Effect of Vibrations on the Lubricating Film Thickness in a Friction Unit by the Example of Toothed Gearing
Source abstract
Abstract
Relationships are presented that comprehensively connect the lubricating film thickness, circumferential velocity, quasistatic contact stresses, and the vibration accelerations generated by the toothed gearing in the course of operation. The analysis of these interconnections shows that in the case of a toothed gearing, the thickness of the lubricant film is significantly affected by an integrated combination of the circumferential velocity and the quasistatic contact stresses as well as the vibrations generated by the gearing itself, whose combination in many respects determines the damaging factors. With this in mind, gears can be conditionally divided into groups: lightly loaded and heavily loaded, in which an increase in peripheral speed leads to power-law changes in the thickness of the lubricating film and generated vibration accelerations, and gears located between them, in which an increase in peripheral speed has practically no effect on the thickness of the lubricating film, and the effect of its change on the service life can be neglected. It is shown that when assessing gear set service life, tribotechnical, loading, high-velocity characteristics, as well as damage in the local zones of gear-teeth working surfaces should be taken into account. The obtained quantitative results of these studies can be attributed only to a spur toothed gearing tested in the course of operation under contact stresses ranging from 200 to 1150 MPa, circumferential velocity from 3 to 12 m/s, and flood lubrication by Industrial-20 grade oil with a temperature of (20 ± 5)°C. However, these results can be used in the development of methods for a refined prediction of friction unit service life taking into account high-velocity and loading operation modes, as well as generating the vibration accelerations under real operating conditions. Moreover, the established regularities could be to either extent characteristic of lubricated toothed gears as a whole. Taking these regularities into account when designing lubricated toothed gearing used in a wide range of velocity operation modes makes it possible to choose the geometric parameters of gearing, in the case of which the range of contact stresses could provide a minimized effect of velocity and loading factors on the lubricating film thickness, and the associated toothed gearing service life.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Tribology and Wear Analysis · Gear and Bearing Dynamics Analysis · Mechanical Systems and Engineering
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (10)
Show source-provided references
1. Grubin, A.I., Fundamentals of the hydrodynamic theory of lubrication of heavily loaded cylindrical surfaces, Tr. Tsentr. Nauchno-Issled. Inst. Tekhnol. Mahsinostr., 1949, no. 30.
2. Petrusevich, A.I., Osnovnye vyvody iz kontaktno-gidrodinamicheskoi teorii smazki (The Main Conclusions from the Contact-Hydrodynamic Theory of Lubrication), Moscow: Akad. Nauk SSSR, 1951, no. 2, pp. 209–233.
3. Drozdov, Yu.N. and Reshchikov, V.F., The state of the oil film during relative rolling with sliding of heavily loaded bodies, Mashinosvedenie, 1968, no. 4, pp. 115–119.
4. Raiko, M.V., Smazka zubchatykh peredach (Lubrication of Gears), Kiev: Tekhnika, 1970.
5. Basinyuk, Ya.V., Diagnostics of gears for gearing using advanced information technologies for the analysis of changes in the dynamic structures, Extended Abstract of Cand. Sci. (Eng.) Dissertation, Minsk: Joint Inst. Mech. Eng., Natl. Acad. Sci. Bel., 2002.
6. Uss, I.N., Basiniuk, U.L., and Mardosevich, E.I., Monitoring tekhnicheskogo sostoyaniya privodnykh sistem traktorov “Belarus” (Monitoring of the Technical Condition of the Drive Systems of Belarus Tractors), Gomel, 2008.
7. Zakharova, T.V. and Shestakov, O.V., Veivlet-analiz i ego prilozheniya: uchebnoe posobie (Wavelet Analysis and Its Applications: Manual), Moscow: INFRA-M, 2012, 2nd ed.
8. Basiniuk, U.L., Dinamika, shum i smazka zubchatykh peredach (Dynamics, Noise, and Gear Lubrication), Gomel: Inst. Mekh. Metalllopolim. Sist., 2006
9. Al’gin, V.B., et al., Zubchatye peredachi i transmissii v Belarusi: proektirovanie, tekhnologiya, otsenka svoistv (Gears and Transmissions in Belarus: Design, Technology, and Assessment of Properties), Al’gin, V.B. and Starzhinskii, V.E., Eds., Minsk: Belaruskaya Navuka, 2017.
10. Sosnovskii, L.A., Bogdanovich, A.V., and Yelovoy, O.M., Local damages and durability of power systems of mobile machines, Mekh. Mash., Mekh. Mater., 2008, no. 1 (2), pp. 24–29.