Correlation Between Shear Punch and Tensile Strength for Low-Carbon Steel and Stainless Steel Sheets
Source abstract
Abstract
The deformation behavior of AISI 1015 low-carbon steel, and AISI 304 stainless steel sheets was investigated by uniaxial tension and the shear punch test (SPT). Both materials were cold rolled to an 80% thickness reduction and subsequently annealed in the temperature range 25-850 °C to produce a wide range of yield and ultimate strength levels. The correlations between shear punch and tensile yield and ultimate stresses were established empirically. Different linear relationships having different slopes and intercepts were found for the low-carbon and stainless steel sheets, and the possible parameters affecting the correlation were discussed. It was shown that, within limits, yield and tensile strength of thin steel sheets can be predicted from the shear data obtained by the easy-to-perform SPT.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. G.E. Dieter, Mechanical Metallurgy, 3rd ed., McGraw-Hill, New York, 1986
2. R. Mahmudi and R. Mohammadi, Effect of Gauge Length on Uniaxial Deformation-Energy Components of Copper and Brass Sheets, J. Mater. Process. Technol., 2002, 121, p 185–19010.1016/S0924-0136(01)01036-6 ↗
3. A. Askariani, R. Mahmudi, and M.H. Pishbin, Comparison of Tearing Energy of Interstitial-Free (IF) and Low-Carbon (LC) Steel Sheets, Steel Res. Int., 2010, 81, p 1097–110110.1002/srin.201000129 ↗
4. T.M. Chang and H.W. Swift, Shearing of Metal Bars, J. Inst. Met., 1950, 78, p 119–146
5. R.K. Guduru, K.A. Darling, R. Kishore, R.O. Scattergood, C.C. Koch, and K.L. Murty, Evaluation of Mechanical Properties Using Shear-Punch Testing, Mater. Sci. Eng., A, 2005, 395, p 307–31410.1016/j.msea.2004.12.048 ↗
6. C.A. Leon and R.A.L. Drew, Small Punch Testing for Assessing the Tensile Strength of Gradient Al/Ni-SiC Composites, Mater. Lett., 2002, 56, p 812–81610.1016/S0167-577X(02)00619-5 ↗
7. P. Wanjara, R.A.L. Drew, and S. Yue, Application of Small Specimen Testing Technique for Mechanical Property Assessment of Discontinuously Reinforced Composites, Mater. Sci. Technol., 2006, 22, p 61–7110.1179/174328413X13789824293263 ↗
8. L. Zhang, A.M. Elwazri, T. Zimmerly, and M. Brochu, Shear Punch Testing and Fracture Toughness of Bulk Nanostructured Silver, Mater. Des., 2009, 30, p 1445–145010.1016/j.matdes.2008.08.012 ↗
9. R.K. Guduru, P.Z. Wong, K.A. Darling, C.C. Koch, K.L. Murty, and R.O. Scattergood, Determination of Activation Volume in Nanocrystalline Cu Using the Shear Punch Test, Adv. Eng. Mater., 2007, 9, p 855–85910.1002/adem.200700181 ↗
10. S.M. Kurtz, C.W. Jewett, J.S. Bergstrom, J.R. Foulds, and A.A. Edidin, Miniature Specimen Shear Punch Test for UHMWPE Used in Total Joint Replacements, Biomaterials, 2002, 23, p 1907–191910.1016/S0142-9612(01)00316-7 ↗
11. B. Kondori and R. Mahmudi, Effect of Ca Additions on the Microstructure, Thermal Stability and Mechanical Properties of a Cast AM60 Magnesium Alloy, Mater. Sci. Eng., A, 2010, 527, p 2014–202110.1016/j.msea.2009.11.043 ↗
12. G. Nayyeri and R. Mahmudi, Effects of Ca Additions on the Microstructural Stability and Mechanical Properties of Mg-5%Sn Alloy, Mater. Des., 2011, 32, p 1571–157610.1016/j.matdes.2010.09.019 ↗
13. R. Alizadeh and R. Mahmudi, Evaluating High-Temperature Mechanical Behavior of Cast Mg-4Zn-xSb Magnesium Alloys by Shear Punch Testing, Mater. Sci. Eng., A, 2010, 527, p 3975–398310.1016/j.msea.2010.03.007 ↗
14. R. Mahmudi, F. Kabirian, and Z. Nematollahi, Microstructural Stability and High-Temperature Mechanical Properties of AZ91 and AZ91+2RE Magnesium Alloys, Mater. Des., 2011, 32, p 2583–258910.1016/j.matdes.2011.01.040 ↗
15. H. Tao, W. Tong, L.G. Hector, Jr., and P.D. Zavattieri, Uniaxial Tensile and Simple Shear Behavior of Resistance Spot-Welded Dual-Phase Steel Joints, J. Mater. Eng. Perform., 2008, 17, p 517–53410.1007/s11665-007-9170-8 ↗
16. R.K. Guduru, A.V. Nagasekhar, R.O. Scattergood, C.C. Koch, and K.L. Murty, Finite Element Analysis of a Shear Punch Test, Metall. Mater. Trans. A, 2006, 37, p 1477–148310.1007/s11661-006-0092-0 ↗
17. S.M. Masoudpanah, R. Mahmudi, and T.G. Langdon, Correlation Between Shear Punch and Tensile Measurements for an AZ31Mg Alloy Processed by Equal-Channel Angular Pressing, Kovove Mater., 2011, 49, p 43–5010.4149/km_2011_1_43 ↗
18. G.E. Lucas, G.R. Odette, and J.W. Sheckherd, Shear Punch and Microhardness Tests for Strength and Ductility Measurements, ASTM STP, 1986, 888, p 112–140
19. G.E. Lucas, The Development of Small Specimen Mechanical Test Techniques, J. Nucl. Mater., 1983, 117, p 327–33910.1016/0022-3115(83)90041-7 ↗
20. M.L. Hamilton and M.B. Toloczko, Effect of Low Temperature Irradiation on the Mechanical Properties of Ternary V-Cr-Ti Alloys as Determined by Tensile Tests and Shear Punch Tests, J. Nucl. Mater., 2000, 283–287, p 488–49110.1016/S0022-3115(00)00227-0 ↗
21. M.L. Hamilton, M.B. Toloczko, and G.E. Lucas, Recent Progress in Shear Punch Testing, Miniaturized Specimens for Testing of Irradiated Materials, H. Ullmaier and P. Jung, Ed., Forschungszentrum Julich GmbH, Julich, Germany, 1995, p 46–58
22. G.L. Hankin, M.B. Toloczko, M.L. Hamilton, and R.G. Faulkner, Validation of the Shear Punch-Tensile Correlation Technique Using Irradiated Materials, J. Nucl. Mater., 1998, 258–263, p 1651–165610.1016/S0022-3115(98)00203-7 ↗