journal article·2015-03

Tribological properties of commercially pure copper with different microstructures, in contact with a graphitic material

V. I. Semenov, S. -J. Huang, V. G. Shibakov, L. Sh. Shuster, S. N. Faizova, P. -Ch. Lin

Journal of Friction and Wear· Volume 36· Issue 2
Publisher page

Abstract

In the present work, we report the results of tribological studies on commercially pure copper (Cu 99.9%) in contact a with graphitic material. The samples under study were made with two types of micro-structures, i.e., a coarse-grained (CG) microstructure with an average grain size of 20–60 μm after annealing and a submicrocrystalline (SMC) microstructure with an average grain size of 0.22 μm after severe plastic deformation (SPD) processing through equal-channel angular pressing (ECAP) via the Conform scheme. It has been shown that the SMC samples after ECAP-Conform processing reveal friction coefficients 12–20% lower than in the case of the annealed coarse-grained (CG) sample.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (10)

Show source-provided references
1. Kuptsov, Yu.E., Besedy o tokos″eme (Talks about Current-Collecting), Moscow: Modern-A, 2001.
2. Chichinadze, A.V., Berliner, E.M., Braun, E.D., Busche, N.A., Buyanovskii, I.A., Gekker, F.R., Goryacheva, I.G., Grib, V.V., Demkin, N.B., and Dobychin, M.N., Trenie, iznos i smazka (tribologiya i tribotekhnika) (Friction, Wear and Lubrication (Tribology and Tribotechbique)), Chichinadze, A.V., Ed., Moscow: Mashinostroenie, 2003.
3. Kirshenbaum, V.Ya., Mekhanotermicheskoe formirovanie poverkhnostei treniya (Mechanothermical Formation of Friction Surfaces), Moscow: Mashinostroenie, 1987.
4. Gromakovskii, D.G. Kuznetsov, N.D., et al., Increasing of friction joints durability by carbonfluoride application, Vestn. Mashinostr., 1987, no. 8.
5. Belyi, A.V., Karpenko, G.D., and Myshkin, N.K., Struktura i metody formirovaniya iznosostoikikh poverkhnostnykh sloev (Structure and Methods of Wear-Resistant Surface Layer Formation), Moscow: Mashinostroenie, 1991.
6. Odintsov, L.G., Uprochnenie i otdelka detalei poverkhnostnym plasticheskim deformirovaniem: Spravochnik (Hardening and Finishing of Details by Surface Plastic Deformation. A Handbook), Moscow: Mashinostroenie, 1987.
7. Rybakova, L.M. and Kuksenova, L.I., Struktura i iznosostoikost’ metalla (Structue and Wear-Resistance of Metal), Moscow: Mashinostroenie, 1982.
8. Valiev, R.Z. and Alexandrov, I.V., Nanostrukturnye materialy, poluchennye intensivnoi plasticheskoi deformatsiei (Nanostructured Materials, Produced by Severe Plastic Deformation), Moscow: Logos, 2000.
9. Raab, G.I. and Valiev, R.Z., Equal-Channel Angular Pressing of Long-Length Billets, Tsvetn. Metallurg., 2000, no. 5, pp. 50–53.
10. Semenov, V.I., Shuster, L.Sh., Khuang, S.-D., and Lin, P.-Ch., Tribological behavior of low-carbon steel depending on treatment and structural state, J. Frict. Wear, 2011, vol. 32, pp. 205–211.10.3103/S106836661103010X ↗