Comparison of Roller Burnishing Method with Other Hole Surface Finishing Processes Applied on AISI 304 Austenitic Stainless Steel
Source abstract
Abstract
Component surface quality and selection of the optimum material are the main factors determining the performance of components used in machine manufacturing. The level of hole surface quality can be evaluated by the measurements regarding surface roughness, micro-hardness, and cylindricity. In this study, data had been obtained for different hole drilling methods. The characteristics of materials obtained after applications were compared for different hole-finishing processes to identify best hole drilling method. AISI 304 austenitic stainless steel material was used. Surface finishing of holes were performed using drilling, turning, reaming, grinding, honing, and roller burnishing methods. The results of the study show that the roller burnishing method gives the best results for mechanical, metallurgical properties, and hole surface quality of the material. On the other hand, the worst characteristics were obtained in the drilling method.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Advanced machining processes and optimization · Erosion and Abrasive Machining
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. A.M. Hassan and A.S. AL-Bsharat, Influence of Burnishing Process on Surface Roughness Hardness and Microstructure of Some Nonferrous Metals, Wear, 1996, 199, p 1–810.1016/0043-1648(95)06847-3 ↗
2. M. El-Air, An Investigation into Roller Burnishing, Int. J. Mach. Tools Manuf., 2000, 40, p 1603–161710.1016/S0890-6955(00)00019-5 ↗
3. N.R.K. Ellenberger, I. Nester, U. Liu, G.Y. Schulte, and R.O. Ritchie, On the İnfluence of Mechanical Surface Treatments—Deep Rolling and Laser Shock Peening—on the Fatigue Behaviour of Ti-6Al-4V at Ambient and Elevated Temperatures, Elsevier, Mater. Sci. Eng. A, 2003, 355, p 216–23010.1016/S0921-5093(03)00069-8 ↗
4. M.H. Axir and A.A. Ibrahim, Some Surface Characteristics Due to Centre Rest Ball Burnishing, J. Mater. Process. Technol., 2005, 167, p 47–5310.1016/j.jmatprotec.2004.09.078 ↗
5. H. Czichos, Tribology, a System Approach to the Science and Technology of Friction Lubrication and Wear, Elsevier, 1978, p 130–132
6. B.J. Hamrock and D. Dowson, Isothermal Elastohydrodynamic Lubrication of Point Contacts, Part III: Fully Flooded Results, J. Lubrication Technol., 1977, 13, p 264–27610.1115/1.3453074 ↗
7. A.M. Hassan and O.M. AI-Wahhab, Surface Characteristics of Some Roller Burnished Non-ferrous Components, Mater. Manuf. Process., 1998, 13(4), p 505–51510.1080/10426919808935272 ↗
8. S. Thamizhmnaii, B.B. Omar, S. Saparudin, and S. Hasan, Surface Roughness İnvestigation and Hardness by Burnishing on Titanium Alloy, J. Achiev. Mater. Manuf. Eng., 2008, 28, p 139–142
9. C.Y. Binu and B. Ramamoorthy, An Investigation into the High Performance of TiN-Coated Rollers in Burnishing Process, J. Mater. Process. Technol., 2008, 207, p 350–35510.1016/j.jmatprotec.2008.06.058 ↗
10. T.A. El-Taweel and M.H. El-Axir, Analysis and Optimization of the Ball Burnishing Process Through the Taguchi Technique, Int. J. Adv. Manuf. Technol., 2009, 41, p 301–31010.1007/s00170-008-1485-6 ↗
11. K. Pałka, A. Weroński, and K. Zaleski, Mechanical Properties and Corrosion Resistance of Burnished X5CrNi 18-9 Stainless Steel, J. Achiev. Mater. Manuf. Eng., 2006, 16, p 57–62
12. M.A. Korzynski and J. Pacana, Fatigue Strength of Chromium Coated Elements and Possibility of İts İmprovement with Slide Diamond Burnishing, Surf. Coat. Technol., 2009, 203, p 1670–167610.1016/j.surfcoat.2008.12.022 ↗
13. F.J. Shiou and C. Hsu, Surface Finishing of Hardened and Tempered Stainless Tool Steel Using Sequential Ball Grinding, Ball Burnishing and Ball Polishing Processes on a Machining Centre, J. Mater. Process. Technol., 2008, 205, p 249–25810.1016/j.jmatprotec.2007.11.244 ↗
14. N.H. Loh and S.C. Tam, Effects of Ball Burning Parameters on Surface Finish: A Literature Survey and Discussion, Prec. Eng., 1988, 10(4), p 215–22010.1016/0141-6359(88)90056-6 ↗
15. O.M. Abd AL-Wahhab, “The Effects of Roller-Burnishing on Some Properties of Non-Ferrous Metals,” M.Sc. Thesis, Jordan University of Science and Technology, 1996
16. U. Pettersson and S. Jacobson, Influence of Surface Texture on Boundary Lubricated Sliding Contact, Tribol. Int., 2003, 36(8), p 57–6410.1016/S0301-679X(03)00104-X ↗
17. R.L. Murthy and B. Kotiveerachari, Burnishing of Metallic Surfaces a Review, Prec. Eng., 1981, 3, p 172–17910.1016/0141-6359(81)90010-6 ↗
18. R. Rajasekariah and S. Vaidyanathan, Increasing the Wear-Resistance of Steel Components by Ball Burnishing, Wear, 1975, 34, p 183–18810.1016/0043-1648(75)90064-2 ↗
19. U.S. Dixit and P.M. Dixit, A Study of Residual Stresses in Rolling, Int. J. Mach. Tools Manuf., 1997, 37(6), p 837–85310.1016/S0890-6955(96)00052-1 ↗
20. S.W. Bouzid, N.B. Salah, and J.L. Lebrun, Influence of Machining by Finishing Milling on Surface Characteristics, J. Mach. Tools Manuf., 2001, 41, p 443–45010.1016/S0890-6955(00)00069-9 ↗
21. Y.K. Chou, Hard Turning of M50 Steel with Different Microstructures in Continuous and Intermittent Cutting, Wear, 2003, 225, p 1388–139410.1016/S0043-1648(03)00102-9 ↗
22. Yu.G. Shneider, Characteristics of Burnished Components, Mach. Tooling, 1967, 38(1), p 19–22
23. K.H. Zum-Gahr, Microstructure and Wear of Materials, Elsevier, 1987, p 80–82
24. F. Klocke, E. Brinksmeier, and K. Weinert, Capability Profile of Hard Cutting and Grinding Processes, Ann. CIRP, 2005, 54, p 557–580
25. P. Zhang and J. Lindemann, Effect of Roller Burnishing on the High Cycle Fatigue Performance of the High-Strength Wrought Magnesium Alloy AZ80, Scr. Mater., 2005, 52, p 1011–101510.1016/j.scriptamat.2005.01.026 ↗
26. S. Thamizhmanii and B. Saparudin, A Study of Multi-Roller Burnishing on Non-Ferrous Metals, J. Achiev. Mater. Manuf. Eng., 2007, 22, p 95–98