journal article·2021-07

Influence of Thermal Conductivity of Steels on the Friction Limit Loads on Polyamide

E. B. Sedakova, Yu. P. Kozyrev

Journal of Friction and Wear· Volume 42· Issue 4
Publisher page

Abstract

The results of tribotechnical tests of friction pairs of polyamide–steels of three grades including carbon and alloy steels with considerably different thermal conductivities are presented. It is shown that the thermal conductivity of steels, which is one of their physical and mechanical characteristics, has a significant influence on the polymer temperature in the tribocontact zone. The objective of the research is to determine the maximum load value, at which the contact temperature does not exceed the polyamide melting point during the test period. It is shown that this load can be taken as a limit load for the friction unit, which corresponds to the upper limit of the working load range. In order to determine the limit load, a series of experimental studies of polyamide wear resistance was conducted starting with the high loads of 1.5 MPa m/s and then subsequently reducing the load gradually in each successive series to the level of 0.6 MPa m/s. Under frictional heating, the fact of reaching the polyamide melting point was determined by a sharp increase in the friction coefficient and torque on the motor shaft. After the test was over, an increased polymer wear was recorded, and its considerable adhesion to the steel counterbody surface was observed. The polymer frictional heating was estimated by an improved method for contact temperature calculation using a modified expression to calculate the heat flow distribution coefficient. The method was developed for friction pairs with materials having considerably different heat conductivities. The applicability of the method is confirmed by good agreement of the calculated value of the contact temperature, determined under the load corresponding to the abovementioned external manifestations of scuffing, with the reference values of the polyamide melting temperature. The results of the research are presented in tabular form and in the form of graphic dependences, which can be used for determining the values of limit loads.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Tribology and Wear Analysis · Natural Fiber Reinforced Composites · Polymer Nanocomposites and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (10)

Show source-provided references
1. Spravochnik po plasticheskim massam (Handbook of Plastics), Kataev, V.M., Popov, V.A., and Sazhin, B.I., Eds., Moscow: Khimiya, 1985, 2nd ed.
2. Dul’nev, G.N. and Semyashin, E.M., Teploobmen v elektronnykh apparatakh (Heat Exchange in Electronic Devices), Leningrad: Energiya, 1968.
3. Sedakova, E.B. and Kozyrev, Yu.P., Thermal distribution in the PTFE–steel frictional pair, Russ. Eng. Res., 2016, vol. 36, no. 9, pp. 727–730.10.3103/S1068798X16090227 ↗
4. Amosov, A.P., Elementary Tegako physical models of friction, Izv. Samar. Nauch. Tsentra, Ross. Akad. Nauk, 2011, vol. 13, no. 4 (3), pp. 656–662.
5. Chichinadze, A.V., Berlinger, E.M., Braun, E.D., et al., Trenie, iznos i smazka (tribologiya i tribotekhnika) (Friction, Wear, and Lubrication (Tribology and Tribotechnics)), Chichinadze, A.V., Ed., Moscow: Mashinostroenie, 2003.
6. Myshkin, N.K. and Petrokovets, M.I., Tribologiya (Tribology), Gomel: Inst. Mekh. Metallopolim. Sist., Nats. Akad. Nauk Bel., 2002.
7. Denisova, N.E., Shorin, V.A., Gontar’, I.N., Volchikhina, N.I., and Shorina, N.S., Tribotekhnicheskoe materialovedenie i tribotekhnologiya: uchebnoe posobie (Triboengineering Material Science and Tribological Engineering: Manual), Denisova, N.E., Ed., Penza: Penz. Gos. Univ., 2006.
8. Bahadur, S., The development of transfer layers and their role in polymer tribology, Wear, 2000, vol. 245, nos. 1–2, pp. 92–99.10.1016/S0043-1648(00)00469-5 ↗
9. Sedakova, E.B. and Kozyrev, Yu.P., Polymer thermal loading in the polytetrafluoroethylene–steel friction pair, J. Frict. Wear, 2017, vol. 38, no. 5, pp. 390–394.10.3103/S1068366617050117 ↗
10. Kragel’skii, I.V. and Mikhin, N.M., Uzly treniya mashin. Spravochnik (Friction Units of Machines: Handbook), Moscow: Mashinostroenie, 1984.