The Role of MAX Phase Volume Fraction in Oxide Tribofilm Formation and Wear Mechanism of Cu–Ti3SiC2 and Cu–Ti3AlC2 Composites
Source abstract
Abstract
Abstract The paper presents a comparative analysis of the tribological behavior of copper-based composite materials with different contents (30 and 50 vol %) of the MAX phases Ti3SiC2 and Ti3AlC2, obtained by extrusion additive manufacturing. The samples were manufactured using a multi-stage technology: powder mixing, extrusion, additive formation, decomposition of the polymer binder, and heat treatment. Tribological tests were conducted under dry sliding friction conditions using the pin-on-disk scheme with a counterbody made of AISI 52 100 steel. The wear surfaces were examined using laser confocal and scanning electron microscopy with elemental mapping. Composites with 30 vol % MAX-phase (Cu–30%Ti3SiC2, coefficient of friction (COF) = 0.46; Cu–30%Ti3AlC2, COF = 0.51) demonstrate significantly higher values of the average friction coefficient in composite – AISI 52100 steel tribosystem compared to the samples containing 50 vol % MAX-phase (Cu–50%Ti3SiC2, COF = 0.28; Cu–50%Ti3AlC2, COF = 0.27). An oxide layer formed by oxides of the composite components was detected on the wear surfaces of all samples. The wear mechanism is defined as combined oxidative and adhesive, with similar wear particle morphology for all compositions. The tribological properties of composites are determined by both the volume fraction of the MAX phase and its chemical composition. The increased susceptibility of Ti3SiC2 to oxidation significantly influences the formation of the tribofilm and, consequently, the friction coefficient and wear resistance of the material.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: MXene and MAX Phase Materials · Advanced materials and composites · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. Makul, N., Modern sustainable cement and concrete composites: Review of current status, challenges and guidelines, Sustainable Mater. Technol., 2020, vol. 25, p. e00155. https://doi.org/10.1016/j.susmat.2020.e0015510.1016/j.susmat.2020.e00155 ↗
2. Suman, P., Kumar Bannaravuri, P., Baburao, G., Ratna Kandavalli, S., Alam, Sh., Shanthiraju, M., and Swamy Pulisheru, K., Integrity on properties of Cu-based composites with the addition of reinforcement: A review, Mater. Today Proc., 2021, vol. 47, pp. 6609–6613. https://doi.org/10.1016/j.matpr.2021.05.09610.1016/j.matpr.2021.05.096 ↗
3. Barsoum, M.W. and Radovic, M., Elastic and mechanical properties of the MAX phases, Annu. Rev. Mater. Res., 2011, vol. 41, no. 1, pp. 195–227. https://doi.org/10.1146/annurev-matsci-062910-10044810.1146/annurev-matsci-062910-100448 ↗
4. Ward, J., Bowden, D., Prestat, E., Holdsworth, S., Stewart, D., Barsoum, M.W., Preuss, M., and Frankel, P., Corrosion performance of Ti3SiC2, Ti3AlC2, Ti2AlC and Cr2AlC MAX phases in simulated primary water conditions, Corros. Sci., 2018, vol. 139, pp. 444–453. https://doi.org/10.1016/j.corsci.2018.04.03410.1016/j.corsci.2018.04.034 ↗
5. Firstov, S.A., Gorban’, V.F., Ivanova, I.I., and Pechkovskii, E.P., Mechanical properties of porous nanolaminate-composites Ti3SiC2/TiC, Ti3AlC2/TiC and Ti4AlN3/TiN in the temperature range of 20–1300°C, Poroshk. Metall., 2010, no. 7/8, pp. 56–68.10.1007/s11106-010-9252-2 ↗
6. Kachenyuk, M.N., Kulmetyeva, V.B., and Smetkin, A.A., Influence of nanosized titanium carbide on the synthesis, structure, and properties of a composite material based on titanium carbosilicide, Refract. Ind. Ceram., 2021, vol. 61, no. 5, pp. 587–591. https://doi.org/10.1007/s11148-021-00524-510.1007/s11148-021-00524-5 ↗
7. Dudina, D.V., Batraev, I.S., Ulianitsky, V.Yu., Korchagin, M.A., Golubkova, G.V., Abramov, S.Yu., and Lomovsky, O.I., Control of interfacial interaction during detonation spraying of Ti3SiC2–Cu composites, Inorg. Mater., 2014, vol. 50, no. 1, pp. 35–39. https://doi.org/10.1134/s002016851401003810.1134/s0020168514010038 ↗
8. Dang, W., Ren, Sh., Zhou, J., Yu, Yo., Li, Zh., and Wang, L., Influence of Cu on the mechanical and tribological properties of Ti3SiC2, Ceram. Int., 2016, vol. 42, no. 8, pp. 9972–9980. https://doi.org/10.1016/j.ceramint.2016.03.09910.1016/j.ceramint.2016.03.099 ↗
9. Sevostyanov, N.V., Burkovskaya, N.P., Bolsunovskaya, T.A., and Efimochkin, I.Yu., Influence of testing temperature on Ti3SiC2 titanium carbosilicide tribological properties, Trudy VIAM, 2019, no. 8, pp. 36–45. https://doi.org/10.18577/2307-6046-2019-0-8-36-4510.18577/2307-6046-2019-0-8-36-45 ↗
10. Beaman, J.J., Bourell, D.L., Seepersad, C.C., and Kovar, D., Additive manufacturing review: Early past to current practice, J. Manuf. Sci. Eng., 2020, vol. 142, no. 11, p. 110812. https://doi.org/10.1115/1.404819310.1115/1.4048193 ↗
11. Wong, K.V. and Hernandez, A., A review of additive manufacturing, ISRN Mech. Eng., 2012, vol. 2012, p. 208760. https://doi.org/10.5402/2012/20876010.5402/2012/208760 ↗
12. Frazier, W.E., Metal additive manufacturing: A review, J. Mater. Eng. Perform., 2014, vol. 23, no. 6, pp. 1917–1928. https://doi.org/10.1007/s11665-014-0958-z10.1007/s11665-014-0958-z ↗
13. Alekhin, V.O., Effect of silicon content in copper on phase composition and structure of Cu–Ti3SiC2 composite material, Za nami budushchee. Vzglyad molodykh uchenykh na innovatsionnoe razvitie obshchestva (Behind Us the Future: Young Scientists’ Views on Innovative Development of Society), 2020, pp. 174–177.
14. Umerov, E.R., Latukhin, E.I., and Markov, Yu.M., Peculiarities of the SHS skeleton of Ti3AlC2 and its subsequent spontaneous infiltration by the Al melt, Sovremennye Materialy, Tekhnika i Tekhnologii, 2020, no. 5, pp. 106–114. https://doi.org/10.47581/2020/30.10.2020/SMTT/32.5.01810.47581/2020/30.10.2020/SMTT/32.5.018 ↗
15. Gao, Z.-S., Xue, J., Ouyang, C.-S., Luo, Y.-S., Ding, K., Guo, H.-S., and Yan, G., Investigation of the microstructure and tribological properties of laser cladding 5% Ti3SiC2 reinforced Co-based composite coatings under different loads over the wide temperature range, Results Eng., 2024, vol. 24, p. 103142. https://doi.org/10.1016/j.rineng.2024.10314210.1016/j.rineng.2024.103142 ↗