Effect of Deposition Sequence on Microstructure and Properties of 316L and Inconel 625 Bimetallic Structure by Wire Arc Additive Manufacturing
Source abstract
Abstract
Wire arc additive manufacturing based on cold metal transfer was applied to deposit 316L and Inconel 625 bimetallic structures in this work. The effect of deposition sequence on the microstructure and properties of the bimetallic structure was emphatically studied. The results showed that with the increase in the number of deposition layers, the morphology of δ-ferrite in 316L changed from lath to skeleton, and the amount of Laves phase in Inconel 625 increased. When depositing 316L first and then depositing Inconel 625 (316L-Inconel 625), the interface was well bonded with no defects. However, at the interface of the other bimetallic structure (Inconel 625-316L), plenty of Laves phases rich in Nb and Mo elements appeared, and there were two cracks propagating along the interface to the 316L and Inconel 625 deposition side, which were attributed to the diffusion of Cr and Ni elements and the Laves phase. The fracture of the 316L-Inconel 625 tensile samples occurred on the 316L side, which was a ductile fracture. The Inconel 625-316L tensile samples broke at the interface due to the cracks, which was a mixture of brittle and ductile fracture.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. S. Ramesh Kumar, K.S. Akhilendar, S. Sandeep and P. Aravind, Investigation on Microstructural Behavior and Mechanical Properties of Plasma Arc Welded Dissimilar Butt Joint of Austenitic-Ferritic Stainless Steels, Mater. Today Proc., 2018, 5, p 8008–8015.10.1016/j.matpr.2017.11.485 ↗
2. M.K. Samal, M. Seidenfuss, E. Roos and K. Balani, Investigation of Failure Behavior of Ferritic-Austenitic Type of Dissimilar Steel Welded Joints, Eng. Fail. Anal., 2011, 18, p 999–1008.10.1016/j.engfailanal.2010.12.011 ↗
3. J.N. Hu, T. Fukahori, T. Igari, Y. Chuman and A.C.F. Cocks, An Evaluation of Creep Rupture Strength of Ferritic/Austenitic Dissimilar Weld Interfaces Using Cohesive Zone Modelling, Procedia Struct. Integr., 2016, 2, p 934–941.10.1016/j.prostr.2016.06.120 ↗
4. E.M. Anawa and A.G. Olabi, Optimization of Tensile Strength of Ferritic/Austenitic Laser-Welded Components, Opt. Lasers Eng., 2008, 46, p 571–577.10.1016/j.optlaseng.2008.04.014 ↗
5. N. Ghosh, P.K. Pal and G. Nandi, GMAW Dissimilar Welding of AISI 409 Ferritic Stainless Steel to 316L Austenitic Stainless Steel by Using AISI 308 Filler Wire, Eng. Sci. Technol., 2017, 20, p 1334–1341.
6. A. Mortezaie and M. Shamanian, An Assessment of Microstructure, Mechanical Properties and Corrosion Resistance of Dissimilar Welds between Inconel 718 and 310S Austenitic Stainless Steel, Int. J. Press. Vessels Pip., 2014, 116, p 37–46.10.1016/j.ijpvp.2014.01.002 ↗
7. G.N. Ahmad, M.S. Raza, N.K. Singh and H. Kumar, Experimental Investigation on Ytterbium Fiber Laser Butt Welding of Inconel 625 and Duplex Stainless Steel 2205 Thin Sheets, Opt. Lasers Technol., 2020, 126, p 106–117.10.1016/j.optlastec.2020.106117 ↗
8. L.L. Wang, J.X. Xue and Q. Wang, Correlation between Arc Mode, Microstructure, and Mechanical Properties during Wire Arc Additive Manufacturing of 316L Stainless Steel, Mater. Sci. Eng. A., 2019, 751, p 183–190.10.1016/j.msea.2019.02.078 ↗
9. Y.F. Wang, X.Z. Chen and C.C. Su, Microstructure and Mechanical Properties of Inconel 625 Fabricated by Wire-arc Additive Manufacturing, Surf. Coat. Technol., 2019, 374, p 116–123.10.1016/j.surfcoat.2019.05.079 ↗
10. D.K. Kim, W. Woo, E.Y. Kim and S.H. Choi, Microstructure and Mechanical Characteristics of Multi-layered Materials Composed of 316L Stainless Steel and Ferritic Steel Produced by Direct Energy Deposition, J. Alloys Compd., 2019, 774, p 896–907.10.1016/j.jallcom.2018.09.390 ↗
11. R. Duraisamy, S. Mohan Kumar, A. Rajesh Kannan, N. Siva Shanmugam, K. Sankaranarayanasamy and M.R. Ramesh, Tribological Performance of Wire Arc Additive Manufactured 347 Austenitic Stainless Steel under Unlubricated Conditions at Elevated Temperatures, J. Manuf. Process., 2020, 56, p 306–321.10.1016/j.jmapro.2020.04.073 ↗
12. D.X. Wen, P. Long, J.J. Li, L. Huang and Z.Z. Zheng, Effects of Linear Heat Input on Microstructure and Corrosion Behavior of An Austenitic Stainless Steel Processed by Wire Arc Additive Manufacturing, Vacuum, 2020, 173, p 109–131.10.1016/j.vacuum.2019.109131 ↗
13. X.H. Chen, J. Li, X. Cheng, B. He, H.M. Wang and Z. Huang, Microstructure and Mechanical Properties of the Austenitic Stainless Steel 316L Fabricated by Gas Metal Arc Additive Manufacturing, Mater. Sci. Eng. A., 2017, 703, p 567–577.10.1016/j.msea.2017.05.024 ↗
14. Y.F. Wang, X.Z. Chen, Q.K. Shen, C.C. Su, Y.P. Zhang, S. Jayalakshmi and R. Arvind Singh, Effect of Magnetic Field on the Microstructure and Mechanical Properties of Inconel 625 Superalloy Fabricated by Wire Arc Additive Manufacturing, J. Manuf. Process., 2021, 64, p 10–19.10.1016/j.jmapro.2021.01.008 ↗
15. M.R.U. Ahsan, X.S. Fan, G.J. Seo, C. Ji, M. Noakes, A. Nycz, P.K. Liaw and D.B. Kim, Microstructures and Mechanical Behavior of the Bimetallic Additively-manufactured Structure (BAMS) of Austenitic Stainless Steel and Inconel 625, J. Mater. Sci. Technol., 2021, 74, p 176–188.10.1016/j.jmst.2020.10.001 ↗
16. D.W. Rathod, S. Pandey, P.K. Singh and R. Prasad, Experimental Analysis of Dissimilar Metal Weld Joint: Ferritic to Austenitic Stainless Steel, Mater. Sci. Eng. A., 2015, 639, p 259–268.10.1016/j.msea.2015.05.011 ↗
17. M. Mukherjee and T.K. Pal, Influence of Heat Input on Martensite Formation and Impact Property of Ferritic-Austenitic Dissimilar Weld Metals, J. Mater. Sci. Technol., 2012, 28(4), p 343–352.10.1016/S1005-0302(12)60066-8 ↗
18. Y. Javadi, M.C. Smith, K. Abburi Venkata, N. Naveed, A.N. Forsey, J.A. Francis, R.A. Ainsworth, C.E. Truman, D.J. Smith, F. Hosseinzadeh, S. Gungor, P.J. Bouchard, H.C. Dey, A.K. Bhaduri and S. Mahadevan, Residual Stress Measurement Round Robin on An Electron Beam Welded Joint between Austenitic Stainless Steel 316L(N) and Ferritic Steel P91, Int. J. Press Vessels Pip., 2017, 154, p 41–57.10.1016/j.ijpvp.2017.06.002 ↗
19. M. Roskosz, Metal Magnetic Memory Testing of Welded Joints of Ferritic and Austenitic Steels, NDT&E Int., 2011, 44, p 305–310.10.1016/j.ndteint.2011.01.008 ↗
20. S.K. Rajput, A. Kumar, S.S. Tripathi and E. Sachan, Investigation of Microstructural Behavior and Mechanical Properties of Dissimilar Weld Joints of Austenitic-ferritic Stainless Steel, Mater. Today. Proc., 2020, 25, p 778–784.10.1016/j.matpr.2019.09.018 ↗
21. C.C. Su, X.Z. Chen, C. Gao and Y.F. Wang, Effect of Heat Input on Microstructure and Mechanical Properties of Al-Mg Alloys Fabricated by WAAM, Appl. Surf. Sci., 2019, 486, p 431–440.10.1016/j.apsusc.2019.04.255 ↗
22. J.S. Zuback, T.A. Palmer and T. DebRoy, Additive Manufacturing of Functionally Graded Transition Joints between Ferritic and Austenitic Alloys, J. Alloy. Compd., 2019, 770, p 995–1003.10.1016/j.jallcom.2018.08.197 ↗
23. B. Parvaresh, R. Miresmaeili and M. Yazdizadeh, Characterization of Wire Arc Additive Manufactured Products: A Comparison between as-deposited and Inter-layer Cold Worked Specimens, J. Manuf. Process., 2020, 57, p 61–71.10.1016/j.jmapro.2020.05.053 ↗
24. Q.K. Shen, X.D. Kong and X.Z. Chen, Fabrication of Bulk Al-Co-Cr-Fe-Ni High-entropy Alloy Using Combined Cable Wire Arc Additive Manufacturing (CCW-AAM): Microstructure and Mechanical Properties, J. Mater. Sci. Technol., 2021, 74, p 136–142.10.1016/j.jmst.2020.10.037 ↗
25. L.B. Sun, F.C. Jiang, R.S. Huang, D. Yuan, Y. Su, C.H. Guo and J.D. Wang, Investigation on the Process Window with Liner Energy Density for Single-layer Parts Fabricated by Wire and Arc Additive Manufacturing, J. Manuf. Process., 2020, 56, p 898–907.10.1016/j.jmapro.2020.05.054 ↗
26. Y.H. Zhou, X. Lin, N. Kang, W.D. Huang, J. Wang and Z.N. Wang, Influence of Travel Speed on Microstructure and Mechanical Properties of Wire + Arc Additively Manufactured 2219 Aluminum Alloy, J. Mater. Sci. Technol., 2020, 37, p 143–153.10.1016/j.jmst.2019.06.016 ↗
27. T. Hauser, A.D. Silva, R.T. Reisch, J. Volpp, T. Kamps and A.F.H. Kaplan, Fluctuation Effects in Wire Arc Additive Manufacturing of Aluminium Analysed by High-speed Imaging, J. Manuf. Process., 2020, 56, p 1088–1098.10.1016/j.jmapro.2020.05.030 ↗
28. X. Tang, S. Zhang, X. Cui, C.H. Zhang, Y. Liu and J.B. Zhang, Tribological and Cavitation Erosion Behaviors of Nickel-based and Iron-based Coatings Deposited on AISI 304 Stainless Steel by Cold Metal Transfer, J. Mater. Res. Technol., 2020, 9(3), p 6665–6681.10.1016/j.jmrt.2020.04.064 ↗
29. B.T. Wu, Z.J. Qiu, Z.X. Pan, K. Carpenter, T. Wang, D.H. Ding, S.V. Duin and H.J. Li, Enhanced Interface Strength in Steel-nickel Bimetallic Component Fabricated Using Wire Arc Additive Manufacturing with Interweaving Deposition Strategy, J. Mater. Sci. Technol., 2020, 52, p 226–234.10.1016/j.jmst.2020.04.019 ↗
30. T. Abe and H. Sasahara, Dissimilar Metal Deposition with A Stainless Steel and Nickel-based Alloy Using Wire and Arc-based Additive Manufacturing, Precis. Eng., 2016, 45, p 387–395.10.1016/j.precisioneng.2016.03.016 ↗
31. C. Fang, J. Wei and J. Liu, Solidifcation Cracking Sensibility of Narrow Gap Laser Welding on ITER-grade Austenitic Stainless Steel, Fusion Eng. Des., 2021, 162, p 112068.10.1016/j.fusengdes.2020.112068 ↗
32. G. Moskal, D. Niemieca, B. Chmielaa, P. Kałamarza, T. Durejkob, M. Ziętalab and T. Czujko, Microstructural Characterization of Laser-cladded NiCrAlY Coatings on Inconel 625 Ni-based Superalloy and 316L Stainless Steel, Surf. Coat. Technol., 2020, 387, p 125317.10.1016/j.surfcoat.2019.125317 ↗