journal article·2025-10

Discrete-Element Model of Wear of Structural Elements of a Centrifugal Decanter for Improved Cleaning of Drilling Fluids

E. M. Dekanoidze, M. A. Skotnikova

Journal of Friction and Wear· Volume 46· Issue 5
Publisher page

Abstract

Abstract It is shown that during drilling, cleaning of drilling solution using centrifugal decanters minimizes the presence of abrasive particles in the system and reduces mechanical wear of structural elements and pumping units. The results of a comparative analysis of the resource of the initial nozzle design and three proposed modifications, differing in surface geometry and orientation relative to the direction of rotation of the drum, are presented. A comprehensive assessment of the effect of design changes on the particle escape velocity and, as a result, on the wear rate was carried out using an analytical model for calculating the amount of wear during particle impact. A discrete-element model of the processes accompanying the operation of a centrifugal decanter (movement of drilling solution along the centrifuge screw) has been developed. The time before the formation of critical wear (destruction) of the nozzle surfaces is calculated. The influence of geometric and design parameters of centrifugal decanter nozzles on the efficiency of the drilling solution cleaning process has been studied. It is shown that reducing the height and diameter of the nozzles to 34 and 37 mm, respectively, increased the surface wear time by 1.5 times. An analytical evaluation of the resource of cylindrical nozzle surfaces for various design options has been performed. A significant increase in service life is achieved by changing the inclination of the cylindrical surfaces of the nozzles against the direction of rotation of the drum. The wear time of the nozzle surface increases 12.5 times.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Mechanical Systems and Engineering · Advanced Theoretical and Applied Studies in Material Sciences and Geometry · Engineering Technology and Methodologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. Menesklou, P., Sinn, T., Nirschl, H., and Gleiss, M., Scale-up of decanter centrifuges for the particle separation and mechanical dewatering in the minerals processing industry by means of a numerical process model, Minerals, 2021, vol. 11, no. 2, p. 229. https://doi.org/10.3390/min1102022910.3390/min11020229 ↗
2. Bashkirtsev, V.I. and Yuditskii, L.A., Scientific understanding of adhesion, Servis v Rossii i za Rubezhom, 2012, no. 3, pp. 216–223.
3. Yudakov, V.S., Dekanoidze, E.M., Mukhtarov, M.Sh., and Tilichkan, A.A., Research of the influence of the zenith angle of an incluined directional well on the stress-strain state of the near-well space, Mezhdunarodnyi Nauchno-Issledovatel’skii Zhurnal, 2020, no. 8-1, pp. 157–162. https://doi.org/10.23670/IRJ.2020.98.8.02210.23670/IRJ.2020.98.8.022 ↗
4. Liu, Y.-J., Zhu, L.-N., Feng, M.-G., Da, Q., and Kang, J.-J., Study on the erosion wear characteristics and structural optimization of key components of drilling fluid centrifuge, J. Failure Anal. Prev., 2025, vol. 25, no. 1, pp. 468–486. https://doi.org/10.1007/s11668-025-02117-710.1007/s11668-025-02117-7 ↗
5. Li, K., Zhou, F., Fu, Sh., Zhang, Ya., Dai, Ch., Yuan, H., and Yu, Sh., Study on the separation performance of a decanter centrifuge used for dewatering coal water slurry, Chem. Eng. Res. Des., 2023, vol. 195, pp. 711–720. https://doi.org/10.1016/j.cherd.2023.06.01310.1016/j.cherd.2023.06.013 ↗
6. Liu, H., Li, P., Xiao, H., and Mu, W., The fluid–solid coupling analysis of screw conveyor in drilling fluid centrifuge based on ANSYS, Petroleum, 2015, vol. 1, no. 3, pp. 251–256. https://doi.org/10.1016/j.petlm.2015.07.00910.1016/j.petlm.2015.07.009 ↗
7. Yudakov, V.S. and Dekanoidze, E.M., Creation of an algorithm for performance of calculations of the stability of walls of inclined directional well using Mathcad, Aktual’nye Nauchnye Issledovaniya v Sovremennom Mire, 2020, no. 7-2, pp. 147–152.
8. Dekanoidze, E.M., Developing an algorithm and writing programs for performing calculations with MATLAB, Aktual’nye Nauchnye Issledovaniya v Sovremennom Mire, 2020, no. 7-1, pp. 50–53.
9. Bai, Ch., Park, H., and Wang, L., Modelling solid-liquid separation and particle size classification in decanter centrifuges, Sep. Purif. Technol., 2021, vol. 263, p. 118408. https://doi.org/10.1016/j.seppur.2021.11840810.1016/j.seppur.2021.118408 ↗
10. Zhu, M., Hu, D., Xu, Yu., and Zhao, Sh., Design and computational fluid dynamics analysis of a three-phase decanter centrifuge for oil-water-solid separation, Chem. Eng. Technol., 2020, vol. 43, no. 5, pp. 1005–1015. https://doi.org/10.1002/ceat.20190024510.1002/ceat.201900245 ↗
11. Gleiss, M., Hammerich, S., Kespe, M., and Nirschl, H., Application of the dynamic flow sheet simulation concept to the solid-liquid separation: Separation of stabilized slurries in continuous centrifuges, Chem. Eng. Sci., 2017, vol. 163, pp. 167–178. https://doi.org/10.1016/j.ces.2017.01.04610.1016/j.ces.2017.01.046 ↗
12. Leone, A., Romaniello, R., Zagaria, R., and Tamborrino, A., Mathematical modelling of the performance parameters of a new decanter centrifuge generation, J. Food Eng., 2015, vol. 166, pp. 10–20. https://doi.org/10.1016/j.jfoodeng.2015.05.01110.1016/j.jfoodeng.2015.05.011 ↗
13. Nepomnyashchii, E.F., Friction and wear under the influence of a jet of solid spherical particles, Kontaktnoe vzaimodeistvie tverdykh tel i raschet sil treniya i iznosa (Contact Interaction of Solids and Calculation of Friction and Wear Forces), Moscow: Nauka, 1971, pp. 190–200.
14. Tamarkin, M.A. and Tikhonov, A.A., Methods of calculating metal removal under hydroabrasive treatment, Vestnik Donskogo Gosudarstvennogo Tekhnicheskogo Universiteta, 2011, vol. 11, no. 3, pp. 327–332.