Design, development, and performance analysis of plate-plate hybrid magneto rheometer considering uniform radial magnetic flux
Source abstract
Abstract
The current study presents a magnetic numerical simulation of a plate-plate magnetorheometer using the finite-element method. In this study, a magnetorheometer with the least number of coil turns has been proposed and developed to obtain a high and consistent magnetic flux density (0.68 T at 3A) along the radius of the magnetorheological fluid (MRF) zone. The possibility of radial migration of MRF is eliminated by the lack of a magnetic flux gradient along the MRF zone’s radius. After comparing the temperature rise in the magnetorheometer caused by resistive and viscous heating in the simulation and the experiment, it has been found that the temperature rise has a negligible effect on the MR fluid. When we conducted studies in hybrid mode—that is, shear plus compression mode—we found that, under the same operating conditions, the shear stress was significantly higher compared to when we only used shear mode. In the combined shear plus compression mode, it has been observed that the effects of particle concentration and compression velocity have a significant impact on the shear stress value.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Vibration Control and Rheological Fluids · Fluid Dynamics and Vibration Analysis · Seismic Performance and Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Design of Parallel Plate Magnetorheometer for evaluating properties of Magnetorheological polishing fluid
2. de Vicente, Juan, Fernando Vereda, Juan Pablo Segovia-Gutiérrez, María del Puerto Morales, and Roque Hidalgo-Álvarez.,2010, “Effect of particle shape in magnetorheology,” J. Rheol. (N. Y. N. Y)., vol. 54, no. 6, pp. 1337–1362, 10.1122/1.3479045.10.1122/1.3479045 ↗
3. Gabriel, C., and H. M. Laun. “Combined slit and plate-plate magnetorheometry of a magnetorheological fluid (MRF) and parameterization using the Casson model,2009,” Rheol. Acta, vol. 48, no. 7, pp. 755–768, 10.1007/s00397-009-0369-5.10.1007/s00397-009-0369-5 ↗
4. Magnetorheological fluids: A review10.1039/c0sm01221a ↗
5. Characterization of commercial magnetorheological fluids at high shear rate: Influence of the gap
6. Structure of Electrorheological fluids
7. Structure and dynamics of electrorheological fluids10.1103/PhysRevE.57.756 ↗
8. Voelker-Pop, Loredana M. 2014, “Magneto-Rheological Device: TwinGapTM Geometry (MRD/TG),” vol. C74IA002EN, no. Fig. 1, pp. 1–5, [Online]. Available: https://www.antonpaar.com/?eID=documentsDownload&document=13030&L=0&dhash=afb01508e93dd7bf86bbfaa99c64168d.
9. Properties and Applications of Commercial Magnetorheological Fluids10.1177/1045389X9901000102 ↗
10. Magnetorheology: Applications and challenges10.1002/aic.690470202 ↗
11. “Drilling tests of an active vibration damper”, SPE/IADC Drill
12. Optimal magnetorheological damper configuration using the taguchi experimental design method10.1115/1.4024719 ↗
13. “A novel magnetorheological braking system with variable magnetic particle volume fraction controlled by utilizing shape memory alloy
14. Design, analysis and optimization of a hybrid fluid flow magnetorheological damper based on multiphysics coupling model
15. Principle design and control of a brake-by-wire actuator featuring magnetorheological clutch
16. Haosheng, Chen, Chen Darong, and Li Yongjian.’2006’, “Investigation on the effect of surface roughness pattern to drag force reduction using a rotary rheometer.” ASME Journal of Tribology., vol.128, pp. 131-138.10.1115/1.2125969.10.1115/1.2125969 ↗
17. Modeling of the non-linear rheological behavior of a lubricating grease at low-shear rates10.1115/1.555406 ↗
18. High pressure-short time shear strength analyzer for lubricants10.1115/1.3261024 ↗
19. The high shear stress rheology of liquid lubricants at pressures of 2 to 200 MPa10.1115/1.2920248 ↗
20. An analytical and computational investigation of high-rate rheometry10.1115/1.2831579 ↗
21. Double-gap plate–plate magnetorheology10.1122/1.5052247 ↗
22. Rheometry on magnetorheological (MR) fluids: I. Steady shear flow in stationary magnetic fields10.1007/BF00368993 ↗
23. Wall material and roughness effects on transmittable shear stresses of magnetorheological fluids in plate-plate magnetorheometry10.1007/s00397-011-0531-8 ↗
24. High-flux magnetorheology at elevated temperatures10.1007/s00397-013-0708-4 ↗
25. Magnetic and transient temperature field simulation of plate-plate magnetorheometer using finite-element method10.1109/TMAG.2019.2960237 ↗
26. Yazid, Izyan Iryani Mohd, Saiful Amri Mazlan, Takehito Kikuchi, Hairi Zamzuri, and Fitrian Imaduddin. 2013 “Design of magnetorheological damper with a combination of shear and squeeze modes.”Materials & Design (1980-2015)54 (2014): 87-95.10.1016/j.matdes.2013.07.090 ↗
27. 2013, “Theoretical and experimental studies on a magnetorheological brake operating under compression plus shear mode.”10.1088/0964-1726/22/11/115032 ↗
28. Book 1 electromagnetics fields
29. Ida, Nathan, and Joao PA Bastos. (1997) Electromagnetics and calculation of fields. 2nd Edition, Springer-Verlag Inc., New York. 10.1007/978-1-4612-0661-3.10.1007/978-1-4612-0661-3 ↗
30. A review of the slip (wall depletion) of polymer solutions, emulsions, and particle suspensions in viscometers: its cause, character, and cure10.1016/0377-0257(94)01282-M ↗
31. 2017, “Multi-objective design optimization and control of magnetorheological fluid brakes for automotive applications.”10.1088/1361-665X/aa9452 ↗
32. Influence of graphite flakes on the strength of magnetorheological fluids at high temperature and its rheology10.1109/TMAG.2020.2978159 ↗