Texture evolution induced by twinning and dynamic recrystallization in dilute Mg-1Sn-1Zn-1Al alloy during hot compression
Source abstract
Abstract
Texture evolution of an extruded dilute Mg-1Sn-1Zn-1Al alloy was thoroughly investigated based on the twinning and dynamic recrystallization (DRX) behavior via hot compression at a strain rate of 10 s−1 and temperature of 225°C. It was found that the types and intensities of the texture are strongly dependent on the fraction of twins and DRX modes as well as regions where sub-grain boundaries (sub-GBs) are intensively accumulated. At the initial stage of deformation, the formation of compression direction (CD)-tilted basal texture was mainly determined by the occurrence of {101¯2} extension twins. As the strain increases, the variation in the texture intensity was greatly dominated by the DRX modes but the type of main texture remained unchanged. These findings are of great importance for texture modification of wrought Mg-Sn-based alloys during post-deformation.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloy Microstructure Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Statistical optimization of stress level in Mg-Li-Al alloys upon hot compression testing10.1016/j.jma.2019.03.003 ↗
2. Effect of hot rolling on microstructure and properties of the ZEK100 alloy10.1016/j.jma.2019.02.001 ↗
3. Effects of group II elements on the cold stretch formability of Mg–Zn alloys10.1016/j.actamat.2014.10.005 ↗
4. Microstructure and texture evolution in LZ91 magnesium alloy during cold rolling10.1016/j.jma.2017.12.002 ↗
5. Investigation on the yield behavior of AZ91 magnesium alloy10.1016/j.jallcom.2017.12.160 ↗
6. Effect of Sn addition on the mechanical properties and bio-corrosion behavior of cytocompatible Mg–4Zn based alloys10.1016/j.jma.2019.02.002 ↗
7. Influence of basal slip activity in twin lamellae on mechanical behavior of Mg alloys10.1016/j.matlet.2016.04.113 ↗
8. Strengthening and toughening of magnesium alloy by {10−12} extension twins10.1016/j.scriptamat.2011.09.033 ↗
9. Twins, recrystallization and texture evolution of a Mg–5.99Zn–1.76Ca–0.35Mn (wt.%) alloy during indirect extrusion process10.1016/j.scriptamat.2011.07.053 ↗
10. Role of {10–12} twinning characteristics in the deformation behavior of a polycrystalline magnesium alloy10.1016/j.actamat.2010.07.002 ↗
11. Improving the mechanical properties of a hot-extruded AZ31 alloy by{10-12}twinning lamella10.1016/j.jallcom.2016.04.106 ↗
12. Texture Weakening Effects in Ce-Containing Mg Alloys10.1007/s11661-012-1486-9 ↗
13. Microstructure evolution and mechanical properties of quasicrystal-reinforced Mg–Zn–Gd alloy processed by cyclic extrusion and compression10.1016/j.jallcom.2014.11.167 ↗
14. An investigation to the hot deformation characteristics of AZ31 alloy through continuous cooling compression testing method10.1016/j.matdes.2011.10.050 ↗
15. Dynamic recrystallization behavior and hot workability of Mg–2.0Zn–0.3Zr–0.9Y alloy by using hot compression test10.1016/j.matdes.2013.07.016 ↗
16. Solute clustering and grain boundary segregation in extruded dilute Mg–Gd alloys10.1016/j.scriptamat.2014.08.022 ↗
17. Evolution of microstructure and microtexture during the hot deformation of Mg–3% Al10.1016/j.actamat.2010.04.017 ↗
18. Texture selection mechanisms in uniaxially extruded magnesium alloys10.1016/j.scriptamat.2010.01.018 ↗
19. Twinning, recrystallization and texture development during multi-directional impact forging in an AZ61 Mg alloy10.1016/j.jallcom.2015.07.281 ↗
20. Twinning-related microstructural evolution during hot rolling and subsequent annealing of pure magnesium10.1016/j.msea.2009.03.015 ↗
21. Effect of Sn addition on the microstructure and deformation behavior of Mg-3Al alloy10.1016/j.actamat.2016.11.020 ↗
22. A good balance between ductility and stretch formability of dilute Mg-Sn-Y sheet at room temperature10.1016/j.msea.2018.09.011 ↗
23. Effects of Sn addition on dynamic recrystallization of Mg-5Zn-1Mn alloy during high strain rate deformation10.1016/j.msea.2018.08.001 ↗
24. Improvement of mechanical properties and reduction of yield asymmetry of extruded Mg-Al-Zn alloy through Sn addition10.1016/j.jallcom.2018.07.028 ↗
25. Effect of Sn on the microstructure evolution of AZ80 magnesium alloy during hot compression10.1016/j.jallcom.2017.07.225 ↗
26. Hot deformation behavior and workability characteristic of a fine-grained Mg‒8Sn‒2Zn‒2Al alloy with processing map10.1016/j.jmst.2018.12.001 ↗
27. Effects of Zn and Ca addition on microstructure and mechanical properties of as-extruded Mg-1.0Sn alloy sheet10.1016/j.msea.2019.01.028 ↗
28. In-situ TEM observation of {10-12} twin-dominated deformation of Mg pillars: Twinning mechanism, size effects and rate dependency10.1016/j.actamat.2018.07.027 ↗
29. Tensile Properties and Corrosion Behavior of Extruded Low-Alloyed Mg-1Sn-1Al-1Zn Alloy: The Influence of Microstructural Characteristics10.3390/ma11071157 ↗
30. Twinning behavior of hot extruded AZ31 hexagonal prisms during uniaxial compression10.1016/j.jma.2018.12.004 ↗
31. Texture evolution of rolled Mg–3Al–1Zn alloy undergoing a {10-12} twinning dominant strain path change10.1016/j.jallcom.2015.05.194 ↗
32. In-plane anisotropic deformation behavior of rolled Mg–3Al–1Zn alloy by initial {10–12} twins10.1016/j.msea.2013.01.071 ↗
33. Influence of {10-12} extension twinning on the flow behavior of AZ31 Mg alloy10.1016/j.msea.2006.09.069 ↗
34. Hot deformation of the extruded Mg–10Li–1Zn alloy: Constitutive analysis and processing maps10.1016/j.jallcom.2016.12.087 ↗
35. Softening and dynamic recrystallization in magnesium single crystals during c-axis compression10.1016/j.actamat.2011.10.013 ↗
36. Microstructural evolution during large strain hot rolling of an AM60 Mg alloy10.1016/j.scriptamat.2003.11.014 ↗
37. Microstructure, texture and mechanical properties in an as-cast AZ61 Mg alloy during multi-directional impact forging and subsequent heat treatment10.1016/j.matdes.2015.08.052 ↗
38. Texture evolution during cold rolling of dilute Mg alloys10.1016/j.scriptamat.2015.06.009 ↗
39. Microstructures and textures of pure magnesium deformed in plane-strain compression10.1016/j.scriptamat.2004.07.002 ↗
40. The influence of a secondary twin on the detwinning deformation of a primary twin in Mg–3Al–1Zn alloy10.1016/j.msea.2014.03.068 ↗
41. Activation mode dependent {10−12} twinning characteristics in a polycrystalline magnesium alloy10.1016/j.scriptamat.2009.10.027 ↗
42. Tension–compression yield asymmetry in as-cast magnesium alloy10.1016/j.jallcom.2014.07.164 ↗
43. Hot deformation characteristics and processing map analysis of a new designed nickel-based alloy for 700°C A-USC power plant10.1016/j.jallcom.2015.09.219 ↗
44. EBSD study of a hot deformed nickel-based superalloy10.1016/j.jallcom.2015.04.008 ↗
45. Optimum parameters and kinetic analysis for hot working of a homogenized Mg–8Sn–1Al–1Zn alloy10.1016/j.matdes.2015.07.047 ↗
46. Necklace formation during dynamic recrystallization: mechanisms and impact on flow behavior10.1016/S1359-6454(97)00233-4 ↗
47. Role of starting texture and deformation modes on low-temperature shear formability and shear localization of Mg–3Al–1Zn alloy10.1016/j.actamat.2014.12.006 ↗
48. Correlation of plastic deformation and dynamic recrystallization in magnesium alloy ZK6010.1016/S1359-6454(01)00020-9 ↗
49. An investigation of dynamic recrystallization behavior of ZK60-Er magnesium alloy10.1016/j.msea.2014.06.058 ↗
50. Dynamic recrystallization during high temperature deformation of magnesium10.1016/j.msea.2008.02.004 ↗
51. Effect of extrusion temperature on texture evolution and recrystallization in extruded Mg–1% Mn and Mg–1% Mn–1.6%Sr alloys10.1016/j.jallcom.2012.12.078 ↗