Effect of Molybdenum Content on Structural, Mechanical, and Tribological Properties of Hot Isostatically Pressed β-Type Titanium Alloys for Orthopedic Applications
Source abstract
Abstract
Aiming to develop alloys with better properties for orthopedic applications, the focus of the present research was to evaluate the effect of Mo at.% content on structural, mechanical, and tribological properties of hot isostatically pressed Ti-xMo (x = 4, 8, 12, 15, and 20 at.%) alloys. The structural evolution, mechanical properties, and tribological behavior of the nanostructured Ti-xMo alloys were evaluated using x-ray diffraction, scanning electron microscope, and ball-on-disk tribometer. Wear tests were conducted under different applied loads of 2, 8, and 16 N. Experimental results indicated that the structural evolution and morphological changes of the milled alloys were sensitive to their molybdenum (Mo) content. The morphological characterization showed that the crystallite size and the particle size decreased with increasing Mo content (at.%) reaching the lowest values of 27 and 26 nm in the case of Ti-15Mo and Ti-20Mo, respectively. On the other hand, the coefficient of friction and wear rates were found to be decreasing with increasing Mo content.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Orthopaedic implants and arthroplasty · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. M. Fellah, L. Aissani, A. Iost, A. Zairi, A. Montagne, and A. Mejias, Comportement à l’usure et au frottement de deux biomatériaux AISI, 316L et Ti6Al7Nb pour prothèse totale de hanche, Mater. Tech., 2018, 106(402), p 1–10. https://doi.org/10.1051/mattech/201805110.1051/mattech/2018051 ↗
2. A. Devaraj, S. Nag, R. Srinivasan, R.E.A. Williams, S. Banerjee, R. Banerjee, and H.L. Fraser, Experimental Evidence of Concurrent Compositional and Structural Instabilities Leading to ω Precipitation in Titanium-Molybdenum Alloys, Acta Mater., 2012, 60(2), p 596–60910.1016/j.actamat.2011.10.008 ↗
3. M. Fellah, M. Labaïz, O. Assala, L. Dekhil, and A. Iost, Tribological Behavior of Ti-6Al-4V and Ti-6Al-7Nb Alloys for Total Hip Prosthesis, Adv. Tribol., 2014, 7, Article ID 451387, p 13. https://doi.org/10.1155/2014/45138710.1155/2014/451387 ↗
4. M. Fellah, M. Labaïz, O. Assala, L. Dekhil, and A. Iost, Tribological Behavior of Biomaterial for Total Hip Prosthesis, Mater. Tech., 2014, 102(6–7), p 601–61210.1051/mattech/2014027 ↗
5. N. Hezil and M. Fellah, Synthesis, Structural and Mechanical Properties of Nanobioceramic (α-Al2O3), J. Aust. Ceram. Soc., 2019, 00(00), p 1–9. https://doi.org/10.1007/s41779-019-00333-710.1007/s41779-019-00333-7 ↗
6. A. Devaraj, R. Williams, S. Nag, R. Srinivasan, H. Fraser, and R. Banerjee, Investigations of Omega Precipitation in Titanium Molybdenum Alloys by Coupling 3D Atom Probe Tomography and High Resolution (S)TEM, Microsc. Microanal., 2009, 15(S2), p 268–26910.1017/S1431927609097086 ↗
7. M. Fellah, L. Aissani, M. Abdul Samad, M. Prakasam, A. Purnama, A. Montagne, A. Iost, and A. Mejias, Effect of Calcination Temperature on Friction and Wear Behavior of α-Alumina (α-Al2O3) for Biomedical Applications, Int. J. Appl. Ceram. Tech., 2019, 16, p 462–47010.1111/ijac.13116 ↗
8. J. Song, X. Zhang, X. Sun, H. Jiang, Z. Fan, C. Xie, and M.H. Wu, Effect of Aging on Superelastic Behaviors of a Metastable β Ti-Mo-Based Alloy, J. Mater. Eng. Perform., 2011, 21(3), p 366–37210.1007/s11665-011-9908-1 ↗
9. A. Devaraj, R.E.A. Williams, S. Nag, R. Srinivasan, H.L. Fraser, and R. Banerjee, Three-Dimensional Morphology and Composition of Omega Precipitates in a Binary Titanium-Molybdenum Alloy, Scripta Mater., 2009, 61(7), p 701–70410.1016/j.scriptamat.2009.06.006 ↗
10. X. Zhao, M. Niinomi, M. Nakai, and J. Hiea, Beta Type Ti-Mo Alloys with Changeable Young’s Modulus for Spinal fixation Applications, Acta Biomater., 2012, 8, p 1990–199710.1016/j.actbio.2012.02.004 ↗
11. F.F. Cardoso, P.L. Ferrandini, E.S.N. Lopes, A. Cremasco, and R. Caram, Ti-Mo Alloys Employed as Biomaterials: Effects of Composition and Aging Heat Treatment on Microstructure and Mechanical Behavior, J. Mech. Behav. Biomed. Mater., 2014, 32, p 31–3810.1016/j.jmbbm.2013.11.021 ↗
12. B.L. Wang, L. Li, and Y.F. Zheng, In Vitro Cytotoxicity and Hemocompatibility Studies of Ti-Nb, Ti-Nb-Zr and Ti-Nb-Hf Biomedical Shape Memory Alloys, Biomed. Mater., 2010, 5(04), p 044102–04410910.1088/1748-6041/5/4/044102 ↗
13. A. Ramarolahy, P. Castany, F. Prima, P. Laheurte, I. Peron, and T. Gloriant, Microstructure and Mechanical Behavior of Superelastic Ti-24Nb-0.5O and Ti-24Nb-0.5N Biomedical Alloys, J. Mech. Behav. Biomed. Mater., 2012, 9, p 83–9010.1016/j.jmbbm.2012.01.017 ↗
14. M. Conte, B. Pinedo, and A. Igartua, Frictional Heating Calculation Based on Tailored Experimental Measurements, Trib. Int., 2014, 74, p 1–610.1016/j.triboint.2014.01.020 ↗
15. V. Braic, M. Balaceanu, M. Braic, C. Vitelaru, I. Titorencu, V. Pruna, and A. Vladescu, Characterization of the Ti-10Nb-10Zr-5Ta Alloy for Biomedical Applications. Part 2: Wettability, Tribological Performance and Biocompatibility, J. Mater. Eng. Perform., 2013, 23(1), p 326–33210.1007/s11665-013-0738-1 ↗
16. E. Ghanbari, A. Zarei-Hanzaki, E. Farghadany, H.R. Abedi, and S. Khoddam, High-Temperature Deformation Characteristics of a β-Type Ti-29Nb-13Ta-4.6Zr Alloy, J. Mater. Eng. Perform., 2016, 25(4), p 1554–156110.1007/s11665-016-1953-3 ↗
17. M.A. Hussein, B. Yilbas, A.M. Kumar, R. Drew, and N. Al-Aqeeli, Influence of Laser Nitriding on the Surface and Corrosion Properties of Ti-20Nb-13Zr Alloy in Artificial Saliva for Dental Applications, J. Mater. Eng. Perform., 2018, 27, p 4655–466410.1007/s11665-018-3569-2 ↗
18. W.F. Ho, C.P. Ju, and J.H. Chern, Structure and Properties of Cast Binary Ti-Alloys, Biomaterials, 1999, 20(22), p 2115–212110.1016/S0142-9612(99)00114-3 ↗
19. N.T.C. Oliveira, G. Aleixo, R. Caram, and A.C. Guastaldi, Development of Ti-Mo all for Biomedical Applications: Microstructure and Electrochemical Characterition, Mater. Sci. Eng. A, 2007, 452–453, p 727–73110.1016/j.msea.2006.11.061 ↗
20. R. Kolli and A. Devaraj, A Review of Metastable Beta Titanium Alloys, Metals, 2018, 8(7), p 506–54710.3390/met8070506 ↗
21. W. Zhang, L. Yong, W. Hong, S. Min, Z. Tuo-yang, and Y. Tian-hang, Elastic Modulus of Phases in Ti-Mo Alloys, Mater. Charact., 2015, 106, p 302–30710.1016/j.matchar.2015.06.008 ↗
22. J.R. Martins, R.O. Arajo, R.A. Nogueira, and C.R. Grandini, Internal Friction and Microstructure of Ti and Ti-Mo Alloys Containing Oxygen, Arch. Metall. Mater., 2016, 61(1), p 25–3010.1515/amm-2016-0011 ↗
23. F.C. Flavia, L.F. Peterson, S.N. Eder, C. Alessandra, and C. Rubens, Ti-Mo Alloys Employed as Biomaterials: Effects of Composition and Aging Heat Treatment on Microstructure and Mechanical Behavior, J. Mech. Behav. Biomed. Mater, 2014, 32, p 31–3810.1016/j.jmbbm.2013.11.021 ↗
24. D. Yang, Z. Guo, H. Shao, X. Liu, and Y. Ji, Mechanical Properties of Porous Ti-Mo and Ti-Nb Alloys for Biomedical Application by Gelcasting, Proc. Eng., 2012, 36, p 160–16710.1016/j.proeng.2012.03.025 ↗
25. A. Devaraj, V.V. Joshi, A. Srivastava, S. Manandhar, V. Moxson, V.A. Duz, and C. Lavender, A Low-Cost Hierarchical Nanostructured Beta-Titanium Alloy with High Strength, Nat. Commun., 2016, 7, p 1117610.1038/ncomms11176 ↗
26. M.K. Ibrahim, E. Hamzah, and S.N. Saud, Microstructure, Phase Transformation, Mechanical Behavior, Bio-corrosion and Antibacterial Properties of Ti-Nb-xSn (x = 0, 0.25, 0.5 and 1.5) SMAs, J. Mater. Eng. Perform., 2018, 20, p 218. https://doi.org/10.1007/s11665-018-3776-x10.1007/s11665-018-3776-x ↗
27. R. Davis, H.M. Flower, and D.R. West, The Decomposition of Ti-Mo Alloy Martensites by Nucleation and Growth and Spinodal Mechanisms, Acta Metall. Mater., 1979, 27, p 1041–105210.1016/0001-6160(79)90192-5 ↗
28. P.L. Ferrandini, F.F. Cardoso, S.A. Souza, C.R. Afonso, and R. Caram, Aging Response of the Ti-35Nb-7Zr-5Ta and Ti-35Nb-7Ta Alloys, J. Alloys Compd., 2007, 433, p 207–21010.1016/j.jallcom.2006.06.094 ↗
29. C. Lee, M. Ju, C.P. Chern, and J.H. Lin, Structure–Property Relationship of Cast Ti-Nb Alloys, J. Oral Rehabil., 2002, 29, p 314–32210.1046/j.1365-2842.2002.00825.x ↗
30. Y. Mantani, Y. Takemoto, M. Hida, A. Sakakibara, and M. Tajima, Phase Transformation of α´´ Martensite Structure by Aging in Ti-8 mass% Mo Alloy, Mater. Trans. JIM, 2004, 45, p 1629–163410.2320/matertrans.45.1629 ↗
31. F. Sun, F. Prima, and T. Gloriant, High-Strength Nanostructured Ti-12Mo Alloy from Ductile Metastable Beta State Precursor, Mater. Sci. Eng. A, 2010, 527, p 4262–426910.1016/j.msea.2010.03.044 ↗
32. A.B. Elshalakany, S. Ali, A. Amigó Mata, A.K. Eessaa, P. Mohan, T.A. Osman, and V. Amigó Borrás, Microstructure and Mechanical Properties of Ti-Mo-Zr-Cr Biomedical Alloys by Powder Metallurgy, J. Mater. Eng. Perform., 2017, 26(3), p 1262–127110.1007/s11665-017-2531-z ↗
33. Z.Y. He, L. Zhang, W.R. Shan, Y.Q. Zhang, Y.H. Jiang, R. Zhou, and J. Tan, Characterizations on Mechanical Properties and In Vitro Bioactivity of Biomedical Ti-Nb-Zr-CPP Composites Fabricated by Spark Plasma Sintering, Acta. Metall. Sin. (Engl. Lett.), 2016, 29(11), p 1073–108010.1007/s40195-016-0486-y ↗
34. M. Fellah, M. Labaïz, O. Assala, L. Dekhil, and A. Iost, Friction and Wear Behavior of Ti-6Al-7Nb Biomaterial Alloy, J. Biomater. Nanobiotechnol., 2013, 4(4), p 374–38410.4236/jbnb.2013.44047 ↗
35. Z. Gao, Q. Li, F. He, Y. Huang, and Y. Wan, Mechanical Modulation and Bioactive Surface Modification of Porous Ti-10Mo Alloy for Bone Implants, Mater. Des., 2012, 42, p 13–2010.1016/j.matdes.2012.05.041 ↗
36. M. Fellah, A. Linda, M. Abdul Samed, and A. Montagne, Effect of Replacing Vanadium by Nobium and Iron on the Tribological Behavior of HIPed Titanium Alloys, Acta Metall. Sin. (Engl. Lett.), 2017, 30(11), p 1089–109910.1007/s40195-017-0652-x ↗
37. A. Attanasio, M. Gelfi, A. Pola, E. Ceretti, and C. Giardini, Influence of Material Microstructures in Micromilling of Ti-6Al-4V Alloy, Materials., 2013, 6, p 4268–428310.3390/ma6094268 ↗
38. M. Nouari and H. Makich, On the Physics of Machining Titanium Alloys: Interactions Between Cutting Parameters, Microstructure and Tool Wear, Metals, 2014, 4, p 335–35810.3390/met4030335 ↗
39. L.J. Xu, Y.Y. Chen, Z.C. Liu, and F.T. Kong, The Microstructure and Properties of Ti-Mo-Nb Alloys for Biomedical Applications, J. Alloys Compd., 2008, 453, p 320–32410.1016/j.jallcom.2006.11.144 ↗
40. M. Fellah, M. Labaïz, O. Assala, and A. Iost, Comparative Friction and Wear Behavior Between Titanium Alloys Ti-6Al-7Nb and Ti-6A1-4V, Proceeding of 5th World Tribology Congress, WTC, 2013, 1, p 470–47310.1155/2014/451387 ↗
41. M. Fellah, M. Labaïz, O. Assala, L. Dekhil, and A. Iost, Tribological Behavior of Biomaterials for Total Hip Prosthesis, Trends. Biomater. Artif. Organs., 2015, 29(01), p 22–30
42. C. Suryanarayana, and M. Grant Norton, X-ray Diffraction: A Practical Approach, Plenum Press, New York, XIII, (2014), p 273
43. L. Aissani, M. Fellah, C. Nouveau, and M. Abdul Samad, Structural and Mechanical Properties of Cr-Zr-N Coatings with Different Zr Content, Surf. Eng., 2017, 33, p 1–10. https://doi.org/10.1080/02670844.2017.133837810.1080/02670844.2017.1338378 ↗
44. P. Sochacka, A. Miklaszewski, and M. Jurczyk, Development of β-Type Ti-x at.% Mo Alloys by Mechanical Alloying and Powder Metallurgy: Phase Evolution and Mechanical Properties (10 ≤ x ≤ 35), J. Alloys Compd., 2019, 776, p 370–37810.1016/j.jallcom.2018.10.217 ↗
45. G. Dercz, I. Matuła, J. Maszybrocka, M. Zubko, J. Barczyk, L. Pająk, and S. Stach, Effect of Milling Time and Presence of Sn on the Microstructure and Porosity of Sintered Ti-10Ta-8Mo and Ti-10Ta-8Mo-3Sn Alloys, J. Alloys Compd., 2019, 791, p 232–24710.1016/j.jallcom.2019.03.287 ↗
46. M. Razavi, M.R. Rahimipour, and A.H. Rajabi, Synthesis of Nano Crystalline TiC Powder from Impure Ti Chips Via Mechanical Alloying, J. Alloys Compd., 2000, 436, p 142–14510.1016/j.jallcom.2006.07.018 ↗
47. T. Nilson, C. Oliveira, A. Giorgia, C. Rubens, and C. Antonio, Development of Ti-Mo Alloys for Biomedical Applications: Microstructure and Electrochemical Characterization, Mater. Sci. Eng. A, 2007, 452–453, p 727–731
48. J.W. Elmer, T.A. Palmer, S.S. Babub, and E.D. Specht, In Situ Observations of Lattice Expansion and Transformation Rates of α and β Phases in Ti-6Al-4V, Mater. Sci. Eng. A, 2005, 391, p 104–11310.1016/j.msea.2004.08.084 ↗
49. M. Fellah, O. Assala, and M. Labaiz, Comparative Study on Tribiological Behavior of Ti-6Al-7Nb and SS AISI, 316L Alloys, for Total Hip Prosthesis, TMS 2014 Suppl. Proc., 2014, 32, p 237–246
50. M. Fellah, L. Aissani, and M. Abdul Samed, Friction and Wear of Biomaterials Alloys AISI, 316L and Ti-6Al-7Nb, Trends. Biomater. Artif. Organs., 2016, 30(2), p 106–115
51. M. Fellah, M. Labaïz, O. Assala, L. Dekhil, and A. Iost, Tribological Behavior of AISI, 316L Stainless Steel for Biomedical Applications, Tribol. Mater. Surf. Interfaces, 2013, 7(3), p 135–14910.1179/1751584X13Y.0000000032 ↗
52. M.F. Lopez, J.A. Jimenez, and A. Gutierrez, Corrosion Study of Surface-Modified Vanadium-Free Titanium Alloys, Electrochim. Acta, 2003, 48, p 1395–140110.1016/S0013-4686(03)00006-9 ↗
53. D. Lin, J.H.C. Lin, and C.P. Ju, Structure and Properties of Ti-75Mo-xFe, Alloys, Biomaterials, 2002, 23, p 1723–173010.1016/S0142-9612(01)00233-2 ↗
54. L.J. Xu, Y.Y. Chen, Z.G. Liu, and F.T. Kong, The Microstructure and Properties of Ti-Mo-Nb Alloys for Biomedical Applications, J. Alloys Compd., 2008, 453, p 320–32410.1016/j.jallcom.2006.11.144 ↗
55. M. Fellah, N. Hezil, M. Abdul Samad, M.Z. Touhami, A. Montagne, A. Iost, A. Mejias, and S. Kossman, The Effect of Milling Time on Structural, Friction and Wear Behavior of Hot Isostatically Pressed Ti-Ni Alloys for Orthopedic Applications, TMS 2019 148th Annual Meeting & Exhibition Supplemental Proceedings. 2019, 85, p. 865–875 https://doi.org/10.1007/978-3-030-05861-6_8510.1007/978-3-030-05861-6_85 ↗
56. N. Kang, Y. Li, X. Lin, E. Feng, and W. Huang, Microstructure and Tensile Properties of Ti-Mo Alloys Manufactured Via Using Laser Powder Bed Fusion, J. Alloys Compd., 2019, 771, p 877–88410.1016/j.jallcom.2018.09.008 ↗
57. L. Bolzoni, E.M. Ruiz-Navas, and E. Gordo, Processing of Elemental Titanium by Powder Metallurgy Techniques, Mater. Sci. Forum, 2013, 765, p 338–383
58. M. Fellah, L. Aissani, M. Abdul Samad, A. Iost, and A. Montagne, Characterization of R.F Magnetron Sputtered Cr-N, Cr-Zr-N and Zr-N Coatings, Trans. IMF, 2017, 95(05), p 261–26810.1080/00794236.2017.1339464 ↗
59. M. Fellah, M. Abdul Samed, M. Labaïz, O. Assala, L. Dekhil, and A. Iost, Sliding Friction and Wear Performance of the Nano-Bioceramic α-Al2O3 Prepared by High Energy Milling, Tribol. Int., 2015, 91, p 151–15910.1016/j.triboint.2015.07.006 ↗