journal article·2023-02-01Open access

Setup for electrical resistance measurement for laser material deposition with coaxial wire feed and use for process control

Max Fabian Steiner, Philipp Holger Lohrer, Thomas Schopphoven, Constantin Leon Häfner

Journal of Laser Applications· Volume 35· Issue 1

Abstract

Within laser additive manufacturing (directed energy deposition with laser beam), processes are further distinguished by the form of the filler material. In terms of availability, storage, safety, and cost, wire is commonly the preferred filler material in comparison to powder. Despite these advantages, due to the different material transfer modes, a greater process control is required. Within this work, an experimental setup for electrical-resistance-measurement within the laser material deposition process with a coaxial wire feed and its possible use for an automated process control is investigated. The measurement is performed between a wire, a substrate, and over the melt pool. One main influencing factor on process stability is derived from the timing of the trigger sequence of the laser power, process feed, and wire feed at the start and end points of every track. Consequently, inaccurate settings of the trigger sequence can, e.g., lead to deviations in track length and part geometry. Additionally, a smooth transfer of the wire into the melt pool is imperative during part build-up to ensure a stable deposition process. Variation in laser power, wire feed, process feed, or wire transfer mode can lead to process instabilities. This can result in imperfections, bonding defects, or pores in the tracks and layers that will add up in built components and must be avoided for defectfree three-dimensional geometries. Within the experiments, it is investigated whether the resistance-measurement provides consistent results under varying conditions and potentially can be utilized to automate the trigger sequence of deposition. Furthermore, it is investigated whether different wire transfer modes can be linked to the measured resistance values during welding of single tracks.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Fraunhofer Institute for Laser Technology ILT 1 , Steinbachstraße 15, Aachen 52074 Germany

Chair for Laser Technology LLT, RWTH Aachen University, 2 Steinbachstraße 15, Aachen 52074, Germany

References (18)

Show source-provided references
1. 2016
2. Wire-based laser metal deposition for additive manufacturing of TiAl6V4: Basic investigations of microstructure and mechanical properties from build up parts10.1117/12.2251336 ↗
3. Equipment and process windows for laser metal deposition with coaxial wire feeding10.2351/1.5096112 ↗
4. N. Klingbeil, “Untersuchung des Drahtsystems zur Prozessstabilisierung für das drahtbasierte Laserauftragsschweißen in der additiven Fertigung,” Ph.D. dissertation, RWTH Aachen, 2019.
5. Koaxiale Laserstrahlformung für die Lasermaterialbearbeitung mit Zusatzwerkstoff
6. Influence of focal length on the laser metal deposition process with coaxial wire feeding
7. A parametric study of Inconel 625 wire laser deposition10.1016/j.jmatprotec.2013.06.007 ↗
8. High-speed imaging and process characterization of coaxial laser metal wire deposition10.1016/j.addma.2018.05.043 ↗
9. Annular laser beam based direct metal deposition10.1016/j.procir.2018.08.099 ↗
10. Optical in-process height measurement system for process control of laser metal-wire deposition10.1016/j.precisioneng.2019.11.007 ↗
11. Influence of tool path planning on process stability and deposition accuracy in laser material deposition with coaxial wire feed10.2351/7.0000483 ↗
12. Resistance based iterative learning control of additive manufacturing with wire10.1016/j.mechatronics.2015.03.008 ↗
13. Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing10.1016/j.matdes.2016.01.099 ↗
14. Increased stability in laser metal wire deposition through feedback from optical measurements10.1016/j.optlaseng.2009.08.012 ↗
15. Correlations of melt pool geometry and process parameters during laser metal deposition by coaxial process monitoring10.1016/j.phpro.2014.08.167 ↗
16. Review on thermal analysis in laser-based additive manufacturing10.1016/j.optlastec.2018.04.034 ↗
17. Height control of laser metal-wire deposition based on iterative learning control and 3D scanning10.1016/j.optlaseng.2012.03.016 ↗
18. Resistance measurements for control of laser metal wire deposition10.1016/j.optlaseng.2013.10.010 ↗