journal article·2022-04

Using Synthetic Alumina Based Fibers as a Friction Additive

N. V. Sevostyanov, V. G. Babashov, N. P. Burkovskaya, T. A. Bolsunovskaya

Journal of Friction and Wear· Volume 43· Issue 2
Publisher page

Abstract

This study proposes to use synthetic discrete refractory fiber, grade NDA-17-42-2, based on alumina and silica (in the weight ratio 85 and 15%, respectively) with a diameter from 1 to 3 μm as a friction component in tribotechnical materials. Due to high hygroscopy in combination with a high specific surface area up to 400 m2/g (comparable to asbestos) it is possible to expect high efficiency as a tribotechnical additive to frictional materials. Specimens based on iron, bronze, and copper with addition of fibers have been produced using the methods of powder metallurgy. Tribotechnical behavior of iron and copper-based specimens is comparable both in terms of functions of sliding speed and load on friction contact, and of respective values. Tests of copper-based specimens have demonstrated decrease in the coefficient of friction from 0.44 for pure copper to 0.18 and its stabilization. In addition, despite lower mechanical strength of the copper specimen with fibers in comparison with bronze and iron ones, its wear is not higher and in certain regimes is even significantly lower. It has been established that tribotechnical behavior of copper-based specimens with frictional additive of fibers qualitatively differs from that of iron and bronze-based specimens with the same frictional additive of alumina-based fibers. The difference in tribotechnical behavior of copper-based specimens with fibers is related to formation of an adhesive ceramic layer on the friction track. Formation of a similar layer on iron and bronze specimens is not observed. The formed ceramic layer separates friction surfaces, preventing formation of scores, sticking of friction materials, the coefficient of friction is stabilized, and the wear decreases in wide range of sliding speeds and loads. As a consequence, the operation ranges regarding the allowable sliding speed and loads are significantly expanded.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Material Properties and Applications · Tribology and Wear Analysis · Polymer Science and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. Kablov, E.N., Innovative developments of FSUE VIAM SSC of RF on realization of 'Strategic directions of the development of materials and technologies of their processing for the period until 2030', Aviatsion. Mater. Tekhnol., 2015, no. 1, pp. 3–33. https://doi.org/10.18577/2071-9140-2015-0-1-3-3310.18577/2071-9140-2015-0-1-3-33 ↗
2. Kablov, E.N., New generation materials are the basis of innovation, technological leadership and Russia’s national security, Intellekt Tekhnol., 2016, no. 2 (14), pp. 16–21.
3. Kablov, E.N., Formation of domestic space materials science, Vestn. RFFI, 2017, no. 3, pp. 97–105.10.22204/2410-4639-2017-095-03-97-105 ↗
4. Hrenov, O.V., Dmitrovich, A.A., and Leshok, A.V., Metallokeramicheskie friktsionnye materialy: ucheb.-metod. posobie (Metal-Ceramic Friction Materials, The Textbook), Minsk: BNTU, 2011.
5. Denisova, N.E., Shorin, V.A., Gontar’, I.N., Volchihina, N.I., and Shorina, N.S., Tribotekhnicheskoe materialovedenie i tribotekhnologiya: ucheb. posob. (Tribotechnical Materials Science and Tribotechnology, Textbook), Denisova, N.E., Penza: Penz. Gos. Univ., 2006.
6. Kaczmar, J.W., Granat, K., Grodzka, E., and Kurzawa, A., Tribological properties of Cu based composite materials strengthened with Al2O3 particles, Arch. Foundry Eng., 2013, vol. 13, Spec. Iss. 2, pp. 33–36.10.2478/afe-2013-0037 ↗
7. Kennedy, F.E., Balbahadur, A.C., and Lashmore, D.S., The friction and wear of Cu-based silicon carbide particulate metal matrix composites for brake applications, Wear, 1997, vols. 203–204, pp. 715–721.10.1016/S0043-1648(96)07451-0 ↗
8. Stepanova, E.V. and Zimichev, A.M., Thermal insulation material for cords made of refractory oxide fibers, Tr. VIAM, 2020, no. 2 (86), pp. 72–80. https://doi.org/10.18577/2307-6046-2020-0-2-72-8010.18577/2307-6046-2020-0-2-72-80 ↗
9. Baruzdin, B.V., Varrik, N.M., and Maksimov, V.G., High-temperature fibrous sealing materials, Aviats. Mater. Tekhnol., 2017, no. S, pp. 272–289. https://doi.org/10.18577/2071-9140-2017-0-S-272-28910.18577/2071-9140-2017-0-S-272-289 ↗
10. Babashov, V.G. and Maksimov, V.G., Influence of the material of the counterbody on the tribotechnical characteristics of mullite, in Sovremennye dostizheniya i tendentsii razvitiya v oblasti teplozashchitnykh, keramicheskikh i metallicheskikh kompozitsionnykh materialov (Proceedings of the All-Russia Conference on Modern Achievements and Development Trends in the Field of Heat-Shielding, Ceramic and Metal Composite Materials), 2019, pp. 120–131.
11. Babashov, V.G., Maksimov, V.G., Varrik, N.M., and Samorodova, O.N., Studying of structure and properties of samples of ceramic composite materials on the basis of mullite, Aviatsion. Mater. Tekhnol., 2020, no. 1 (58), pp. 54–63.10.18577/2071-9140-2020-0-1-54-63 ↗
12. Zimichev, A.M., Varrik, N.M., and Sumin, A.V., Research of the process of extrusion of continuous high-melting fibers, Tr. VIAM, 2017, no. 1 (49), p. 6. https://doi.org/10.18577/2307-6046-2017-0-1-6-610.18577/2307-6046-2017-0-1-6-6 ↗
13. Istomin, A.V. and Kolyshev, S.G., Electrostatic method of forming ultrathin fibers of refractory oxides, Aviatsion. Mater. Tekhnol., 2019, no. 2 (55), pp. 40–46.10.18577/2071-9140-2019-0-2-40-46 ↗
14. Fedorchenko, I.M. and Pugina, L.I., Kompozitsionnye spechennye antifriktsionnye materialy (Composite Sintered Anti-Friction Materials), Kiev: Naukova Dumka, 1980.
15. Kuksenova, L.I., Lapteva, V.G., Kolmakov, A.G., and Rybakova, L.M., Metody ispytaniya na trenie i iznos (Friction and Wear Test Methods), Moscow: Intermet Inzhiniring, 2001.