The Influence of Radiation Modification on the Wear Resistance of Cutters Made of VK-8 Carbide Material
Source abstract
Abstract
Abstract The effect of gamma irradiation on some physicomechanical and tribological properties of VK-8 cemented carbide was investigated. Samples were CNMG 120408-46 indexable cutting inserts (manufacturer Sandvik MKTS, Russia) intended for turning. They were subject to gamma irradiation at various doses from 20 to 200 kGy and in different gaseous environments (air and nitrogen). Irradiation was carried out on an industrial GUD-300M facility using 60Co sources. Tests showed that after irradiation, a decrease in the electrical resistivity of the samples was observed, confirming the hypothesis of microstructure ordering in the irradiated material. Hardness measurements before and after irradiation did not reveal significant changes. However, a significant increase in the wear resistance of the material during cutting of various steels was established, from 1.5 to 6 times, depending on the absorbed irradiation dose, the steel being machined, and the cutting parameters. It is suggested that there exists an “optimal” level of gamma irradiation, below and above which the effect of radiation modification decreases. Determining this level requires separate tests for each material studied. However, general trends of increased wear resistance have been established in this article.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Polymer Science and Applications · Pulsed Power Technology Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. Oniskiv, V.D., Stolbov, V.Yu., Makarevich, Yu.L., and Chunaev, V.Yu., Some results of research into the strength and radiation resistance of carbon–basalt composite materials, Polym. Sci., Ser. D, 2024, vol. 17, no. 3, pp. 725–729. https://doi.org/10.1134/s199542122470124710.1134/s1995421224701247 ↗
2. Woods, R. and Pikaev, A., Applied Radiation Chemistry: Radiation Processing, New York: Wiley, 1994.
3. Oniskiv, V., Stolbov, V., and Ibragimova, E., Effect of gamma irradiation on morphology and local elemental composition of basalt-based composite material, Journal of Digital Science, 2023, vol. 5, no. 2, pp. 8–18. https://doi.org/10.33847/2686-8296.5.2_210.33847/2686-8296.5.2_2 ↗
4. Timoshenko, Yu.A., Klopotov, A.A., and Ivanov, Yu.F., Change of structural-phase state of VK-8 alloy under the action of gamma-quantum flux, Izv. Vyssh. Uchebn. Zaved., Chern. Metall., 2001, no. 4, pp. 40–43.
5. Makarov, V.F., Pesin, M.V., and Nikitin, S.P., Sovremennyi rezhushchii instrument dlya tsifrovogo mashinostroeniya (Modern Cutting Tools for Digital Machine Building), Perm: Permskii Natsional’nyi Issledovatel’skii Politekhnicheskii Universitet, 2025.
6. Was, G.S., Fundamentals of Radiation Materials Science: Metals and Alloys, Berlin: Springer, 2007. https://doi.org/10.1007/978-3-540-49472-010.1007/978-3-540-49472-0 ↗
7. Obodovskii, I.M., Radiatsionnye tekhnologii. Primenenie v laboratornykh issledovaniyakh, materialovedenii i nanotekhnologiyakh (Radiation Technology: Applications in Laboratory Research, Materials Science and Nanotechnology), Moscow: Intellekt, 2015.
8. Keizo, M. and Song, C., Radiation Processing of Polymer Materials and Its Industrial Applications, Hoboken, NJ: Wiley, 2012.
9. Oniskiv, V.D., Sotin, A.V., Stolbov, V.Yu., Nikulin, S.V., and Yuzhakova, E.V., Biomechanical aspects of radiation sterilization of composite material carbon-FC for medicine, Rossiiskii Zhurnal Biomekhaniki, 2023, vol. 27, no. 4, pp. 212–219. https://doi.org/10.15593/RZhBiomeh/2023.4.1710.15593/RZhBiomeh/2023.4.17 ↗
10. Ershov, B.G., Radiation technologies: Their possibilities, state, and prospects of application, Herald Russ. Acad. Sci., 2013, vol. 83, no. 5, pp. 437–447. https://doi.org/10.1134/s101933161309005010.1134/s1019331613090050 ↗
11. Oskolkova, T.N. and Glezer, A.M., Surface hardening of hard tungsten-carbide alloys: A review, Steel Transl., 2017, vol. 47, no. 12, pp. 788–796. https://doi.org/10.3103/s096709121712009910.3103/s0967091217120099 ↗
12. Feynman, R.P., Leighton, R.B., and Sands, M., Feynman Lectures on Physics 9. Quantum Mechanics, Moscow: Mir, 1965, 2nd ed.10.1119/1.1972241 ↗
13. Chernov, I.P. and Mamontov, A.P., Ordering of crystal structure by ionizing radiation (effect of low doses of ionizing radiation), Izvestiya Tomskogo Politekhnicheskogo Universiteta, 2000, vol. 303, no. 1, pp. 74–80.
14. Vorob’ev, V.L., Bykov, P.V., Gil’mutdinov, F.Z., and Bayakin, V.Ya., Effect of N+ ion implantation on surface morphology, chemical composition and atomic structure of stainless steel and titanium alloy surface layers, 14-i Mezhdunarodnyi Ural’skii seminar Radiatsionnaya fizika metallov i splavov. Tezisy dokladov (14th International Ural Seminar Radiation Physics of Metals and Alloys: Abstracts), 2022, pp. 61–62.
15. Didyk, A.Yu., Wiśniewski, R., Wilczyńska-Kitowska, T., Mishinsky, G.V., and Semin, V.A., Synthesis of chemical elements under irradiation by braking gamma-rays of palladium in condensed gases, Radioelektronika. Nanosistemy. Informatsionnye Tekhnologii, 2019, vol. 11, no. 2, pp. 143–160. https://doi.org/10.17725/rensit.2019.11.14310.17725/rensit.2019.11.143 ↗