Effect of multiaxial deformation on structure, mechanical properties, and corrosion resistance of a Mg-Ca alloy
Source abstract
Abstract
This article provides a report on the effect of multiaxial deformation (MAD) on the structure, texture, mechanical characteristics, and corrosion resistance of the Mg-0.8 (wt.)% Ca alloy. MAD was carried out on the alloy in the as-cast and the annealed states in multiple passes, with a stepwise decrease in the deformation temperature from 450 to 250 °C in 50 °C steps. The cumulative true strain at the end of the process was 22.5. In the case of the as-cast alloy, this resulted in a refined microstructure characterized by an average grain size of 2.7 µm and a fraction of high-angle boundaries (HABs) of 57.6%. The corresponding values for the annealed alloy were 2.1 µm and 68.2%. The predominant mechanism of structure formation was associated with discontinuous and continuous dynamic recrystallization acting in concert. MAD was also shown to lead to the formation of a rather sharp prismatic texture in the as-cast alloy, whilst in the case of the annealed one the texture was weakened. A displacement of the basal poles {00.4} from the periphery to the center of a pole figure was observed. These changes in the microstructure and texture gave rise to a significant improvement of the mechanical characteristics of the alloy. This included an increase of the ultimate tensile strength reaching 308 MPa for annealed material and 264 MPa for the as-cast one in conjunction with a twofold increase in ductility. A further important result of the MAD processing was a reduction of the rate of electrochemical corrosion, as indicated by a significant decrease in the corrosion current density in both microstructural states of the alloy studied.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Metal and Thin Film Mechanics · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Magnesium: properties-applications-potential10.1016/S0921-5093(00)01351-4 ↗
2. Magnesium alloys containing rare earth metals: structure and properties
3. Biodegradable Mg and Mg alloys: Corrosion and biocompatibility10.1016/j.mseb.2011.05.028 ↗
4. Biodegradable magnesium alloys for orthopaedic applications: a review on corrosion, biocompatibility and surface modifications10.1016/j.msec.2016.06.020 ↗
5. Biodegradable stents: they do their job and disappear
6. Biodegradable materials for bone repairs: a review10.1016/j.jmst.2013.03.002 ↗
7. Biodegradable metals10.1016/j.mser.2014.01.001 ↗
8. Recent advances on the development of magnesium alloys for biodegradable implants: review10.1016/j.actbio.2014.07.005 ↗
9. Bone-implant interface strength and osseointegration: Biodegradable magnesium alloy versus standard titanium control10.1016/j.actbio.2010.08.020 ↗
10. Nanophasic biodegradation enhances the durability and biocompatibility of magnesium alloys for the next-generation vascular stents10.1039/c3nr02912c ↗
11. Study on the in vitro degradation behavior of pure Mg and WE43 in human bile for 60 days for future usage in biliary10.1016/j.matlet.2016.05.042 ↗
12. Evaluation of short-term effects of rare earth and other elements used in magnesium alloys on primary cells and cell lines10.1016/j.actbio.2009.09.024 ↗
13. Valiev · 2014
14. Evolution of microstructure and hardness in an AZ80 magnesium alloy processed by high-pressure torsion10.1016/j.jmrt.2015.11.006 ↗
15. Evolution of microstructure and hardness in AZ31 alloy processed by high pressure torsion
16. Superplastic behaviour of AZ91 magnesium alloy processed by high-pressure torsion10.1016/j.msea.2015.04.004 ↗
17. Improving hydrogen storage performance of AZ31 Mg alloy by equal channel angular pressing and additives10.1016/j.jallcom.2018.01.412 ↗
18. Characterization of precipitates in an Al-Zn-Mg alloy processed by ECAP and subsequent annealing10.1016/j.msea.2017.11.091 ↗
19. Thermal stability of bimodal microstructure in magnesium alloy AZ91 processed by ECAP10.1016/j.matchar.2015.07.009 ↗
20. Increasing strength and ductility of magnesium alloy WE43 by equal-channel angular pressing10.1016/j.msea.2017.12.026 ↗
21. Producing bulk ultrafine-grained materials by severe plastic deformation10.1007/s11837-006-0213-7 ↗
22. Structure and properties of an Mg–0.3% Ca magnesium alloy after multiaxial deformation and equal channel angular pressing10.1134/S003602951411007X ↗
23. Structure of magnesium alloy MA14 after multistep isothermal forging and subsequent isothermal rolling10.1134/S0031918X15080116 ↗
24. Microstructure and superior mechanical properties of a multi-axially forged WE magnesium alloy10.1016/j.jallcom.2016.09.198 ↗
25. Micro and macro texture evolution during multiaxial forging of a WE43 magnesium alloy10.1016/j.jallcom.2017.12.181 ↗
26. Biomedical magnesium alloys: a review of material properties, surface modifications and potential as a biodegradable orthopaedic implant
27. Wear resistance of an ultrafine-grained Cu-Zr alloy processed by equal-channel angular pressing10.1016/j.wear.2014.12.022 ↗
28. Wear properties of ECAP-processed ultrafine grained Al–Cu alloys10.1016/j.msea.2010.03.057 ↗
29. Improvement of mechanical and tribological properties of Cu–Cr–Zr alloy by high pressure torsion and aging10.1016/j.jallcom.2018.01.303 ↗
30. Microstructure and corrosion properties of ultrafine-grained interstitial free steel10.1016/j.msea.2005.11.081 ↗
31. Strength, corrosion resistance, and biocompatibility of ultrafine-grained Mg alloys after different modes of severe plastic deformation10.1088/1757-899X/194/1/012004 ↗
32. Ultrafine-grained low carbon steels by severe plastic deformation
33. Effect of carbon and phosphorus addition on the fatigue roperties of ultrafine-grained steels10.1016/j.scriptamat.2005.01.035 ↗
34. Fatigue properties of ultra-fine grained dual phase ferrite/martensite low carbon steel10.1016/j.ijfatigue.2007.10.011 ↗
35. Structural changes in metastable austenitic steel during equal channel angular pressing and subsequent cyclic deformation10.1016/j.msea.2018.03.018 ↗
36. Structure and properties of ultra-fine grain Cu–Cr–Zr alloy produced by equal-channel angular pressing10.1016/S1359-6454(01)00437-2 ↗
37. Influence of microalloying with zirconium on the structure and properties of Cu–Cr alloy after high pressure torsion10.1016/j.msea.2015.10.008 ↗
38. ODF restoration by orientation grid10.4028/www.scientific.net/MSF.495-497.301 ↗
39. Effect of texture on tensile properties of an ECAP-processed MA2-1 magnesium alloy10.4028/www.scientific.net/SSP.160.159 ↗
40. Assessing the corrosion of biodegradable magnesium implants: A critical review of current methodologies and their limitations10.1016/j.actbio.2011.11.014 ↗
41. In-vitro dissolution of magnesium–calcium binary alloys: clarifying the unique role of calcium additions in bioresorbable magnesium implant alloys10.1002/jbm.b.31687 ↗
42. The development of binary Mg-Ca alloys for use as biodegradable materials within bone10.1016/j.biomaterials.2007.12.021 ↗
43. Humphreys · 1996
44. Correlation of plastic deformation and dynamic recrystallization in magnesium alloy ZK6010.1016/S1359-6454(01)00020-9 ↗
45. B. Predel. Ca - Mg (Calcium - Magnesium). In: Predel B. (eds) B - Ba … Cu - Zr. Landolt-Börnstein - Group IV Physical Chemistry (Numerical Data and Functional Relationships in Science and Technology), vol 12B. Springer, Berlin, Heidelberg, 2012. (https://doi.org/10.1007/978-3-540-44756-6_114).10.1007/978-3-540-44756-6_114 ↗
46. The double-edge effect of particles on the recrystallization behaviour and associated mechanical properties of metallic materials10.1016/j.pmatsci.2017.10.004 ↗
47. Introduction to grains, phases, and interfaces: an interpretation of microstructure
48. Corrosion of Pure Mg as a Function of Grain Size and Processing Route10.1002/adem.200800046 ↗
49. Grain character influences on corrosion of ECAPed pure magnesium10.1179/147842209X12559428167805 ↗
50. Enhanced corrosion resistance of Mg alloy ZK60 after processing by integrated extrusion and equal channel angular pressing10.1016/j.actamat.2011.06.033 ↗
51. Corrosion behavior of equal-channel-angular-pressed pure magnesium in NaCl aqueous solution10.1016/j.corsci.2009.10.004 ↗
52. The relation between severe plastic deformation microstructure and corrosion behavior of AZ31 magnesium alloy10.1016/j.jallcom.2008.01.084 ↗
53. Corrosion of pure Mg as a function of grain size and processing route10.1002/adem.200800046 ↗
54. Effect of grain size on corrosion: a review10.5006/1.3462912 ↗
55. Study of the degradation behavior and the biocompatibility of Mg–0.8Ca alloy for orthopedic implant application10.1016/j.jma.2019.02.007 ↗
56. In vitro and in vivo studies on pure Mg, Mg–1Ca and Mg–2Sr alloys processed by equal channel angular pressing10.1016/j.nanoms.2020.03.004 ↗
57. In vitro and in vivo studies on ultrafine-grained biodegradable pure Mg, Mg-Ca alloy and Mg-Sr alloy processed by high-pressure torsion10.1039/D0BM00805B ↗
58. In vitro corrosion of as-extruded Mg–Ca alloys — The influence of Ca concentration10.1016/j.corsci.2015.03.018 ↗
59. The development of binary Mg–Ca alloys for use as biodegradable materials within bone10.1016/j.biomaterials.2007.12.021 ↗
60. Enhancement of mechanical properties and corrosion resistance of Mg–Ca alloys through microstructural refinement by indirect extrusion10.1016/j.corsci.2014.01.041 ↗