journal article·2021-12

The Effect of Wear Resistance of Carbide Cutting Tools on the Technological Process Efficiency under Severe Cutting Conditions

I. A. Pinahin, M. Moradi, M. A. Yagmurov, S. S. Vrublevskaya, M. A. Shpack

Journal of Friction and Wear· Volume 42· Issue 6
Publisher page

Abstract

The results of the effect of wear resistance of hard-alloy cutting tools (lathe cutters) treated by volumetric pulsed laser hardening (VPLH) and operating in severe cutting conditions (rough processing, peeling along the casting crust, etc.), on the technological process efficiency of parts processing (processing productivity, operation cost, tool cost) are presented in the study. Bulk pulsed laser hardening was carried out using a solid-state laser with an active element based on yttrium aluminum garnet with neodymium (Nd:YAG LIS-200) in a single, free-running mode. Samples from the VK8M hard alloy were investigated in this study. It is shown that increasing the abrasive wear resistance of carbide cutting tools due to laser hardening allows one to increase the value of the input parameters (cutting modes). In particular, increasing the feed and higher stability of the cutting process, which is expressed in an increase in the technical and economic parameters of processing, taking into account the gamma percentage firmness. The optimal feed rate when working with tools strengthened by volumetric pulsed laser processing increases by 1.2–1.3 times with an increase in processing productivity by 1.1–1.2 times, a decrease in the cost of an operation by 1.1–1.2 times, and reduction of instrumental costs by 1.15–1.25 times. The optimal modes of volumetric pulsed laser hardening were determined in the study: laser beam energy of 200 J (energy density 52 GJ/m2), laser pulse duration of 0.8 ms, and laser beam diameter of 2.0 mm. The optimal modes were then used for hardening cutting tools used in production tests. The results allow recommending the measures for optimization of cutting conditions during wear in severe cutting conditions. More specifically, to prescribe cutting conditions based on the optimal feed value, taking into account the dispersion of tool life (gamma-percentage resistance).
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · Advanced machining processes and optimization · Surface Treatment and Coatings

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. Okhlupin, D.N., Korolev, A.V., and Sinev, I.V., Discrete friction mechanisms of a metal tool with polycrystalline diamond-coated detail, J. Frict. Wear, 2020, vol. 41, no. 6, pp. 538–542.10.3103/S106836662006015X ↗
2. Zemlyanushnova, N.Yu. and Zemlyanushnov, N.A., To the definition of stress-strain state of springs during recovering when hardened, IOP Conf. Ser.: Mater. Sci. Eng., 2020, vol. 971, art. ID 022025.10.1088/1757-899X/971/2/022025 ↗
3. Gonzalez-Ortiza, D., Salameha, C., Bechelanya, M., and Miele, P., Nanostructured boron nitride–based materials: synthesis and applications, Mater. Today: Adv., 2020, vol. 8, pp. 100–107.
4. Lasota, I., Protsenko, V., Matyushkin, A., Kuznetsov, M., and Gook, S., Laser surface hardening of engine camshaft cams, Mater. Today: Proc., 2020, vol. 30, pp. 478–482.
5. Moradi, M., Moghadam, M.K., and Kazazi, M., Improved laser surface hardening of AISI 4130 low alloy steel with electrophoretically deposited carbon coating, Optik, 2018, vol. 178, pp. 614–622.10.1016/j.ijleo.2018.10.036 ↗
6. Moradi, M., Ghorbani, D., Moghadam, M.K., Kazazi, M., Rouzbahani, F., and Karazi, S., Nd:YAG laser hardening of AISI 410 stainless steel: microstructural evaluation, mechanical properties, and corrosion behavior, J. Alloys Compd., 2019, vol. 795, pp. 213–222.10.1016/j.jallcom.2019.05.016 ↗
7. Moradi, M., Arabi, H., Nasab, S.J., and Benyounis, K.Y., A comparative study of laser surface hardening of AISI 410 and 420 martensitic stainless steels by using diode laser, Opt. Laser Technol., 2019, vol. 111, pp. 347–357.10.1016/j.optlastec.2018.10.013 ↗
8. Pinahin, I.A., Yagmurov, M.A., and Vrublevskaya, S.S., Investigation into strength T5K10 hard alloy after volumetric pulsed laser hardening (VPLH), Mater. Today: Proc., 2019, vol. 19, pp. 2221–2225.
9. Pinahin, I.A., Shagrov, M.N., Yagmurov, M.A., Vrublevskaya, S.S., Darzhaniya, A.Yu., and Shpak, M.A., Wear resistance increase of single-carbide hard alloys after bulk pulse-laser hardening, J. Frict. Wear, 2020, vol. 41, no. 6, 554–558.10.3103/S1068366620060161 ↗
10. Bashkov, V.M. and Katsev, P.G., Ispytaniya rezhushchego instrumenta na stoikost’ (Testing of Cutting Tool for Durability), Moscow: Mashinostroenie, 1985.
11. Pinakhin, I.A., Chernigovskii, V.A., Bratsikhin, A.A., Yagmurov, M.A., and Sugarov, Kh.R., Investigation into physicomechanical properties of VK6, VK8, and T5K10 hard alloys after volumetric pulsed laser hardening, Inorg. Mater., 2018, vol. 54, pp. no. 15, 19–22.10.1134/S0020168518150177 ↗
12. Nowotny, S., Berger, L.-M, and Spatzier, J., Coatings by laser cladding, in Comprehensive Hard Materials, Vol. 1: Hardmetals, Amsterdam: Elsevier, 2014, pp. 507–525.10.1016/B978-0-08-096527-7.00018-0 ↗
13. Skibin, V.V. and Abankin, V.I., Feed selection taking into account durability scattering of carbide cutters, in Nadezhnost’ rezhushchego instrumenta (Reliability of the Cutting Tool), Kiev: Vishcha Shkola, 1975, no. 2, pp. 39–42.
14. Ahsan, K., Mazid, A., Clegg, R., and Pang, G., Study on carbide cutting tool life using various cutting speeds for α-β Ti-alloy machining, J. Achiev. Mater. Manuf. Eng., 2012, vol. 55, pp. 600–606.
15. Dörre, A., Huang, C.-Y., and Emura, T., Likelihood-based analysis of doubly-truncated data under the location-scale and AFT model, Comput. Stat., 2021, vol. 36, pp. 242–246.10.1007/s00180-020-01027-6 ↗
16. Klushin, M.I., Rezanie metallov (Metal Cutting), Gorky: Gor’k. Politekh. Inst., 1970.