journal article·2020-03-01

Study on the rolling friction and wear properties of surface densified powder metallurgy Fe-2Cu-0.6C material

Xiao Liu, Ya-hui Zheng, Yongliang Guo, Huijun Kong

Publisher page

Abstract

Abstract Rolling friction and wear behaviours of a surface densified Fe-2Cu-0.6C powder metallurgy material were investigated. Results indicated that friction coefficient and wear were significantly decreased after rolling. Wear rate tended to be steady as the rolling cycle increases. Under light load, wear was caused by delamination and ploughing. Delamination crack initiated on material surface. Under heavy load, wear was caused by delamination and pits. Cracks initiated at the surface and subsurface. However, due to the hardened surface layer and a lower porosity, probability of subsurface crack initiation was reduced and crack locations were closer to surface. Crack propagation distance also was shortened. The surface densified layer plays an important role in improving the rolling wear resistance of the material.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Experimental investigation into the surface integrity and tribological property of AISI 1045 steel specimen for barrel finishing10.1016/j.procir.2018.05.021 ↗
2. Rolling contact and adhesive wear of bainitic and pearlitic steels in low load regime10.1016/j.wear.2010.10.009 ↗
3. Experimental investigation on the effect of shot peening on contact fatigue strength for carburized and quenched gears10.1016/j.ijfatigue.2017.09.015 ↗
4. Rohith · 2018 · vol 14 · 1983
5. Effect of surface densification on the microstructure and mechanical properties of powder metallurgical gear by using a surface rolling process10.3390/ma9100846 ↗
6. Angelopoulos · 2017
7. Angelopoulos · 2018 · vol 14 · 1867
8. Lawcock · 2007 · vol 12 · 1
9. Improved PM Gear Rolling simulations using advanced material modelling10.1299/jamdsm.2017jamdsm0078 ↗
10. Effect of surface rolling on load bearing capacity of pre-alloyed sintered steel gears with different densities10.1016/j.proeng.2014.10.002 ↗
11. Bending fatigue, impact and pitting resistance of ausform-finished P/M gears
12. Surface Densification——an effective way to improve the performance of sintered gears10.3321/j.issn:1001-3784.2005.01.013 ↗
13. Harris · 2006 · 10610.1201/9781420006582 ↗
14. Flodin · 2004 · vol 2 · 395
15. Koide · 2017 · 313
16. Rolling contact fatigue of surface densified PM gears
17. Effect of lubricant viscosity and surface roughness on coefficient of friction in rolling contact
18. Effects of surface roughness on rolling10.1088/0143-0807/36/6/065029 ↗
19. Poisson’s ratio of sintered materials for structural machine parts10.2497/jjspm.51.515 ↗
20. Adhesion and friction between a smooth elastic spherical asperity and a plane surface10.1098/rspa.1997.0010 ↗
21. The effect of axle load and speed om rolling wear and damage behaviors of wheel/rail materials
22. Wear of nano-structured carbide-free bainitic steels under dry rolling-sliding conditions10.1016/j.wear.2012.11.064 ↗
23. Fatigue behavior of diffusion bonded powder metallurgy steel with heterogeneous microstructure10.1016/j.matdes.2008.06.050 ↗
24. Study of damage mechanisms and failure analysis of sintered and hardened steels under rolling–sliding contact conditions10.1016/j.msea.2006.09.039 ↗
25. Rolling contact fatigue and wear of CrL and CrM mode powder metallurgy steel
26. Fatigue crack growth from small to long cracks in VHCF with surface initiations10.1016/j.ijfatigue.2007.03.015 ↗
27. Propensities of crack interior initiation and early growth for very-high-cycle fatigue of high strength steels10.1016/j.ijfatigue.2013.02.023 ↗