Numerical Investigation of the Effect of Rolling on the Localized Stress and Strain Induction for Wire + Arc Additive Manufactured Structures
Source abstract
Abstract
Cold rolling can be used in-process or post-process to improve microstructure, mechanical properties and residual stress in directed-energy-deposition techniques, such as the high deposition rate wire + arc additive manufacturing (WAAM) process. Finite element simulations of the rolling process are employed to investigate the effect of rolling parameters, in particular rolling load and roller profile radius on the residual stress field as well as plastic strain distribution for the profiled roller. The results show the response to rolling of commonly used structural metals in WAAM, i.e., AA2319, S335JR steel and Ti-6Al-4V, taking into account the presence of residual stresses. The rolling load leads to changes in the location and the maximum value of the compressive residual stresses, as well as the depth of the compressive residual stresses. However, the roller profile radius only changes the maximum value of these compressive residual stresses. Changing the rolling load influences the equivalent plastic strain close to the top surface of the wall as well as in deeper areas, whereas the influence of the roller profile radius is negligible. The plastic strain distribution is virtually unaffected by the initial residual stresses prior to rolling. Finally, design curves were generated from the simulations for different materials, suggesting ideal rolling load and roller profile combinations for microstructural improvement requiring certain plastic strains at a specific depth of the additive structure.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. S.W. Williams, F. Martina, A.C. Addison, J. Ding, G. Pardal, and P. Colegrove, Wire + Arc Additive Manufacturing, J. Mater. Sci. Technol., 2015, 32, p 641–647. https://doi.org/10.1179/1743284715Y.000000007310.1179/1743284715Y.0000000073 ↗
2. C.R. Cunningham, J.M. Flynn, A. Shokrani, V. Dhokia, and S.T. Newman, Invited Review Article: Strategies and Processes for High Quality Wire Arc Additive Manufacturing, Addit. Manuf., 2018, 22, p 672–686. https://doi.org/10.1016/j.addma.2018.06.02010.1016/j.addma.2018.06.020 ↗
3. LASIMM Project (2018), http://www.lasimm.eu . Accessed 13 Aug 2018
4. J. Ding, P. Colegrove, J. Mehnen, S. Ganguly, P.M.S. Almeida, F. Wang, and S.W. Williams, Thermo-Mechanical Analysis of Wire and Arc Additive Layer Manufacturing Process on Large Multi-layer Parts, Comput. Mater. Sci., 2011, 50, p 3315–3322. https://doi.org/10.1016/j.commatsci.2011.06.02310.1016/j.commatsci.2011.05.020 ↗
5. J. Zhang, X. Wang, S. Paddea, and X. Zhang, Fatigue Crack Propagation Behaviour in Wire + Arc Additive Manufactured Ti-6Al-4V: Effects of Microstructure and Residual Stress, Mater. Des., 2016, 90, p 551–561. https://doi.org/10.1016/j.matdes.2015.10.14110.1016/j.matdes.2015.10.141 ↗
6. J.R. Hönnige, P. Colegrove, S. Ganguly, E. Eimer, S. Kabra, and S.W. Williams, Control of Residual Stress and Distortion in Aluminium Wire + Arc Additive Manufacture with Rolling, Addit. Manuf., 2018, 22, p 775–783. https://doi.org/10.1016/j.addma.2018.06.01510.1016/j.addma.2018.06.015 ↗
7. J. Ding, P. Colegrove, J. Mehnen, S.W. Williams, F. Wang, and P.M.S. Almeida, A Computationally Efficient Finite Element Model of Wire and Arc Additive Manufacture, Int. J. Adv. Manuf. Technol., 2014, 70, p 227–236. https://doi.org/10.1007/s00170-013-5261-x10.1007/s00170-013-5261-x ↗
8. P. Colegrove, H.E. Coules, J. Fairman, F. Martina, T. Kashoob, H. Mamash, and L.D. Cozzolino, Microstructure and Residual Stress Improvement in Wire and Arc Additively Manufactured Parts Through High-Pressure Rolling, J. Mater. Process. Technol., 2013, 213, p 1782–1791. https://doi.org/10.1016/j.jmatprotec.2013.04.01210.1016/j.jmatprotec.2013.04.012 ↗
9. J.R. Hönnige, S.W. Williams, M.J. Roy, P. Colegrove, and S. Ganguly, Residual Stress Characterization and Control in the Additive Manufacture of Large Scale Metal Structures, in 10th International Conference on Residual Stress, Sydney (2016). https://doi.org/10.21741/9781945291173-7710.21741/9781945291173-77 ↗
10. F. Martina, M.J. Roy, B.A. Szost, S. Terzi, P. Colegrove, S.W. Williams, P.J. Withers, J. Meyer, and M. Hofmann, Residual Stress of As-Deposited and Rolled Wire + Arc Additive Manufacturing Ti-6Al-4V Components, Mater. Sci. Technol., 2016, 32, p 1439–1448. https://doi.org/10.1080/02670836.2016.114270410.1080/02670836.2016.1142704 ↗
11. B.A. Szost, S. Terzi, F. Martina, D. Boisselier, A. Prytuliak, T. Pirling, M. Hofmann, and D.J. Jarvis, A Comparative Study of Additive Manufacturing Techniques: Residual Stress and Microstructural Analysis of CLAD and WAAM Printed Ti-6Al-4V Components, Mater. Des., 2016, 89, p 559–567. https://doi.org/10.1016/j.matdes.2015.09.11510.1016/j.matdes.2015.09.115 ↗
12. J.R. Hönnige, P. Colegrove, B. Ahmad, M.E. Fitzpatrick, S. Ganguly, T.L. Lee, and S.W. Williams, Residual Stress and Texture Control in Ti-6Al-4V Wire + Arc Additively Manufactured Intersections by Stress Relief and Rolling, Mater. Des., 2018, 150, p 193–205. https://doi.org/10.1016/j.matdes.2018.03.06510.1016/j.matdes.2018.03.065 ↗
13. F. Wang, S. Williams, P. Colegrove, and A.A. Antonysamy, Microstructure and Mechanical Properties of Wire and Arc Additive Manufactured Ti-6Al-4V, Metall. Mater. Trans. A, 2012, 44, p 968–977. https://doi.org/10.1007/s11661-012-1444-610.1007/s11661-012-1444-6 ↗
14. J. Donoghue, A.A. Antonysamy, F. Martina, P. Colegrove, S.W. Williams, and P.B. Prangnell, The Effectiveness of Combining Rolling Deformation with Wire–Arc Additive Manufacture on β-Grain Refinement and Texture Modification in Ti-6Al-4V, Mater. Charact., 2016, 114, p 103–114. https://doi.org/10.1016/j.matchar.2016.02.00110.1016/j.matchar.2016.02.001 ↗
15. J. Gu, J. Ding, S.W. Williams, H. Gu, P. Ma, and Y. Zhai, The Effect of Inter-layer Cold Working and Post-deposition Heat Treatment on Porosity in Additively Manufactured Aluminum Alloys, J. Mater. Process. Technol., 2016, 230, p 26–34. https://doi.org/10.1016/j.jmatprotec.2015.11.00610.1016/j.jmatprotec.2015.11.006 ↗
16. J. Gu, J. Ding, S.W. Williams, H. Gu, P. Ma, and Y. Zhai, The Strengthening Effect of Inter-Layer Cold Working and Post-deposition Heat Treatment on the Additively Manufactured Al-6.3Cu Alloy, Mater. Sci. Eng., A, 2016, 651, p 18–26. https://doi.org/10.1016/j.msea.2015.10.10110.1016/j.msea.2015.10.101 ↗
17. P. Colegrove, J. Donoghue, F. Martina, J. Gu, P. Prangnell, and J.R. Hönnige, Application of Bulk Deformation Methods for Microstructural and Material Property Improvement and Residual Stress and Distortion Control in Additively Manufactured Components, Scr. Mater., 2017, 135, p 111–118. https://doi.org/10.1016/j.scriptamat.2016.10.03110.1016/j.scriptamat.2016.10.031 ↗
18. Y. Lei, N.P. O’Dowd, and G.A. Webster, Fracture Mechanics Analysis of a Crack in a Residual Stress Field, Int. J. Fract., 2000, 106, p 195–216. https://doi.org/10.1023/A:102657440085810.1023/A:1026574400858 ↗
19. C. Charles and N. Jarvstrat, Finite element modelling of microstructure on GTAW metal deposition of Ti-6Al-4V alloy, in Proceedings of the 3rd International Conference on Mathematical Modeling and Information Technologies in Welding and Related Processes (2006), pp. 151–156
20. R. Pan, T. Pirling, J. Zheng, J. Lin, and C.M. Davies, Quantification of Thermal Residual Stresses Relaxation in AA7xxx Aluminium Alloy through Cold Rolling, J. Mater. Process. Technol., 2018, 264, p 454–468. https://doi.org/10.1016/j.jmatprotec.2018.09.03410.1016/j.jmatprotec.2018.09.034 ↗
21. R. Sun, L. Li, Y. Zhu, W. Guo, P. Peng, B. Cong, J. Sun, Z. Che, B. Li, C. Guo, and L. Liu, Microstructure, Residual Stress and Tensile Properties Control of Wire–Arc Additive Manufactured 2319 Aluminum Alloy with Laser Shock Peening, J. Alloys Compd., 2018, 747, p 255–265. https://doi.org/10.1016/j.jallcom.2018.02.35310.1016/j.jallcom.2018.02.353 ↗
22. A.M. Thompson, M. Fresini, J. Dos Santos, J. Hedgegard, U. Dithey, I.M. Richardson, and D. Yapp, Improving the Competitiveness of the European Steel Fabrication Industry Using Synchronised Tandem Wire Welding Technology, vol. 80224 (2008). https://doi.org/10.2777/1085
23. B.E. Carroll, T.A. Palmer, and A.M. Beese, Anisotropic Tensile Behavior of Ti-6Al-4V Components Fabricated with Directed Energy Deposition Additive Manufacturing, Acta Mater., 2015, 87, p 309–320. https://doi.org/10.1016/j.actamat.2014.12.05410.1016/j.actamat.2014.12.054 ↗
24. Y. Chen, S. Sun, and C. Ji, Analysis of Aluminum Sheets with Multiple Sites Damage Based on Fatigue Tests and DIC Technique, Int. J. Fatigue, 2018, 109, p 37–48. https://doi.org/10.1016/j.ijfatigue.2017.12.00810.1016/j.ijfatigue.2017.12.008 ↗
25. D. Castagnetti, A. Spaggiari, and E. Dragoni, Assessment of the Cohesive Contact Method for the Analysis of Thin-Walled Bonded Structures, Int. J. Adhes. Adhes., 2012, 37, p 112–120. https://doi.org/10.1016/j.ijadhadh.2012.01.01210.1016/j.ijadhadh.2012.01.012 ↗
26. X. Wang, X. Gong, and K. Chou, Scanning Speed Effect on Mechanical Properties of Ti6Al-4V Alloy Processed by Electron Beam Additive Manufacturing, in 43rd Proceedings of the North American Manufacturing Research Institution (2015), pp. 287–295. https://doi.org/10.1016/j.promfg.2015.09.02610.1016/j.promfg.2015.09.026 ↗
27. J. Mehnen, J. Ding, H. Lockett, and P. Kazanas, Design Study for Wire and Arc Additive Manufacture, Int. J. Prod. Dev., 2014, 19, p 2–20. https://doi.org/10.1504/IJPD.2014.06002810.1504/IJPD.2014.060028 ↗
28. F. Montevecchi, G. Venturini, A. Scippa, and G. Campatelli, Finite Element Modelling of Wire–Arc-Additive-Manufacturing Process, Procedia CIRP, 2016, 55, p 109–114. https://doi.org/10.1016/j.procir.2016.08.02410.1016/j.procir.2016.08.024 ↗
29. X. Bai, H. Zhang, and G. Wang, Modeling of the Moving Induction Heating Used as Secondary Heat Source in Weld-Based Additive Manufacturing, Int. J. Adv. Manuf. Technol., 2015, 77, p 717–727. https://doi.org/10.1007/s00170-014-6475-210.1007/s00170-014-6475-2 ↗
30. F. Shu, Y. Lv, Y. Liu, F. Xu, Z. Sun, P. He, and B. Xu, Residual Stress Modeling of Narrow Gap Welded Joint of Aluminum Alloy by Cold Metal Transferring Procedure, Constr. Build. Mater., 2014, 54, p 224–235. https://doi.org/10.1016/j.conbuildmat.2013.12.05610.1016/j.conbuildmat.2013.12.056 ↗
31. A.M. Korsunsky, The Modelling of Residual Stresses due to Surface Peening Using Eigenstrain Distributions, J. Strain Anal. Eng. Des., 2005, 40(2005), p 817–824. https://doi.org/10.1243/030932405X3098410.1243/030932405X30984 ↗
32. A.M. Korsunsky, Residual Elastic Strain due to Laser Shock Peening: Modelling by Eigenstrain Distribution, J. Strain Anal. Eng. Des., 2006, 41, p 195–204. https://doi.org/10.1243/03093247JSA14110.1243/03093247JSA141 ↗
33. T.S. Jun and A.M. Korsunsky, Evaluation of Residual Stresses and Strains Using the Eigenstrain Reconstruction Method, Int. J. Solids Struct., 2010, 47, p 1678–1686. https://doi.org/10.1016/j.ijsolstr.2010.03.00210.1016/j.ijsolstr.2010.03.002 ↗
34. B. Klusemann, R. Denzer, and B. Svendsen, Microstructure Based Modeling of Residual Stresses in WC-12Co-Sprayed Coatings, J. Therm. Spray Technol., 2012, 21, p 96–107. https://doi.org/10.1007/s11666-011-9690-510.1007/s11666-011-9690-5 ↗
35. T. Mukherjee, W. Zhang, and T. DebRoy, An Improved Prediction of Residual Stresses and Distortion in Additive Manufacturing, Comput. Mater. Sci., 2017, 126, p 360–372. https://doi.org/10.1016/j.commatsci.2016.10.00310.1016/j.commatsci.2016.10.003 ↗
36. B. AlMangour, D. Grzesiak, and J.M. Yang, Nanocrystalline TiC-Reinforced H13 Steel Matrix Nanocomposites Fabricated by Selective Laser Melting, Mater. Des., 2016, 96, p 150–161. https://doi.org/10.1016/j.matdes.2016.02.02210.1016/j.matdes.2016.02.022 ↗
37. L.D. Cozzolino, H.E. Coules, P. Colegrove, and S. Wen, Investigation of Post-weld Rolling Methods to Reduce Residual Stress and Distortion, J. Mater. Process. Technol., 2017, 247, p 243–256. https://doi.org/10.1016/j.jmatprotec.2017.04.01810.1016/j.jmatprotec.2017.04.018 ↗
38. J. Foehrenbach, V. Hardenacke, and M. Farajian, High Frequency Mechanical Impact Treatment (HFMI) for the Fatigue Improvement: Numerical and Experimental Investigations to Describe the Condition in the Surface Layer, Weld. World, 2016, 60, p 749–755. https://doi.org/10.1007/s40194-016-0338-410.1007/s40194-016-0338-4 ↗
39. F. Martina, P. Colegrove, S.W. Williams, and J. Meyer, Microstructure of Interpass Rolled Wire + Arc Additive Manufacturing Ti-6Al-4V Components, Metall. Mater. Trans. A, 2015, 46, p 6103–6118. https://doi.org/10.1007/s11661-015-3172-110.1007/s11661-015-3172-1 ↗
40. J.R. Hönnige, Thermo-mechanical Control of Residual Stress, Distortion and Microstructure in Wire + Arc Additively Manufactured Ti-6Al-4V, PhD Thesis, Cranfield University, Cranfield, 2018
41. A.R. McAndrew, M.A. Rosales, P. Colegrove, J.R. Hönnige, A. Ho, R. Fayolle, K. Eyitayo, I. Stana, P. Sukrongpang, A. Crochemore, and Z. Pinter, Interpass Rolling of Ti-6Al-4V Wire + Arc Additively Manufactured Features for Microstructural Refinement, Addit. Manuf., 2018, 21, p 340–349. https://doi.org/10.1016/j.addma.2018.03.00610.1016/j.addma.2018.03.006 ↗
42. W. Guo, R. Sun, B. Song, Y. Zhu, F. Li, Z. Che, B. Li, C. Guo, L. Liu, and P. Peng, Laser Shock Peening of Laser Additive Manufactured Ti6Al4V Titanium Alloy, Surf. Coat. Technol., 2018, 349, p 503–510. https://doi.org/10.1016/j.surfcoat.2018.06.02010.1016/j.surfcoat.2018.06.020 ↗
43. S. Luo, W. He, K. Chen, X. Nie, L. Zhou, and Y. Li, Regain the Fatigue Strength of laser Additive Manufactured Ti Alloy Via Laser Shock Peening, J. Alloys Compd., 2018, 750, p 625–635. https://doi.org/10.1016/j.jallcom.2018.04.02910.1016/j.jallcom.2018.04.029 ↗
44. B. Cong, J. Ding, and S.W. Williams, Effect of Arc Mode in Cold Metal Transfer Process on Porosity of Additively Manufactured Al-6.3%Cu Alloy, Int. J. Adv. Manuf. Technol., 2015, 76, p 1593–1606. https://doi.org/10.1007/s00170-014-6346-x10.1007/s00170-014-6346-x ↗
45. F. Martina, J. Mehnen, S.W. Williams, P.A. Colegrove, and F. Wang, Investigation of the Benefits of Plasma Deposition for the Additive Layer Manufacture of Ti-6Al-4V, J. Mater. Process. Technol., 2012, 212, p 1377–1386. https://doi.org/10.1016/j.jmatprotec.2012.02.00210.1016/j.jmatprotec.2012.02.002 ↗
46. X. Xu, S. Ganguly, J. Ding, C.E. Seow, and S.W. Williams, Enhancing Mechanical Properties of Wire + Arc Additively Manufactured INCONEL 718 Superalloy Through In-Process Thermomechanical Processing, Mater. Des., 2018, 160, p 1042–1051. https://doi.org/10.1016/j.matdes.2018.10.03810.1016/j.matdes.2018.10.038 ↗
47. J.R. Hönnige, P.A. Colegrove, and S.W. Williams, Improvement of Microstructure and Mechanical Properties of Wire + Arc Additively Manufactured Ti-6Al-4V with Machine Hammer Peening, Procedia Eng., 2017, 216, p 8–17. https://doi.org/10.1016/j.proeng.2018.02.08310.1016/j.proeng.2018.02.083 ↗
48. P.M.S. Almeida, Innovative Process Model of Ti-6Al-4V Additive Layer Manufacturing Using Cold Metal Transfer (CMT), in Proccedings 21st Annual International Solid Freeform Fabrication Symposium (2010)
49. M. Froend, S. Riekehr, N. Kashaev, B. Klusemann, and J. Enz, Process Development for Wire-Based Laser Metal Deposition of 5087 Aluminium Alloy by Using Fibre Laser, J. Manuf. Process., 2018, 34, p 721–732. https://doi.org/10.1016/j.jmapro.2018.06.03310.1016/j.jmapro.2018.06.033 ↗