journal article·2024-06-01Open access

Characterizing the Effect of Filament Moisture on Tensile Properties and Morphology of Fused Deposition Modeled Polylactic Acid/Polybutylene Succinate Parts

Raihan Quader, Evan Dramko, David Grewell, Jed Randall, Lokesh Karthik Narayanan

Abstract

Moisture absorption into hygroscopic/hydrophilic materials used in fused deposition modeling (FDM) can diminish desired mechanical properties. Sensitivity to moisture is dependent on material properties and environmental factors and needs characterization. In this article, moisture sensitivity of four grades of polylactic acid (PLA) filaments and four different ratios of PLA/polybutylene succinate (PBS) blended filaments were characterized through FDM printed American society for testing and materials (ASTM-D638) test samples after conditioning the filaments at different relative humidity levels. The tensile testing and scanning electron microscopy (SEM) of the samples' fracture surfaces revealed that PLA 4043D was the most moisture-sensitive among the chosen grades of PLA filaments. Through filament tension test and melt flow index (MFI) testing it was observed that moisture had a significant detrimental effect (20% reduction in tensile strength and 50% increase in MFI) on PLA 4043D filaments. Samples from moisture-conditioned PLA/PBS 75/25 blended filaments displayed a significant reduction (10%) in tensile strength. Moreover, the MFI of 75/25 filaments was increased with subsequent increases in moisture level. Investigation of tensile properties of ASTM samples made from four grades of PLA filaments exposed to room temperature and humidity conditions for 3 months showed an even more significant decrease in strength (ranging from 24% to 36%).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · biodegradable polymer synthesis and properties · Microplastics and Plastic Pollution

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Industrial and Manufacturing Engineering, North Dakota State University, Fargo, North Dakota, USA.

Department of Computer Science, North Dakota State University, Fargo, North Dakota, USA.

NatureWorks, LLC, Minnetonka, Minnesota, USA.

References (38)

Show source-provided references
1. 10.1016/j.compositesb.2016.11.03410.1016/j.compositesb.2016.11.034 ↗
2. 10.3390/jmmp303006410.3390/jmmp3030064 ↗
3. 10.1089/3dp.2015.003610.1089/3dp.2015.0036 ↗
4. 10.1089/3dp.2017.003910.1089/3dp.2017.0039 ↗
5. 10.1089/3dp.2020.005210.1089/3dp.2020.0052 ↗
6. 10.1016/j.matdes.2019.10808910.1016/j.matdes.2019.108089 ↗
7. 10.1016/j.engfracmech.2020.10722510.1016/j.engfracmech.2020.107225 ↗
8. 10.1016/j.engfracmech.2022.10876610.1016/j.engfracmech.2022.108766 ↗
9. 10.1016/j.tafmec.2020.10249710.1016/j.tafmec.2020.102497 ↗
10. 10.1016/j.tafmec.2022.10352710.1016/j.tafmec.2022.103527 ↗
11. 10.1016/S0141-3910(97)00148-110.1016/S0141-3910(97)00148-1 ↗
12. 10.1016/j.addr.2016.06.01810.1016/j.addr.2016.06.018 ↗
13. 10.1039/c0sm01539c10.1039/c0sm01539c ↗
14. 10.1016/j.biotechadv.2011.06.01910.1016/j.biotechadv.2011.06.019 ↗
15. 10.1016/j.progpolymsci.2013.05.00610.1016/j.progpolymsci.2013.05.006 ↗
16. 10.1016/j.progpolymsci.2009.12.00310.1016/j.progpolymsci.2009.12.003 ↗
17. 10.1016/j.eurpolymj.2016.01.01610.1016/j.eurpolymj.2016.01.016 ↗
18. 10.1016/j.tca.2005.05.01110.1016/j.tca.2005.05.011 ↗
19. Babu RP, , O'Connor K, , Seeram R. Current progress on bio-based polymers and their future trends. Prog Biomater, 2013; 2(8):1–16; doi: 10.1186/2194-0517-2-8
20. 10.1016/j.polymdegradstab.2015.10.00110.1016/j.polymdegradstab.2015.10.001 ↗
21. 10.1016/j.compositesb.2014.11.02210.1016/j.compositesb.2014.11.022 ↗
22. 10.1016/j.compositesb.2011.11.06310.1016/j.compositesb.2011.11.063 ↗
23. 10.1002/app.1982.07027011210.1002/app.1982.070270112 ↗
24. 10.1016/j.matdes.2012.05.06010.1016/j.matdes.2012.05.060 ↗
25. 10.1063/1.32745810.1063/1.327458 ↗
26. 10.1021/acssuschemeng.9b0183010.1021/acssuschemeng.9b01830 ↗
27. Qiu TY, , Song M, , Zhao LG. Testing, characterization and modelling of mechanical behaviour of poly (lactic-acid) and poly (butylene succinate) blends. Mech Adv Mater Mod Proces, 2016; 2(7):1–11; doi: 10.1186/s40759-016-0014-9
28. 10.1002/app.1092310.1002/app.10923 ↗
29. 10.1002/(SICI)1099-0488(19990701)37:13<1357::AID-POLB2>3.0.CO;2-Q10.1002/(SICI)1099-0488(19990701)37:13<1357::AID-POLB2>3.0.CO;2-Q ↗
30. 10.1016/j.eurpolymj.2007.05.01310.1016/j.eurpolymj.2007.05.013 ↗
31. 10.1002/pen.2537810.1002/pen.25378 ↗
32. 10.1002/admt.20170017210.1002/admt.201700172 ↗
33. Bhatia A, , Gupta R, , Bhattacharya S, et al. Compatibility of biodegradable poly (lactic acid) (PLA) and poly (butylene succinate) (PBS) blends for packaging application. Korea Aust Rheol J, 2007; 19(3):125–131.
34. 10.1016/j.egypro.2013.06.77710.1016/j.egypro.2013.06.777 ↗
35. 10.1016/j.eurpolymj.2015.08.02910.1016/j.eurpolymj.2015.08.029 ↗
36. 10.1021/acsomega.8b0254910.1021/acsomega.8b02549 ↗
37. Zaldivar RJ, , Mclouth TD, , Ferrelli GL, et al. Effect of initial filament moisture content on the microstructure and mechanical performance of ULTEM® 9085 3D printed parts. Addit Manuf, 2018; 24:457–466; doi: 10.1016/j.addma.2018.10.022
38. 10.1016/j.jmatprotec.2009.05.01610.1016/j.jmatprotec.2009.05.016 ↗