journal article·2022-01

Tribological properties of PTFE/PPS films deposited on the ultrasonic rolling textured substrates by electrohydrodynamic atomization under dry reciprocating sliding

Jiaxing Wu, Jianxin Deng, Ying Meng, Shijie Wang, Ran Wang, Xuemu Li, Wei Sun

Wear· Volume 488-489
Publisher page

Abstract

Abstract The combination of texturing pretreatments and lubricant films was researched to improve the dry friction and wear performance of aluminium alloys. Three linear microtextures with different spacings were fabricated on the aluminum alloy substrates by ultrasonic surface rolling processing (USRP). The surface characteristics of different microtextures, such as micromorphologies, hardnesses, and wettability, were tested. PTFE/PPS lubricant films were prepared onto the textured surfaces by electrohydrodynamic atomization (EHDA), and micromorphologies of the films were observed. The friction and wear performance of aluminum alloy substrate and the films with texturing pretreatments were tested by ball-on disk reciprocating sliding dry friction experiments, and the countball material was 316L steel. The test data indicated that all films effectively reduced the friction coefficient of the substrate surface, and among them, the film sample URTC100 with a combination of 100 μm spacing texture and PTFE/PPS film exhibited the best effect of anti-wear while dry reciprocating sliding. Compared to the unpretreated film sample, URTC100 increased the wear life by 10% and reduced the wear track width and adhesion width by 35% and 25%, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electrohydrodynamics and Fluid Dynamics · Tribology and Lubrication Engineering · Lubricants and Their Additives

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Ceramic coating formation on high Si containing Al alloy by PEO process10.1179/1743294415Y.0000000003 ↗
2. The influence of sodium tungstate concentration and anodizing conditions on microarc oxidation (MAO) coatings for aluminum alloy10.1016/j.surfcoat.2012.02.002 ↗
3. Friction behavior of PTFE-coated Si3N4/TiC ceramics fabricated by spray technique under dry friction10.1016/j.ceramint.2020.10.255 ↗
4. Design of "double layer" texture to obtain superhydrophobic and high wear-resistant PTFE coatings on the surface of Al2O3/Ni layered ceramics10.1016/j.triboint.2019.04.004 ↗
5. Fabrication and tribological behaviors of a novel environmental friendly water-based PAI-PTFE-LaF3 bonded solid lubricating composite coating10.1016/j.triboint.2018.01.068 ↗
6. A novel structured suspension plasma sprayed YSZ-PTFE composite coating with tribological performance improvement10.1016/j.surfcoat.2018.11.021 ↗
7. Performance properties and applications of polytetrafluoroethylene (PTFE)-a review10.1007/s42114-018-0023-8 ↗
8. Wear resistant PTFE thin film enabled by a polydopamine adhesive layer10.1016/j.apsusc.2013.11.143 ↗
9. Tribological properties of superamphiphobic PPS/PTFE composite coating in the oilfield produced water10.1016/j.wear.2014.07.012 ↗
10. Extreme friction reductions during initial running-in of W-S-C-Ti low-friction coatings10.1016/j.wear.2013.01.065 ↗
11. Layer-modulated synthesis of uniform tungsten disulfide nanosheet using gas-phase precursors10.1039/C4NR04292A ↗
12. Wear-resistant coatings with engineered structure by laser cladding10.1007/s11249-004-8076-y ↗
13. Tribological properties of WS2 coatings deposited on textured surfaces by electrohydrodynamic atomization10.1016/j.surfcoat.2018.08.011 ↗
14. The electrical discharge from liquid points, and a hydrostatic method of measuring the electric intensity at their surfaces10.1103/PhysRev.3.69 ↗
15. Novel preparation of nitrogen-doped titanium dioxide films10.1088/0022-3727/41/21/215406 ↗
16. Classification of the modes of EHD spraying10.1016/S0021-8502(98)00787-3 ↗
17. Preparation and tribological properties of MoS2-based multiple-layer structured films fabricated by electrohydrodynamic jet deposition10.1016/j.surfcoat.2020.125334 ↗
18. Electrostatic spraying OF liquids - main functioning modes10.1016/0304-3886(90)90025-Q ↗
19. Effect of surface textures and electrohydrodynamically atomized WS2 films on the friction and wear properties of ZrO2 coatings10.1016/j.ceramint.2018.09.281 ↗
20. Testing piston rings with partial laser surface texturing for friction reduction10.1016/j.wear.2006.01.031 ↗
21. An analytical approach for analysis and optimisation of slider bearings with infinite width parallel textures10.1016/j.triboint.2010.02.016 ↗
22. Fabrication and tribological properties of Al2O3/TiC ceramic with nano-textures and WS2/Zr soft-coatings10.1016/j.surfcoat.2014.08.014 ↗
23. Tribological performance of AlCrN-MoS2/PTFE hard-lubricant composite coatings
24. Fabrication of honeycomb texture on poly-Si by laser interference and chemical etching10.1016/j.apsusc.2013.07.134 ↗
25. Fabrication of micro-textured surfaces using ball-end micromilling for wettability enhancement of Ti-6Al-4V10.1016/j.jmatprotec.2018.06.035 ↗
26. Tribological behavior of ZrO2/WS2 coating surfaces with biomimetic shark-skin structure10.1016/j.ceramint.2019.07.177 ↗
27. Laser surface texturing of a WC-CoNi cemented carbide grade: surface topography design for honing application10.1016/j.triboint.2018.02.018 ↗
28. Tribological properties of textured surfaces fabricated on AISI 1045 steels by ultrasonic surface rolling under dry reciprocating sliding
29. Effects of the different frequencies and loads of ultrasonic surface rolling on surface mechanical properties and fretting wear resistance of HIP Ti-6Al-4V alloy10.1016/j.apsusc.2016.07.120 ↗
30. The electrohydrodynamic atomization OF liquids10.1109/TIA.1986.4504754 ↗
31. Fabrication of AlTiN coatings deposited on the ultrasonic rolling textured substrates for improving coatings adhesion strength10.1016/j.apsusc.2021.149394 ↗
32. Nano mechanical properties of 40Cr surface layer after ultrasonic surface rolling processing
33. Numerical simulation of fracture behavior of in-situ TiB2 particle reinforced 2024-T4 aluminum matrix composites
34. Surface integrity enhancement of austenitic stainless steel treated by ultrasonic burnishing with two burnishing tips10.1007/s43452-020-00074-6 ↗
35. The influence of grain size determination method on grain growth kinetics analysis10.1002/adem.201500057 ↗
36. The Hall-Petch and inverse Hall-Petch relations and the hardness of nanocrystalline metals10.1007/s10853-019-04160-w ↗
37. Improving fatigue performance of Ti-6Al-4V alloy via ultrasonic surface rolling process10.1016/j.jmst.2019.03.036 ↗
38. The Scherrer equation and the dynamical theory of X-ray diffraction
39. Hall-Fetch relationship for austenitic stainless steels processed by large strain warm rolling10.1016/j.actamat.2017.06.060 ↗
40. Change of Young's modulus of cold-deformed pure iron in a tensile test10.1007/s11661-005-0006-6 ↗
41. Surface nanocrystallization of 17-4 precipitation-hardening stainless steel subjected to ultrasonic surface rolling process10.1016/j.msea.2018.04.033 ↗
42. Fabrication of WS2/C composite coatings via electrohydrodynamic atomization and their tribology behaviours10.1016/j.apsusc.2020.148128 ↗
43. Criteria for entrapped gas under a drop on an ultrahydrophobic surface10.1021/la801092y ↗
44. Resistance of solid surfaces to wetting by water10.1021/ie50320a024 ↗
45. Mechanism study on transition of cassie droplets to Wenzel state after meniscus touching substrate of pillars10.1021/acs.jpcc.6b12042 ↗
46. Synergistic effect of superhydrophobicity and oxidized layers on corrosion resistance of aluminum alloy surface textured by nanosecond laser treatment10.1021/acsami.5b06217 ↗
47. Deformation studies at sliding wear tracks IN iron10.1016/0043-1648(76)90018-1 ↗
48. Hardness measurements OF thin-films10.1016/0040-6090(84)90123-8 ↗