗
28. X. Li, J. Zhang, B. Yang, J. Zhang, M. Wu, and L. Lu, Effect of Micro-shot Peening, Conventional Shot Peening and Their Combination on Fatigue Property of EA4T Axle Steel, J. Mater. Process. Technol., 2020, 275, p p11632010.1016/j.jmatprotec.2019.116320 ↗
29. F. Klocke, J. Gomes, C. Löpenhaus, and R.R. Rego, Assessing the Heterogeneity of Residual Stress for Complementing the Fatigue Performance Comprehension, J. Strain Anal. Eng. Des., 2016, 51(5), p 347–35710.1177/0309324716636979 ↗
30. B. Fultz and J. Howe, Diffraction Line Shapes. Transmission Electron Microscopy and Diffractometry of Materials, 4th ed., Springer, Berlin, 2013, p 429–46210.1007/978-3-642-29761-8 ↗
31. J. Gubicza, N.Q. Chinh, J.L. Lábár, Z. Hegedűs, P. Szommer, G. Tichy, and T.G. Langdon, Delayed Microstructural Recovery in Silver Processed by Equal-Channel Angular Pressing, J. Mater. Sci., 2008, 43(16), p 5672–5676. https://doi.org/10.1007/S10853-008-2817-510.1007/S10853-008-2817-5 ↗
32. B.N. Mordyuk, Y.V. Milman, M.O. Iefimov, G.I. Prokopenko, V.V. Silberschmidt, M.I. Danylenko, and A.V. Kotko, Characterization of Ultrasonically Peened and Laser-Shock Peened Surface Layers of AISI, 321 Stainless Steel, Surf. Coat. Technol., 2008, 202, p 4875–488310.1016/j.surfcoat.2008.04.080 ↗
33. V. Ji, Y.G. Zhang, and C.Q. Chen, Characterization of Ultrasonically Peened and Laser-Shock Peened Surface Layers of AISI, 321 Stainless Steel, Surf. Coat. Technol., 2000, 130(1), p 95–9910.1016/S0257-8972(00)00683-6 ↗
34. N. Saklakoglu, S. Gencalp Irizalp, E. Akman, and A. Demir, Near Surface Modification of Aluminum Alloy Induced by Laser Shock Processing, Opt. Laser Technol., 2014, 64, p 235–24110.1016/j.optlastec.2014.05.028 ↗
35. S. Gencalp Irizalp and N. Saklakoglu, Laser Peening of Metallic Materials. Comprehensive Materials Finishing, Elsevier, Amsterdam, 2016, p 408
36. K. Li, X.S. Fu, R.D. Li, W.L. Zhou, and Z.Q. Li, A Mechanism Study on Characteristic Curve of Residual Stress FIELD in Ti–6Al–4V Induced by Wet Peening Treatment, Mater. Des., 2015, 86, p 761–76410.1016/j.matdes.2015.07.117 ↗
37. A. Zhao, J. Xie, C. Sun, Z. Lei, and Y. Hong, Effects of Strength Level and Loading Frequency on Very-High-Cycle Fatigue Behavior for a Bearing Steel, Int. J. Fatigue, 2012, 38, p 46–5610.1016/j.ijfatigue.2011.11.014 ↗
38. K. Miková, S. Bagherifard, O. Bokuvka, M. Guagliano, and L. Trško, Fatigue Behavior of X70 Microalloyed Steel After Severe Shot Peening, Int. J. Fatıgue, 2013, 55, p 33–42. https://doi.org/10.1016/J.İjfatigue.2013.04.02110.1016/J.İjfatigue.2013.04.021 ↗
39. S.G. Irizalp, N. Saklakoglu, E. Akman, and A. Demir, Pulsed Nd: Yag Laser Shock Processing Effects on Mechanical Properties of 6061-T6 alloy, Opt. Laser Technol., 2014, 56, p 273–27710.1016/j.optlastec.2013.08.011 ↗
40. N.A. Smyth, M.B. Toparli, M.E. Fitzpatrick, and P.E. Irving, Recovery of Fatigue Life Using Laser Peening on 2024-t351 Aluminium SHEET Containing Scratch Damage: The Role of Residual Stress, Fatigue Fract. Eng. Mater., 2019, https://doi.org/10.1111/Ffe.1298110.1111/Ffe.12981 ↗
41. V. Singh, V. Pandey, S. Kumar, N.C.S. Srinivas, and K. Chattopadhyay, Effect of Ultrasonic Shot Peening on Surface Microstructure and Fatigue Behavior of Structural Alloys, Trans. Indian Inst. Met., 2015, 69(2), p 295–301. https://doi.org/10.1007/S12666-015-0771-X10.1007/S12666-015-0771-X ↗
42. K. Dalaei and B. Karlsson, Influence of Overloading on Fatigue Durability and Stability of Residual Stresses in Shot Peened Normalized Steel, Mater. Sci. Eng. A Struct., 2011, 528(4), p 7323–7330. https://doi.org/10.1016/J.Msea.2011.06.00210.1016/J.Msea.2011.06.002 ↗
43. P.J. Withers, Residual Stress and Its Role in Failure, Rep. Progress Phys., 2007, 70(12), p 221110.1088/0034-4885/70/12/R04 ↗
44. A. Zammit, M. Mhaede, M. Grech, S. Abela, and L. Wagner, Influence of Shot Peening on the Fatigue Life of Cu–Ni Austempered Ductile Iron, Mater. Sci. Eng. A Struct., 2012, 545, p 78–85. https://doi.org/10.1016/J.Msea.2012.02.09210.1016/J.Msea.2012.02.092 ↗
45. F. Takahashi, A. Tange, and K. Ando, Effect of Shot Peening on Fatigue Limit of Surface Flawed Samples, Fatigue Fract. Eng. Mater., 2008, 31(3–4), p 242–250. https://doi.org/10.1111/J.1460-2695.2008.01219.X10.1111/J.1460-2695.2008.01219.X ↗
46. J. Sakamoto, Y.S. Lee, and S.K. Cheong, Effect of Surface Flaw on Fatigue Strength of Shot-Peened Medium-Carbon Steel, Eng. Fract. Mech., 2015, 133, p 99–111. https://doi.org/10.1016/J.Engfracmech.2014.11.00510.1016/J.Engfracmech.2014.11.005 ↗
47. M. Torres and H.J.C. Voorwald, An Evaluation of Shot Peening, Residual Stress and Stress Relaxation on the Fatigue Life of Aısı 4340 Steel, Int. J. Fatigue, 2002, 24(8), p 877–886. https://doi.org/10.1016/S0142-1123(01)00205-510.1016/S0142-1123(01)00205-5 ↗
48. S.A. Meguid, G. Shagal, J.C. Stranart, K.M. Liew, and L.S. Ong, Relaxation of Peening Residual Stresses Due to Cyclic Thermo-Mechanical Overload, J. Eng. Mater. Technol., 2005, 127(2), p 170–178. https://doi.org/10.1115/1.186798610.1115/1.1867986 ↗
49. A. Bag, D. Delbergue, J. Ajaja, P. Bocher, M. Lévesque, and M. Brochu, Effect of Different Shot Peening Conditions on the Fatigue LIFE of 300 m Steel Submitted to High Stress Amplitudes, Int. J. Fatigue, 2020, 130, p 105274. https://doi.org/10.1016/J.İjfatigue.2019.10527410.1016/J.İjfatigue.2019.105274 ↗
50. D. Löhe and O. Vöhringer, Stability of Residual Stresses. Handbook of Residual Stress and Deformation of Steel, ASM, Materials Park, 2003, p 54–69
51. K. Dalaei, B. Karlsson, and L.E. Svensson, Stability of Shot Peening Induced Residual Stresses and Their Influence on Fatigue Lifetime, Mater. Sci. Eng. A Struct., 2011, 528(3), p 1008–1015. https://doi.org/10.1016/J.Msea.2010.09.05010.1016/J.Msea.2010.09.050 ↗