Mechanical Properties and Tribological Characteristics of Copper Matrix Composite Reinforced with TiC–Ti
Source abstract
Abstract
Abstract The paper studies the microstructure, phase composition, mechanical properties, and tribological characteristics of copper matrix composites of the Cu–Fe–FeCr–MoS2–C system reinforced with TiC–Ti composite inclusions sized 100–140 and 140–200 μm. The composites under study were obtained by sintering under pressure, and the content of reinforcing TiC–Ti inclusions was 3, 5, 7, 9, and 11 vol %. It is shown that the hardness of the composites under study increases with the addition of TiC–Ti metal-ceramic inclusions to 15 HBW 10/250/30, which is more than 40% higher than the hardness of the matrix composite. It is revealed that composites reinforced with TiC–Ti inclusions have greater wear resistance compared to the matrix composite without the introduction of reinforcing inclusions. It was found that the composite containing 7 vol % TiC–Ti inclusions 100–140 μm in size has the highest wear resistance, and an increase in the inclusion content to 9 and 11 vol % leads to an increase in the wear intensity of the composite. With the introduction of more than 7 vol % TiC–Ti composite inclusions 140–200 μm in size, a decrease in wear resistance also occurs. The maximum friction coefficient is demonstrated by the composite reinforced with 11 vol % TiC–Ti inclusions 100–140 μm in size, which is 0.36 ± 0.03, and with an increase in the inclusion size to 140–200 μm, the highest friction coefficient is observed with the introduction of 7 vol % TiC–Ti.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. Xiao, J.-K., Xiao, S.-X., Chen, J., and Zhang, Ch., Wear mechanism of Cu-based brake pad for high-speed train braking at speed of 380 km/h, Tribol. Int., 2020, vol. 150, p. 106357. https://doi.org/10.1016/j.triboint.2020.10635710.1016/j.triboint.2020.106357 ↗
2. Peng, T., Yan, Q., Li, G., Zhang, X., Wen, Z., and Jin, X., The braking behaviors of Cu-based metallic brake pad for high-speed train under different initial braking speed, Tribol. Lett., 2017, vol. 65, no. 4, pp. 135–148. https://doi.org/10.1007/s11249-017-0914-910.1007/s11249-017-0914-9 ↗
3. Bodrova, L.E., Meilakh, A.G., and Pastukhov, E.A., Dispersion hardening of copper with plated particles of chromium and niobium carbides, Fiz. Khim. Obrab. Mater., 2016, no. 1, pp. 68–75.
4. Fadin, V.V., Kolubaev, A.V., and Aleutdinova, M.I., Friction of composites based on titanium carbide produced by the process combustion method, J. Frict. Wear, 2011, vol. 32, no. 6, pp. 462–466. https://doi.org/10.3103/s106836661106005510.3103/s1068366611060055 ↗
5. Shuster, L.Sh., Mamleyev, R.F., Kamaletdinova, R.R., Chertovskikh, S.V., and Kireev, R.M., Wear of friction pairs made of titanium carbide-based metal–ceramic material, J. Frict. Wear, 2016, vol. 37, no. 2, pp. 165–169. https://doi.org/10.3103/s106836661602014810.3103/s1068366616020148 ↗
6. Eremenko, V.N., Buyanov, Yu.I., and Prima, S.B., Structure of the phase diagram of the titanium–copper system, Poroshk. Metall., 1966, no. 6, p. 77.10.1007/BF00775543 ↗
7. Shmakov, V.V., Buyakov, A.S., and Buyakova, S.P., Fractal analysis of surface topography evolution in homogeneous and dual ZrB2–TaB2–SiC composites during abrasive wear, Tech. Phys. Lett., 2024, vol. 50, no. 11, p. 63.10.1134/S1063785024700317 ↗
8. Fasihi, P., Kendall, O., Abrahams, R., Mutton, P., Lai, Q., Qiu, C., and Yan, W., Effect of graphite and MoS2 based solid lubricants for application at wheel–rail interface on the wear mechanism and surface morphology of hypereutectoid rails, Tribol. Int., 2021, vol. 157, p. 106886. https://doi.org/10.1016/j.triboint.2021.10688610.1016/j.triboint.2021.106886 ↗
9. Prabhu, T.R., Arivarasu, M., Chodancar, Ya., Arivazhagan, N., Sumanth, G., and Mishra, R.K., Tribological behaviour of graphite-reinforced FeNiCrCuMo high-entropy alloy self-lubricating composites for aircraft braking energy applications, Tribol. Lett., 2019, vol. 67, no. 3, pp. 78–93. https://doi.org/10.1007/s11249-019-1193-410.1007/s11249-019-1193-4 ↗
10. Dudina, D.V., Ukhina, A.V., Bokhonov, B.B., Korchagin, M.A., Bulina, N.V., and Kato, H., The influence of the formation of Fe3C on graphitization in a carbon-rich iron-amorphous carbon mixture processed by spark plasma sintering and annealing, Ceram. Int., 2017, vol. 43, no. 15, pp. 11902–11906. https://doi.org/10.1016/j.ceramint.2017.06.03810.1016/j.ceramint.2017.06.038 ↗
11. Xiao, Ye., Zhang, Zh., Yao, P., Fan, K., Zhou, H., Gong, T., Zhao, L., and Deng, M., Mechanical and tribological behaviors of copper metal matrix composites for brake pads used in high-speed trains, Tribol. Int., 2018, vol. 119, pp. 585–592. https://doi.org/10.1016/j.triboint.2017.11.03810.1016/j.triboint.2017.11.038 ↗
12. Bagheri, Gh.H.A., The effect of reinforcement percentages on properties of copper matrix composites reinforced with TiC particles, J. Alloys Compd., 2016, vol. 676, pp. 120–126. https://doi.org/10.1016/j.jallcom.2016.03.08510.1016/j.jallcom.2016.03.085 ↗