Calculation Method for Torsional Angle of Main Cables of Suspension Bridges with Spatial Cables
Source abstract
Abstract
In suspension bridges employing spatial cables, the main cables undergo torsion during the construction process. Clarifying the distribution pattern of the main cable torsional angle can guide the positioning and installation of cable clamps and mitigate issues such as wire waving. This paper provides a theoretical calculation method for the distribution law of the torsion angle of the main cable. Firstly, it is assumed that the load form that causes the torsion of the main cable is the uniform load along the cable length and the span length. The theoretical calculation formulas of the torsion angle are derived, respectively, and the two formulas are compared. Analysis shows that under a uniformly distributed load, when the main cable is deflected at a certain angle, the torque is non-uniformly distributed along the cable, and the torsional angle follows a fourth-order parabolic curve along the span. A model test on spatial cable deflection was conducted, and the measured torsional angles were compared with theoretical results. The findings indicate that the measured torsional angle variation along the span is generally consistent with theoretical calculations. When the deflection angle of the spatial cable is large, the theoretical value exceeds the measured value. Furthermore, a finite element model was employed to calculate the torsional angle, torque, and bending moment during cable deflection. The results reveal that the distribution of the torsional angle depends on the ratio of the moment of inertia and the polar moment of inertia of the main cable section. The smaller the polar moment of inertia relative to the moment of inertia, the closer the torsional angle is to the spatial deflection angle. When the polar moment of inertia is relatively small, except in the end regions, the distribution of torque obtained from simulations is largely consistent with the theoretical values.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Structural Engineering and Vibration Analysis · Railway Engineering and Dynamics · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Architecture and Civil Engineering, Xi’an University of Science and Technology, No. 58 Yanta Rd., Xi’an 710054, China
Ankang Housing and Urban-Rural Housing Construction Bureau, Ankang 725000, China
Funding
National Natural Science Foundation of China · Natural Science Foundation of Shaanxi Province · Scientific Research Project of Ankang Housing and Urban-Rural Development Bureau
References (25)
Show source-provided references
1. Analysis of Stiffening Girder Hoisting Process of Suspension Bridge with Spatially-Configured Main Cables
2. Torsional calculation method of spatial cable with consideration of tension torsion coupling effect
3. Qi, D.C., and Wang, H.X. (2016). Model test of main cable torsion of spatial cable suspension bridge. Railw. Eng., 14–17. (In Chinese).
4. An overall bridge model test study on the mechanical behaviors in the process of system transfomation of self-anchored suspension bridge with spatial cable system
5. Test study on spatial cable torsion properties and torsion effect
6. Experimental on torsion performance of spatial main cables ofwire rope in suspension bridges
7. Experimental study on torsional behavior of spatial main cable for a self-anchored suspension bridge10.1177/1369433219857840 ↗
8. Numerical analysis of torsional property about spatial cable oftwin towers single span suspension bridge
9. A semi-analytical form-finding method of the 3D curved cable considering its flexural and torsional stiffnesses in suspension bridges10.1016/j.apm.2023.08.027 ↗
10. Tian, G., Zhang, W., and Chen, Y.P. (2025). Analytical assessment of suspension bridge’s 3D curved cable configuration and cable clamp pre-installation angle considering the main cable torsional and flexural stiffnesses. Appl. Math. Model., 138.10.1016/j.apm.2024.115805 ↗
11. Zhang, W., Lu, X., Wang, Z., and Liu, Z. (2021). Effect of the main cable bending stiffness on flexural and torsional vibrations of sus-pension bridges: Analytical approach. Eng. Struct., 240.10.1016/j.engstruct.2021.112393 ↗
12. Sun, Y., Liu, K., and Zhu, H.P. (2024). Nonlinear shape analysis for constructional multiwire cable structures with clamps considering multi-stiffness properties. Eng. Struct., 302.10.1016/j.engstruct.2023.117428 ↗
13. Experimental research on bending performance of structural cable10.1016/j.conbuildmat.2015.08.026 ↗
14. Nonlinear response of elastic cables with flexural-torsional stiffness10.1016/j.ijsolstr.2015.09.019 ↗
15. Static analysis and simplified design of suspension bridges having various rigidity of cables10.3846/jcem.2010.41 ↗
16. Finite element modelling for static behaviour analysis of suspension bridges with varying rigidity of main cables10.3846/1822-427X.2008.3.121-128 ↗
17. Ni, Y.Q., Ko, J.M., and Zheng, G. (1999, January 15–17). Free and forced vibration of large-diameter sagged cables taking into account bending stiffness. Proceedings of the Second International Conference on Advances in Steel Structures, Hong Kong, China.10.1016/B978-008043015-7/50060-9 ↗
18. Dynamic analysis of large-diameter sagged cables taking into account flexural rigidity10.1006/jsvi.2002.5060 ↗
19. Analytical investigation of the main cable bending stiffness effect on free flexural vibration of suspension bridges with a 3D cable system10.1016/j.istruc.2022.05.010 ↗
20. Bendalla, A.S.K., and Morgenthal, G. (2023). A nonlinear finite element framework for static and dynamic analysis of structural cables with deviating supports. Eng. Struct., 291.10.1016/j.engstruct.2023.116363 ↗
21. Theory and model implementation for analyzing line structures subject to dynamic motions of large deformation and elongation using the absolute nodal coordinate formulation (ANCF) approach10.1007/s11071-020-05783-4 ↗
22. Wang, D., Zhu, H., Xu, W., Ye, J., Zhang, D., and Wahab, M.A. (2022). Contact and slip behaviors of main cable of the long-span suspension bridge. Eng. Fail. Anal., 136.10.1016/j.engfailanal.2022.106232 ↗
23. Wang, L., Shen, R., Wang, T., Bai, L., Zhou, N., and Gu, S. (2024). A methodology for nonuniform slip analysis and evaluation of cable strands within saddle. Eng. Struct., 303.10.1016/j.engstruct.2024.117551 ↗
24. Geometrically exact finite element formulations for slender beams: Kirchhoff-Love theory versus Simo-Reissner theory10.1007/s11831-017-9232-5 ↗
25. Liu, Y., Song, K., and Meng, L. (2022). A geometrically exact discrete elastic rod model based on improved discrete curvature. Comput. Methods Appl. Mech. Eng., 392.10.1016/j.cma.2022.114640 ↗