Relationship of Morphology and Chemical Composition of the Surface of Doped Diamond-Like Coatings with the Friction Coefficient
Source abstract
Abstract
The prospects for the use of diamond-like carbon coatings in tribology are largely associated with various technologies for their alloying. This paper presents a comprehensive technique for studying silicon-doped diamond-like coatings, including tests for friction in a pair with steel and analysis of the mechanisms of frictional interaction. Experimental samples of the coatings were obtained by plasma-enhanced chemical vapor deposition on a flat steel substrate. Tribological tests were carried out according to the ball–plane scheme with reciprocating motion and differed in the time of the experiment. The morphology and chemical composition of the initial surface and the surface after tibological tests of samples and counterbodies were studied using the methods of scanning electron and probe microscopy. The mechanisms of transformation of surface layers during friction and formation of a protective film of secondary structures on the surface were considered. The effect of these changes on the properties of frictional contact at different silicon content in carbon coatings has been established. The analysis of the influence of load parameters, test duration, and coating composition on the processes of formation of surface antifriction films and their destruction during friction is carried out. With an increase in the load, a decrease in the running-in duration is observed, however, at the same time, the duration of a stable low friction (with coefficient less than 0.1) stage decreases. It is shown that secondary structures, which contribute to a decrease in the coefficient of friction, cover a part of the working surface of the samples and are effective in short-term tests.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Diamond and Carbon-based Materials Research · Metal and Thin Film Mechanics · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. Vetter, J., 60 Years of DLC coatings: historical highlights and technical review of cathodic arc processes to synthesize various DLC types, and their evolution for industrial applications, Surf. Coat. Technol., 2014, vol. 257, pp. 213–240.10.1016/j.surfcoat.2014.08.017 ↗
2. Peter, S., Günther, M., Hauschild, D., Grambole, D., and Richter, F., Mid-frequency deposition of a-C:H films using five different precursors, Vacuum, 2010, vol. 85, pp. 510–513.10.1016/j.vacuum.2010.10.006 ↗
3. Jacob, W. and Möller, W., On the structure of thin hydrocarbon films, Appl. Phys. Lett., 1993, vol. 63, p. 1771.10.1063/1.110683 ↗
4. Robertson, J., Diamond-like amorphous carbon, Mater. Sci. Eng., R, 2002, vol. 37, pp. 129–281.10.1016/S0927-796X(02)00005-0 ↗
5. Hainsworth, S.V. and Uhure, N.J., Diamond like carbon coatings for tribology: production techniques, characterization methods and applications, Int. Mater. Rev., 2007, vol. 52, no. 3, pp. 153–174.10.1179/174328007X160272 ↗
6. Hofmann, D., Kunkel, S., Bewilogua, K., and Wittorf, R., From DLC to Si-DLC based layer systems with optimized properties for tribological applications, Surf. Coat. Technol., 2013, vol. 215, pp. 357–363.10.1016/j.surfcoat.2012.06.094 ↗
7. Grigoriev, S.N., Volosova, M.A., Fedorov, S.V., and Mosyanov, M., Influence of DLC coatings deposited by PECVD technology on the wear resistance of carbide end mills and surface roughness of AlCuMg2 and 41Cr4 workpieces, Coatings, 2020, vol. 10, p. 1038.10.3390/coatings10111038 ↗
8. Zhang, S., Xie, H., Zeng, X., and Hing, P., Residual stress characterization of diamond-like carbon coatings by an X-ray diffraction method, Surf. Coat. Technol., 1999, vol. 122, nos. 2–3, pp. 219–224.10.1016/S0257-8972(99)00298-4 ↗
9. Grigoriev, S.N., Volosova, M.A., Vereschaka, A.A., Sitnikov, N.N., Milovich, F., Bublikov, J.I., Fyodo-rov, S.V., and Seleznev, A.E., Properties of (Cr,Al,Si)N-(DLC-Si) composite coatings deposited on a cutting ceramic substrate, Ceram. Int., 2020, vol. 46, pp. 18241–18255.10.1016/j.ceramint.2020.04.147 ↗
10. Gayathri, S., Kumar, N., Krishnan, R., Ravindran, T.R., Amirthapandian, S., Dash, S., Tyagi, A.K., and Sridharan, M., Influence of transition metal doping on the tribological properties of pulsed laser deposited DLC films, Ceram. Int., 2015, vol. 41, no. 1, pp. 1797–1805.10.1016/j.ceramint.2014.09.125 ↗
11. Orrit-Prat, J., Bonet, R., Rupérez, E., Punset, M., Ortiz-Hernández, M., Guillem-Marti, J., Lousa, A., Cano, D., Díaz, C., García Fuentes, G., and Caro, J., Bactericidal silver-doped DLC coatings obtained by pulsed filtered cathodic arc co-deposition, Surf. Coat. Technol., 2021, vol. 411, art. ID 126977.10.1016/j.surfcoat.2021.126977 ↗
12. Murata, Y., Choo, C.-K., Ono, H., Nagai, Y., and Tanaka, K., Nitrogen-doped DLC thin films prepared by hydrocarbons pyrolysis method, Mater. Today: Proc., 2016, vol. 3, suppl. 2, pp. 197–202.
13. Baia Neto, A.L., Santos, R.A., Freire, F.L., Jr., Camargo, S.S., Jr., Carius, R., Finger, F., and Beyer, W., Relation between mechanical and structural properties of silicon-incorporated hard a-C:H films, Thin Solid Films, 1997, vol. 293, pp. 206–211.10.1016/S0040-6090(96)08948-1 ↗
14. Torskaya, E.V., Muravyeva, T.I., and Sánchez-López, J.C., Study of TiC/a-C(:H) coatings before and after friction by nanoindentation, Proc. 4th Int. Conf. on Industrial Engineering (ICIE 2018), Cham: Springer-Verlag, 2018, pp. 1011–1018.10.1007/978-3-319-95630-5_106 ↗