Effect of Pulse Parameters on Weld Quality in Pulsed Gas Metal Arc Welding: A Review
Source abstract
Abstract
The weld quality comprises bead geometry and its microstructure, which influence the mechanical properties of the weld. The coarse-grained weld microstructure, higher heat-affected zone, and lower penetration together with higher reinforcement reduce the weld service life in continuous mode gas metal arc welding (GMAW). Pulsed GMAW (P-GMAW) is an alternative method providing a better way for overcoming these afore mentioned problems. It uses a higher peak current to allow one molten droplet per pulse, and a lower background current to maintain the arc stability. Current pulsing refines the grains in weld fusion zone with increasing depth of penetration due to arc oscillations. Optimum weld joint characteristics can be achieved by controlling the pulse parameters. The process is versatile and easily automated. This brief review illustrates the effect of pulse parameters on weld quality.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Additive Manufacturing Materials and Processes · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (83)
Show source-provided references
1. P.K. Palani and N. Murugan, Development of Mathematical Models for Prediction of Weld Bead Geometry in Cladding by Flux Cored Arc Welding, Int. J. Adv. Manuf. Technol., 2006, 30(7–8), p 669–67610.1007/s00170-005-0101-2 ↗
2. E. Karadeniz, U. Ozsarac, and C. Yildiz, The Effect of Process Parameters on Penetration in Gas Metal Arc Welding Processes, Mater. Des., 2007, 28(2), p 649–65610.1016/j.matdes.2005.07.014 ↗
3. K. Ishizaki, Interfacial Tension Theory of the Phenomenon of Arc Welding-Mechanism of Penetration, Proceedings of Symposium on Physics of Arc Welding, The Institute of Welding, London, 1962, p 195–209
4. D.S. Nagesh and G.L. Datta, Prediction of Weld Bead Geometry and Penetration in Shielded Metal-Arc Welding Using Artificial Neural Networks, J. Mater. Process. Technol., 2002, 123(2), p 303–31210.1016/S0924-0136(02)00101-2 ↗
5. G. Powell and G. Herfurth, Charpy V-Notch Properties and Microstructures of Narrow Gap Ferritic Welds of a Quenched and Tempered Steel Plate, Metall. Mater. Trans. A, 1998, 29(11), p 2775–278410.1007/s11661-998-0318-4 ↗
6. V.S.R. Murti, P.D. Srinivas, G.H.D. Banadeki, and K.S. Raju, Effect of Heat Input on the Metallurgical Properties of HSLA Steel in Multi-Pass MIG Welding, J. Mater. Process. Technol., 1993, 37(1–4), p 723–72910.1016/0924-0136(93)90131-O ↗
7. M. Eroglu, M. Aksoy, and N. Orhan, Effect of Coarse Initial Grain Size on Microstructure and Mechanical Properties of Weld Metal and HAZ of a Low Carbon Steel, Mat. Sci. Eng. A, 1999, 269(1), p 59–6610.1016/S0921-5093(99)00137-9 ↗
8. A.S. Shahi, S. Pandey, and J.S. Gill, Effect of Auxiliary Preheating of Filler Wire on Dilution in Gas Metal Arc Stainless Steel Surfacing Using RSM, Surf. Eng., 2007, 23(5), p 384–39010.1179/174329407X247127 ↗
9. Y.C. Lin and K.H. Lee, Effect of Preheating on the Residual Stress in Type 304 Stainless Steel Weldment, J. Mater. Process. Technol., 1997, 63(1–3), p 797–80110.1016/S0924-0136(96)02727-6 ↗
10. T. Mohandas, G. Madhusudan Reddy, and B. Satish Kumar, Heat-Affected Zone Softening in High-Strength Low-Alloy Steels, J. Mater. Process. Technol., 1999, 88(1), p 284–29410.1016/S0924-0136(98)00404-X ↗
11. T. Nakamura and K. Hiraoka, Ultranarrow GMAW Process with Newly Developed Wire Melting Control System, Sci. Technol. Weld. Join., 2001, 6(6), p 355–36210.1179/stw.2001.6.6.355 ↗
12. H. Tong, T. Ueyama, S. Harada, and M. Ushio, Quality and Productivity Improvement in Aluminium Alloy Thin Sheet Welding Using Alternating Current Pulsed Metal Inert Gas Welding System, Sci. Technol. Weld. Join., 2001, 6(4), p 203–20810.1179/136217101101538776 ↗
13. Z. Smati, Automatic Pulsed MIG Welding, Mater. Construct., 1986, 18, p 38r–44r
14. K. Stanzel, Pulsed GMAW Cuts Cycle Time by 600 Percent, Weld. Des. Fabr., 2001, April, p 85–87
15. J. Tippins, Box Beam Fabrication Using the Pulsed MIG Process, Mater. Construct. Br. Weld. J., 1970, December, p 547–550
16. R.C. Harvey, Gas Metal Arc Welding Fume Generation Using Pulsed Current, Weld. J., 1995, 74(11), p 59s–68s
17. M. Thamodharan, H.P. Beck, and A. Wolf, Steady and Pulsed Direct Current Welding With a Single Converter, Weld. J., 1999, 78(3), p 75s–79s
18. A. Raja, Flux Core Stelliting by Pulsed MAG Welding, WRI, J., 1998, 19(3), p 98–101
19. I.E. French and M.R. Bosworth, A Comparison of Pulsed and Conventional Welding With Basic Flux Cored and Metal Cored Welding Wires, Weld. J., 1995, 74(6), p 197s–205s
20. M. Jilong and R.L. Apps, New MIG Process Results from Metal Transfer Mode Control, Weld. Met. Fabr., 1983, 51, p 168–175
21. B. Bernard, Effects of Shielding Gas in Pulsed MIG Welding, Join. Mater., 1989, June, p 277–280
22. J.A. Lambert, Assessment of the Pulsed GMA Technique for Tube Attachment Welding, Weld. J., 1989, 68(2), p 35–43
23. S. Ueguri, K. Hara, and H. Komura, Study of Metal Transfer in Pulsed GMA Welding, Weld. J., 1985, 64(8), p 242s–250s
24. M. Amin, Pulsed Current Parameters for Arc Stability and Controlled Metal Transfer in Arc Welding, Met. Construct., 1983, 15, p 272–278
25. P. Boughton and J.A. Lucey, The Use of Pulsed Current to Control Metal Transfer in Welding, Br. Weld. J., 1965, 4, p 159–166
26. C.J. Allum, Welding Technology Data: Pulsed MIG Welding Weld, Met. Fabr., 1985, 53, p 24–30
27. Y.S. Kim, “Metal Transfer in Gas Metal Arc Welding,” PhD Thesis MIT, Cambridge, MA, 1989.
28. P. Mike and Kemppi, Power Sources for Pulsed MIG Welding, Join. Mater., 1989, June, p 268–271
29. S. Subramaniam, D.R. White, J.E. Jones, and D.W. Lyons, Droplet Transfer in Pulsed Gas Metal Arc Welding Of Aluminum, Weld. J., 1998, 77(11), p 458s–463s
30. S. Rajasekaran, Method of Selecting The Most Suitable Combination of Parameters in Pulsed Current Gas Metal Arc Welding Process, Proceedings of International Conference on Advances in Mechanical and Industrial Engineering, Roorkee, 1997, p 1115–1122.
31. M. Amin, Synergic Pulse MIG Welding, Met. Construct., 1981, 6, p 349–353
32. C.J. Allum, MIG Welding—Time for a Reassessment, Met. Construct., 1983, June, p 347–353
33. S. Rajasekaran, S.D. Kulkarni, U.D. Mallya, and R.C. Chaturvedi, Droplet Detachment and Plate Fusion Characteristics in Pulsed Current Gas Metal Arc Welding, Weld. J., 1998, 77(6), p 254s–269s
34. S. Rajasekaran, Surface Topography of Pulsed Current Gas Metal Arc Clads, Surf. Eng., 2000, 16(6), p 495–50010.1179/026708400101517503 ↗
35. M. Suban and J. Tusek, Methods for the Determination of Arc Stability, J. Mater. Process. Technol., 2003, 143–144, p 430–43710.1016/S0924-0136(03)00416-3 ↗
36. N. Jacobsen, Monopulse Investigation of Drop Detachment in Pulsed Gas Metal Arc Welding, J. Phys. D, 1992, 25, p 783–79710.1088/0022-3727/25/5/007 ↗
37. P. Boughton and T.M. Matani, Two Years of Pulsed Arc Welding, Weld. Met. Fabricat., 1967, October, p 410–420
38. M.R. Bosworth, Effective Heat Input in Pulsed Gas Metal Arc Welding With Solid Wire Electrodes, Weld. J., 1991, 70(5), p 111s–117s
39. P.K. Ghosh, L. Dorn, M. Hubner, and V.K. Goyal, Arc Characteristics and Behaviour of Metal Transfer in Pulsed Current GMA Welding of Aluminium Alloy, J. Mater. Process. Technol., 2007, 194(1–3), p 163–17510.1016/j.jmatprotec.2007.04.113 ↗
40. Y.M. Zhang, E. Liguo, and B.L. Walcott, Robust Control of Pulsed Gas Metal Arc Welding, J. Dyn. Syst. Meas. Control. ASME, 2000, 124, p 1–9
41. H.C. De Miranda, A. Scotti, and V.A. Ferraresi, Identification and Control of Metal Transfer in Pulsed GMAW Using Optical Sensor, Sci. Technol. Weld. Join., 2007, 12(3), p 249–25710.1179/174329307X164229 ↗
42. P. Praveen, P.K.D.V. Yarlagadda, and M.J. Kang, Advancements in Pulse Gas Metal Arc Welding, J. Mater. Process. Technol., 2005, 164–165, p 1113–111910.1016/j.jmatprotec.2005.02.100 ↗
43. P.K. Palani and N. Murugan, Modeling and Simulation of Wire Feed Rate For Steady Current and Pulsed Current Gas Metal Arc Welding Using 317L Flux Cored Wire, Int. J. Adv. Manuf. Technol., 2007, 34(11–12), p 1111–111910.1007/s00170-006-0678-0 ↗
44. S. Subramaniam, D.R. White, J.E. Jones, and D.W. Lyons, Experimental Approach to Selection of Pulsing Parameters in Pulsed GMAW, AWS, Weld. J., 1999, 78(5), p 166s–172s
45. J.F. Collard, Adaptive Pulsed GMAW Control: The Digital Pulse System, Weld. J., 1998, 77(11), p 35s–38s
46. P.K. Ghosh, P.C. Gupta, and V.K. Goyal, Stainless Steel Cladding of Structural Steel Plate Using the Pulsed Current GMAW Process, Weld. J., 1998, 77(7), p 307s–314s
47. J.C. Needham, Pulse Controlled Consumable Electrode Welding Arcs—General Principles and Operating Characteristics, Br. Weld. J., 1965, 4, p 191–197
48. P.K. Ghosh, S.R. Gupta, and H.S. Randhawa, Characteristics of a Pulsed-Current, Vertical-Up Gas Metal Arc Weld in Steel, Metall. Mater. Trans. A, 2000, 31A, p 2247–225910.1007/s11661-000-0142-y ↗
49. P.K. Ghosh and P.C. Gupta, Use of Pulse Current MIG Welding Improves the Weld Characteristics of Al–Zn–Mg Alloy, Indian Weld. J., 1996, April, p 24–3210.22486/iwj.v29i2.182648 ↗
50. Y.S. Kim and T.W. Eagar, Metal Transfer in Pulsed Current Gas Metal Arc Welding, Weld. J., 1993, 72(7), p 279s–287s
51. L.O. Vilarinho and A. Scotti, An Alternate Algorithm for Synergic Pulsed GMAW of Aluminum, Australas. Weld. J., 2000, 45, p 36–44
52. W.G. Essers and V. Gompal, Arc control with Pulsed GMA Welding, Weld. J., 1984, 64(6), p 26s–32s
53. S. Rajasekaran, Weld Bead Characteristics in Pulsed GMA Welding of Al–Mg Alloys, Weld. J., 1999, 78(12), p 397s–407s
54. P.K. Palani and N. Murugan, Selection of Parameters of Pulsed Current Gas Metal Arc Welding (Review), J. Mater. Process. Technol., 2006, 172, p 1–1010.1016/j.jmatprotec.2005.07.013 ↗
55. A. Joseph, D. Farson, D. Harwig, and R. Richardson, Influence of GMAW-P Current Waveforms on Heat Input and Weld Bead Shape, Sci. Technol. Weld. Join., 2005, 10(3), p 311–31810.1179/174329305X40624 ↗
56. J.C. Needham and A.W. Carter, Material Transfer Characteristics with Pulsed Current, Br. Weld. J., 1965, 5, p 229–241
57. C.S. Wu, M.A. Chen, and Y.F. Lu, Effect of Current Waveforms on Metal Transfer in Pulsed Gas Metal Arc Welding, Meas. Sci. Technol., 2005, 16(12), p 2459–246510.1088/0957-0233/16/12/009 ↗
58. I.S. Kim, A. Basu, and E. Siores, Mathematical Models for Control of Weld Bead Penetration in the GMAW Process, Int. J. Adv. Manuf. Technol., 1996, 12(6), p 393–40110.1007/BF01186927 ↗
59. C.J. Allum and L. Quintino, Control of Fusion Characteristics in Pulsed Current MIG Welding, Meter. Construct., 1985, April, p 242r–245r
60. M. Nouri, A. Abdollah-Zadehy, and F. Malek, Effect of Welding Parameters on Dilution and Weld Bead Geometry in Cladding, J. Mater. Sci. Technol., 2007, 23(6), p 817–822
61. H. Ian and N. John, Pulsed MIG/MAG Welding, Join. Mater., 1989, June, p 264–281
62. V.K. Goyal, P.K. Ghosh, and J.S. Saini, Analytical Studies on Thermal Behaviour and Geometry of Weld Pool in Pulsed Current Gas Metal Arc Welding, J. Mater. Process. Technol., 2008, 209(3), p 1318–133610.1016/j.jmatprotec.2008.03.035 ↗
63. P.K. Ghosh, S.R. Gupta, P.C. Gupta, and R. Rathi, Fatigue Characteristics of Pulsed MIG Welded Al-Zn-Mg Alloy, J. Mater. Sci., 1991, 26(22), p 6161–617010.1007/BF01113899 ↗
64. T. Ishida, Stainless Steel Modification on a Mild Steel by Pulsed-Current Arc, J. Mater. Sci. Lett., 1992, 11(2), p 83–8510.1007/BF00724605 ↗
65. K.H. Tseng and C.P. Chou, The Effect of Pulsed GTA Welding on the Residual Stress of a Stainless Steel Weldment, J. Mater. Process. Technol., 2002, 123(3), p 346–35310.1016/S0924-0136(02)00004-3 ↗
66. P.K. Ghosh and B.K. Rai, Characteristics of Pulsed Current Bead on Plate Deposit in Flux Cored GMAW Process, ISIJ Int., 1996, 36(8), p 1036–104510.2355/isijinternational.36.1036 ↗
67. H.S. Randhawa, P.K. Ghosh, and S.R. Gupta, Geometrical Characteristics of Pulsed Current Positional GMA Weld, ISIJ Int., 1998, 38(3), p 276–28410.2355/isijinternational.38.276 ↗
68. H.S. Randhawa, P.K. Ghosh, and S.R. Gupta, Some Basic Aspects of Geometrical Characteristics of Pulsed Current Vertical-up GMA Weld, ISIJ Int., 2000, 40(1), p 71–7610.2355/isijinternational.40.71 ↗
69. P.K. Ghosh, S.G. Kulkarni, M. Kumar, and H.K. Dhiman, Pulsed Current GMAW for Superior Weld Quality of Austenitic Stainless Steel Sheet, ISIJ Int., 2007, 47(1), p 138–14510.2355/isijinternational.47.138 ↗
70. V.K. Goyal, P.K. Ghosh, and J.S. Saini, Influence of Pulse Parameters on Characteristics of Bead-on-Plate Weld Deposits of Aluminum and Its Alloy in the Pulsed Gas Metal Arc Welding Process, Metall. Mater. Trans. A, 2008, 39(13), p 3260–327510.1007/s11661-008-9637-8 ↗
71. R. Kumar, U. Dilthey, D.K. Dwivedi, S.P. Sharma, and P.K. Ghosh, Welding of Thin Sheet of Al Alloy (6082) by Using Vario Wire DC P-GMAW, Int. J. Adv. Manufact. Technol., 2009, 42(1–2), p 102–11710.1007/s00170-008-1568-4 ↗
72. R. Kumar, U. Dilthey, D.K. Dwivedi, and P.K. Ghosh, Thin Sheet Welding of Al 6082 Alloy by AC Pulse-GMA and AC Wave Pulse-GMA Welding, Mater. Des., 2009, 30(2), p 306–31310.1016/j.matdes.2008.04.073 ↗
73. P.K. Ghosh and A.K. Ghosh, Control of Residual Stresses Affecting Fatigue Life of Pulsed Current Gas-Metal-Arc Weld of High-Strength Aluminium Alloy, Metall. Mater. Trans. A, 2004, 35(8), p 2439–244410.1007/s11661-006-0224-6 ↗
74. C.L.M. Silva and A. Scotti, The Influence of Double Pulse on Porosity Formation in Aluminum GMAW, J. Mater. Process. Technol., 2006, 171(3), p 366–37210.1016/j.jmatprotec.2005.07.008 ↗
75. M. Sireesha, V. Shankar, S.K. Albert, and S. Sundaresan, Microstructural Features of Dissimilar Welds Between 316LN Austenitic Stainless Steel and Alloy 800, Mat. Sci. Eng. A, 2000, 292(1), p 74–8210.1016/S0921-5093(00)00969-2 ↗
76. A. Gural, B. Bostan, and A.T. Ozdemir, Heat Treatment in Two Phase Region and its Effect on Microstructure and Mechanical Strength after Welding of a Low Carbon Steel, Mater. Des., 2007, 28(3), p 897–90310.1016/j.matdes.2005.10.005 ↗
77. G. Lothongkum, E. Viyanit, and P. Bhandhubanyong, Study on the Effects of Pulsed TIG Welding Parameters on Delta-Ferrite Content, Shape Factor and Bead Quality in Orbital Welding of AISI, 316L Stainless Steel Plate, J. Mater. Process. Technol., 2001, 110(2), p 233–23810.1016/S0924-0136(00)00875-X ↗
78. S.H. Wang, P.K. Chiu, J.R. Yang, and J. Fang, Gamma (γ) Phase Transformation in Pulsed GTAW Weld Metal of Duplex Stainless Steel, Mater. Sci. Eng., 2006, 420(1–2), p 26–3310.1016/j.msea.2006.01.028 ↗
79. V. Balasubramanian, V. Ravisankar, and G. Madhusudhan Reddy, Effect of Pulsed Current Welding on Fatigue Behaviour of High Strength Aluminium Alloy Joints, Mater. Des., 2008, 29(2), p 492–50010.1016/j.matdes.2006.12.015 ↗
80. V. Balasubramanian, V. Ravisankar, and G. Madhusudhan Reddy, Effect of Pulsed Current Welding on Mechanical Properties of High Strength Aluminum Alloy, Int. J. Adv. Manuf. Technol., 2008, 36(3–4), p 254–26210.1007/s00170-006-0848-0 ↗
81. V. Balasubramanian, V. Ravisankar, and G. Madhusudhan Reddy, Effect of Pulsed Current and Post Weld Aging Treatment on Tensile Properties of Argon Arc Welded High Strength Aluminium Alloy, Mater. Sci. Eng., 2007, 459(1–2), p 19–3410.1016/j.msea.2006.12.125 ↗
82. G. Padmanabham, M. Schaper, S. Pandey, and E. Simmchen, Tensile and Fracture Behavior of Pulsed Gas Metal Arc-Welded Al-Cu-Li, Weld. J., 2007, 86(6), p 147s–160s
83. S. Kou, Welding Metallurgy, 2nd ed., Wiley Interscience Publication, 2002, p 145–430.10.1002/0471434027 ↗