A numerical analysis of the elastohydrodynamic line contact film formation at motion start-up
Source abstract
Abstract
A mathematical model is proposed of the process of formation of the elastohydrodynamic (EHD) lubricant layer between resilient cylinders that begin to rotate in the lubricating material medium from the resting state. The model assumes division of the whole contact region into three zones: the zone within which dry motion is described by the equations of the elastohydrodynamic theory of lubrication, the transient zone, and the dry contact zone. The method of the numerical solution of this system of equations is presented. The calculations are performed for the lubricating material that was used in the published experimental study of the process of formation of the EHD lubricating layer between the resilient ball and the flat resilient base. It is shown that the calculation results well agree with the experimental data both qualitatively and quantitatively providing that the transient region dimensions are adequately selected. The function of the pressure distribution, the lubricating layer thickness, the lubricating material flow, the rate of approach of the surfaces over the contact region at different moments of time, the time dependencies of the lubricating layer thickness at different points of the contact region, and the coordinates of the boundary points of the dry contact region is also presented.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Gear and Bearing Dynamics Analysis · Tribology and Lubrication Engineering · Adhesion, Friction, and Surface Interactions
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. Xiaolan, Ai, Haiqing, Yu., A Full Numerical Solution for General Transient Elastohydrodynamic Line Contact and Its Application, Wear, 1988, vol. 121, no. 2, pp. 143–159.10.1016/0043-1648(88)90039-7 ↗
2. Larsson, R., Höglund, E., Numerical Simulation of a Ball Impacting and Rebounding a Lubricated Surface, Trans. ASME. J. of Tribology, 1995, vol. 117, no. 1, pp. 94–102.10.1115/1.2830614 ↗
3. Verner, C. H., Wijnant, Y.H., Validation of EHL Contact Predictions under Time Varying Load, Proc. of I. Mech. E. Part J. J. of Eng. Tribology, 2005, vol. 219, no. 4, pp. 249–261.10.1243/135065005X33865 ↗
4. Jin, Z.M., Yang, P., Cui, J., and Dowson, D.,The Minimum Film Thickness in the Line Contacts during Reversal of Entrainment, Proc. of I. Mech. E. Part J. J. of Eng. Tribology, 2004, vol. 218, no. 3, pp. 211–224.10.1243/1350650041323403 ↗
5. Hooke, C. J., The Minimum Film Thickness in Lubricated Line Contacts during Reversal of Entrainment—General Solution and the Development of a Design Chart, Trans. ASME. J. of Tribology, 1993, vol. 115, no.1, pp. 191–199.10.1115/1.2920975 ↗
6. Hooke, C.J., The Minimum Film Thickness in Lubricated Line Contacts during Reversal of Entrainment—General Solution and the Development of a Design Chart, Proc. of I. Mech. E. Part J. J. of Eng. Tribology, 1994, no. 208, pp. 53–64.10.1243/PIME_PROC_1994_208_349_02 ↗
7. Usov, P.P., Numerical Analysis of Transient Processes in Elastohydrodynamic Contact of Cylinders on Varying the Direction of Rolling Velocity, Trenie i iznos, 2006, vol. 27, no. 1, pp. 43–53.
8. Wang, J., Kaneta, M., and Yang P., Numerical Solution of the TEHL Line Contact Problem under Reciprocating Motion, Tribology International, 2005, vol. 38, no. 2, pp. 165–178.10.1016/j.triboint.2004.07.025 ↗
9. Glovena, R.P., Spikes, H.A., Elastohydrodynamic Film Formation at the Start-up of the Motion, Proc. of I. Mech. E. Part J. J. of Eng. Tribology, 2001, vol. 215, no. 2–3, pp. 125–138.10.1243/1350650011541774 ↗
10. Osborn, K.F., Sadeghi, F., Time Dependent Line EHD Lubrication Using Multigrid/Multilevel Technique, Trans. ASME. J. of Tribology, 1992, no. 114, pp. 68–74.10.1115/1.2920870 ↗
11. Mongkolwongrojn, M. and Thammakosol, K., Theoretical Investigation of Transient Elastohydrodynamic Lubrication with Newtonian Solid-Liquid Lubricant, Lubrication Science, 2005, vol. 17, no. 3, pp. 347–357.10.1002/ls.3010170308 ↗
12. Roelands, C.J.A., Correlation Aspects of Viscosity-Temperature-Pressure Relationship of Lubricating Oils, PhD Thesis, Delft: Delft University of Technology, 1966.
13. Dowson, D., Higginson, G.R., Elastohydrodynamic Lubrication. The Fundamentals of Roller and Gear Lubrication, Oxford: Permagon Press, 1966.