journal article·2024-06

Influence of Ultrafine Additives of Intermetallides on the Structure, Mechanical, and Tribotechnical Properties of Sintered Tin Bronze

L. N. Dyachkova, A. I. Letsko

Journal of Friction and Wear· Volume 45· Issue 3
Publisher page

Abstract

Abstract The results of a study of the influence of the introduction of powders of intermetallic compounds of various compositions obtained by self-propagating high-temperature synthesis (SHS) with preliminary mechanical activation on the structure, mechanical, and tribological properties of sintered bronze are presented. It was found that the introduction of 0.2–0.5 wt % of nickel and titanium aluminides, both single-phase and two-phase, leads to an increase in the density and strength of sintered bronze; maximum strength is achieved with the introduction of 0.2 wt % aluminides. The dependence of the hardness of powder bronze on the amount and composition of the intermetallic compound differs from the dependence of strength; with the introduction of single-phase intermetallic compounds, the hardness increases with increasing additive content, and with two-phase intermetallic compounds it decreases. It has been shown that the introduction of aluminides ensures a refinement of the structure of the bronze during sintering, and at an additive content of 1 wt %, an increase in the amount of eutectoid (α + δ). The introduction of aluminides also has a positive effect on the tribological properties of sintered bronze. With the introduction of 0.5 wt % two-phase nickel aluminide and 0.2 wt % single-phase titanium aluminide, the seizure pressure and wear resistance increase by 2.8 times and 3.5 times, respectively. Adding 0.5 wt % of single-phase nickel, titanium, and iron aluminides allows reducing the friction coefficient to 0.009–0.011, and two-phase iron aluminide to 0.005. The introduction of iron aluminides most effectively increases the tribological properties of sintered bronze, so the seizure pressure increases to 10 MPa and wear resistance by almost 10 times. Aluminides help reduce the relief of the friction surface during adhesive wear of sintered bronze and the formation of microlacunae, which are additional reservoirs for lubrication. The smoothest friction surface and a higher content of microlacunae are observed in samples made of powder bronze with the addition of single-phase iron aluminide.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · Powder Metallurgy Techniques and Materials · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. Bataev, A.A. and Bataev, V.A., Kompozitsionnye materialy. Stroenie, poluchenie, primenenie (Composite Materials: Structure, Preparation, Applications), Moscow: Universitetskaya Kniga; Logos, 2006.
2. Fedorchenko, I.M., Frantsevich, I.N., Radomysel’skii, I.D., et al., Poroshkovaya metallurgiya, materialy, tekhnologiya, svoistva, oblasti primeneniya (Powder Metallurgy, Materials, Technology, Properties, Applications), Kiev: Naukova Dumka, 1985.
3. Vityaz’, P.A., Zhornik, V.I., Kukareko, V.A., Komarov, A.I., and Senyut’, V.T., Modifitsirovanie materialov i pokrytii nanorazmernymi almazosoderzhashchimi dobavkami (Modification of Materials and Coatings by Nanoscale Diamond Containing Additives), Minsk: Belarusskaya Nauka, 2011.
4. Sadykov, F.A., Barykin, N.P., and Aslanyan, I.R., Wear of copper and its alloys with submicrocrystalline structure, Wear, 1999, vols. 225–229, pp. 649–655. https://doi.org/10.1016/s0043-1648(98)00374-310.1016/s0043-1648(98)00374-3 ↗
5. Marek, B., Kompozyt ceramika Al2O3-STOP Ni–Fe–Cr do taczenia ceramiki z metalami, Kompozyty, 2001, no. 1, pp. 12–15.10.62753/ctp.2001.03.1.1 ↗
6. Li, A.-M., Mechanical properties and microstructure of Fe–Al/Al2O3 composite with Cr, Mo, and Ti, Trans. Nonferrous Met. Soc. China, 2003, vol. 13, no. 4, pp. 860–863.
7. Tjong, S.C. and Lau, K.C., Sliding wear of stainless steel matrix composite reinforced with TiB2 particles, Mater. Lett., 1999, vol. 41, no. 4, pp. 153–158. https://doi.org/10.1016/s0167-577x(99)00123-810.1016/s0167-577x(99)00123-8 ↗
8. D’yachkova, L.N. and Talako, T.L., Investigation of the influence of additives of mechanically activated oxide powders on the structure and properties of iron-based powder material, Inzheneriya poverkhnosti. Novye poroshkovye kompozitsionnye materialy. Svarka: Materialy Mezhdunar. simpoziuma (Surface Engineering. New Powder Composite Materials. Welding: Proc. Int. Symp.), Minsk, 2009, vol. 2, pp. 65–70.
9. D’yachkova, L.N. and Letsko, I.N., Influence of disperse additives of chromium borides on structure and properties of powdered carbon steel, Poroshkovaya Metall., 2007, no. 30, pp. 67–70.
10. Karapetyan, G.Kh., Akopov, N.L., and Karapetyan, F.Kh., Wear-resistant powder materials with intermetallide hardening. I. Poreless materials for antifriction purposes, Poroshkovaya Metall., 1987, no. 4, pp. 75–79.10.1007/BF01184444 ↗
11. Korchagin, M.A., Grigor’eva, T.F., Barinova, A.P., and Lyakhov, N.Z., A regime of the solid-state reaction in the self-propagating high-temperature synthesis, Dokl. Phys., 2000, vol. 45, no. 5, pp. 205–207. https://doi.org/10.1134/1.17174310.1134/1.171743 ↗
12. Merzhanov, A.G., The chemistry of self-propagating high-temperature synthesis, J. Mater. Chem., 2004, vol. 14, no. 12, pp. 1779–1786. https://doi.org/10.1039/b401358c10.1039/b401358c ↗
13. Grigor’eva, T.F., Korchagin, M.A., Barinova, A.P., and Lyakhov, N.Z., Effect of mechanochemical activation on the concentration boundaries of self-propagating high-temperature synthesis, Dokl. Chem., 1999, vol. 369, nos. 1–3, pp. 285–287. https://www.elibrary.ru/lfhand.
14. Bernard, F. and Gaffet, E., Mechanical alloying in SHS research, Int. J. SHS, 2001, no. 2, pp. 109–131.
15. Grigor’eva, T.V., Baranova, A.P., and Lyakhov, N.Z., Mechanochemical synthesis of intermetallic compounds, Usp. khimii, 2001, no. 1, pp. 54–71.
16. Letsko, A.I., Il’yushchenko, A.F., Khina, B.B., Talako, T.L., and Belyaev, A.V., Features of mechanoactivation of reaction charge for synthesis of iron aluminides, Poroshkovaya Metall., 2005, no. 28, pp. 100–113.
17. Lyakoshev, N.P., Diagrammy sostoyaniya dvoinykh metallicheskikh sistem. Spravochnik. V 3-kh t. (State Diagrams of Binary Metallic Systems: Handbook in 3 Volumes), Moscow: Mashinostroenie, 1996.
18. Feldshtein, E.E. and Dyachkova, L.N., Wear minimization for highly loaded iron-based MMCs due to the formation of spongy-capillary texture on the friction surface, Wear, 2020, vols. 444–445, p. 203161. https://doi.org/10.1016/j.wear.2019.20316110.1016/j.wear.2019.203161 ↗