Friction and Wear of Composite Material Based on Al–Mg Alloy Modified by Iron Powder via Friction Stir Processing
Source abstract
Abstract
Abstract— This work is dedicated to the study of tribological behavior of composite materials obtained by friction stir processing (FSP) from AA5056 aluminum–magnesium alloy with addition of iron under dry sliding friction. For the tests, four different types of samples were obtained by FSP, differing in their iron powder content, namely 0, 5, 10, and 15 vol %. For each type of composite, four passes of FSP were performed to achieve a uniform distribution of the iron powder throughout the stir zone. Sliding tests were conducted using the pin-on-disc method against a counter-body made of stainless steel containing 12–14% chromium (AISI 420). Increasing the Fe powder content leads to a decrease in the average coefficient of friction by approximately 10–15%, as well as a reduction in wear by approximately 20%. The study of worn surfaces showed that with an increase in the amount of iron powder added during FSP, the wear mechanism changes from adhesive to abrasive. Homogeneous distribution of intermetallic compound (IMC) particles of Al6Fe and Al13Fe4 in-situ synthesized during FSP made it possible to increase the wear resistance of the composites compared to the base alloy without iron additives. A mechanically mixed layer consisting of a deformed matrix mixed with fragmented and oxidized IMCs was formed on the worn surfaces of all the studied composites and served as protection against adhesive wear and performed the function of a wear-resistant antifriction coating.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (9)
Show source-provided references
1. Abouei, V., Saghafian, H., Shabestari, S.G., and Zarghami, M., Effect of Fe-rich intermetallics on the wear behavior of eutectic Al–Si piston alloy (LM13), Mater. Des., 2010, vol. 31, no. 7, pp. 3518–3524. https://doi.org/10.1016/j.matdes.2010.02.01510.1016/j.matdes.2010.02.015 ↗
2. Canakcı, A., Ozkaya, S., Erdemir, F., Karabacak, A.H., and Celebi, M., Effects of Fe–Al intermetallic compounds on the wear and corrosion performances of AA2024/316L SS metal/metal composites, J. Alloys Compd., 2020, vol. 845, p. 156236. https://doi.org/10.1016/j.jallcom.2020.15623610.1016/j.jallcom.2020.156236 ↗
3. Sarkari Khorrami, M., Samadi, S., Janghorban, Z., and Movahedi, M., In-situ aluminum matrix composite produced by friction stir processing using FE particles, Mater. Sci. Eng., A, 2015, vol. 641, pp. 380–390. https://doi.org/10.1016/j.msea.2015.06.07110.1016/j.msea.2015.06.071 ↗
4. Lee, I.S., Kao, P.W., and Ho, N.J., Microstructure and mechanical properties of Al–Fe in situ nanocomposite produced by friction stir processing, Intermetallics, 2008, vol. 16, no. 9, pp. 1104–1108. https://doi.org/10.1016/j.intermet.2008.06.01710.1016/j.intermet.2008.06.017 ↗
5. Roy, D., Basu, B., Basu Mallick, A., Manoj Kumar, B.V., and Ghosh, S., Understanding the unlubricated friction and wear behavior of Fe-aluminide reinforced Al-based in-situ metal–matrix composite, Composites, Part A, 2006, vol. 37, no. 9, pp. 1464–1472. https://doi.org/10.1016/j.compositesa.2005.06.02210.1016/j.compositesa.2005.06.022 ↗
6. Knyazhev, E., Nikolaeva, A., Chumaevskii, A., Cheremnov, A., Zykova, A., Gurianov, D., Utyaganova, V., Moskvichev, E., Savchenko, N., and Tarasov, S., Iron-added aluminum matrix composites prepared by friction stir processing: Structure, mechanical and tribological properties, Metallogr., Microstruct., Anal., 2024, vol. 13, no. 3, pp. 376–399. https://doi.org/10.1007/s13632-024-01085-y10.1007/s13632-024-01085-y ↗
7. Zykova, A., Vorontsov, A., Chumaevskii, A., Gurianov, D., Savchenko, N., Gusarova, A., Kolubaev, E., and Tarasov, S., In situ intermetallics-reinforced composite prepared using multi-pass friction stir processing of copper powder on a Ti6Al4V alloy, Materials, 2022, vol. 15, no. 7, p. 2428. https://doi.org/10.3390/ma1507242810.3390/ma15072428 ↗
8. Wang, T., Gwalani, B., Shukla, Sh., Frank, M., and Mishra, R.S., Development of in situ composites via reactive friction stir processing of Ti–B4C system, Composites, Part B, 2019, vol. 172, pp. 54–60. https://doi.org/10.1016/j.compositesb.2019.05.06710.1016/j.compositesb.2019.05.067 ↗
9. Zhang, W., Ding, H., Cai, M., Yang, W., and Li, J., Ultra-grain refinement and enhanced low-temperature superplasticity in a friction stir-processed Ti–6Al–4V alloy, Mater. Sci. Eng., A, 2018, vol. 727, pp. 90–96. https://doi.org/10.1016/j.msea.2018.03.00910.1016/j.msea.2018.03.009 ↗