journal article·2024-06

To Increase Wear Resistance of Screw Cylindrical Compression Springs Working with Coil Contacts

N. A. Zemlyanushnov, N. Y. Zemlyanushnova

Journal of Friction and Wear· Volume 45· Issue 3
Publisher page

Abstract

Abstract During operation of springs, especially cyclic buffer and high-speed springs, there are inevitable relative movements of their surfaces, friction, and coil contacts. Due to friction, a lot of energy is converted into thermal energy, this is а cause of spring wear on the contact points of the coils and of overheating of the machines and mechanisms. The known methods of increasing spring resourcefulness do not consider the issue of friction and wear of springs surfaces contact. Тhe new technologies for increasing the wear resistance of compression springs using contact predeformation are presented in the article. In this case, an additional axial load exceeding the load on the spring in the product by more than 5% and determined theoretically at the stage of development of the technological process is applied to the compressed spring coils into contact. The exposure time under axial load is 1–1.5 s. Serial springs were manufactured and two batches of experimental springs were produced using new technologies. The dispersion of the force parameters of the springs of experimental batch No. 1 as compared with serial springs was reduced by 14.3%, and as compared with experimental batch No. 2 by 42.9%. After cyclic tests the decrease of workload for serial springs averaged 1.17%; for springs of experimental batch No. 1, 0.23%; for springs of experimental batch No. 2, 0.45%. Contact clamping not only promotes the formation of useful residual stresses, but also increases the bearing capacity of the springs. The strip of hardened material is formed, which increases the wear resistance of the contacting surfaces of the coils and reduces friction due to parallel layering. On the contact places of the spring coils, the specific pressure decreases and the deformation wear resistance of the springs increases. Therefore, contact clamping should also be considered as a finishing operation to reduce friction on the places of contact of the spring’s coils and increasing their wear resistance.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Mechanical Failure Analysis and Simulation · Engineering Diagnostics and Reliability · Engineering and Environmental Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. Manouchehrynia, R., Abdullah, S., and Singh, S.S.K., Fatigue-based reliability in assessing the failure of an automobile coil spring under random vibration loadings, Eng. Failure Anal., 2022, vol. 131, p. 105808. https://doi.org/10.1016/j.engfailanal.2021.10580810.1016/j.engfailanal.2021.105808 ↗
2. Kong, Y.S., Abdullah, S., Schramm, D., Omar, M.Z., and Haris, S.M., Correlation of uniaxial and multiaxial fatigue models for automobile spring life assessment, Exp. Tech., 2020, vol. 44, no. 2, pp. 197–215. https://doi.org/10.1007/s40799-019-00344-w10.1007/s40799-019-00344-w ↗
3. Manouchehrynia, R., Abdullah, Sh., and Singh Karam Singh, S., Fatigue reliability assessment of an automobile coil spring under random strain loads using probabilistic technique, Metals, 2020, vol. 10, no. 1, p. 12. https://doi.org/10.3390/met1001001210.3390/met10010012 ↗
4. Myung, N., Wang, L., and Choi, N.-S., High-cycle and very high-cycle bending fatigue strength of shot peened spring steel, J. Mech. Sci. Technol., 2021, vol. 35, no. 11, pp. 4963–4973. https://doi.org/10.1007/s12206-021-1015-010.1007/s12206-021-1015-0 ↗
5. Zemlyanushnov, N.A., Zemlyanushnova, N.Yu., and Porokhnya, A.A., Povyshenie resursa vysokonagruzhennykh pruzhin szhatiya. Monografiya (Increasing the Service Life of Highly Loaded Compression Springs: Monograph), Stavropol: Severo-Kavkazskii Fed. Univ., 2019. https://www.elibrary.ru/yyxgix.
6. Zemlyanushnova, N.Yu., Porokhin, A.A., and Zemlyanushnov, N.A., Stress–strain state of the valve spring in an auto engine during plastic hardening, Russ. Eng. Res., 2016, vol. 36, no. 7, pp. 535–540. https://doi.org/10.3103/s1068798x1607019410.3103/s1068798x16070194 ↗
7. Ali, M., Husaini, Putra, T.E., and Ali, N., The needs to investigate the effect of road surface vibrations to the fatigue life of a coil spring, IOP Conf. Ser.: Mater. Sci. Eng., 2019, vol. 602, no. 1, p. 012089. https://doi.org/10.1088/1757-899x/602/1/01208910.1088/1757-899x/602/1/012089 ↗
8. Putra, T.E., Husaini, Ali, N., Machmud, M.N., Bakhtiar, A., and Hendrayana, Analysis of surface failure of coil spring in passenger vehicle suspension system, IOP Conf. Ser.: Mater. Sci. Eng., 2019, vol. 523, no. 1, p. 012072. https://doi.org/10.1088/1757-899x/523/1/01207210.1088/1757-899x/523/1/012072 ↗
9. Putra, T.E., Husaini, Ali, N., Hasanuddin, I., Hendrayana, and Bakhtiar, A., Numerical analysis of the stress leading to fatigue failure on a coil spring of the front suspension of a car, IOP Conf. Ser.: Mater. Sci. Eng., 2019, vol. 523, no. 1, p. 012066. https://doi.org/10.1088/1757-899x/523/1/01206610.1088/1757-899x/523/1/012066 ↗
10. Tebenko, Yu.M., Problemy proizvodstva vysokoskorostnykh pruzhin i puti ikh resheniya. Monografiya (Problems of Production of High-Speed Springs and Ways of Their Solution: Monograph), Stavropol: Mir Dannykh, 2007. https://www.elibrary.ru/slvfep.
11. Information portal on oils, greases, adhesives and technical fluids. https://mirsmazok.ru/plastichnye-smazki/smazki_dlya_pruzhin_sila_treniya/.
12. Shishlin, D.D. and Dudukin, A.I., Influence of riveting on wear resistance of friction units, Nauka i obrazovanie v razvitii promyshlennoi, sotsial’noi i ekonomicheskoi sfer regionov Rossii. IX Vserossiiskie nauchnye Zvorykinskie chteniya: sb. tez. dokl. Vserossiiskoi mezhvuzovskoi nauchnoi konferentsii (Science and Education in the Development of Industrial, Social and Economic Spheres of the Regions of Russia: 9th All-Russian Sci. Zvorykin Readings: Proc. All-Russian Interuniv. Sci. Conf.), Murom, Vladimir oblast: Muromskii Inst. Vladimirskogo Gos. Univ., 2017, p. 965.
13. Muratkin, G.V., Malkin, V.S., and Doronkin, V.G., Osnovy vosstanovleniya detalei i remont avtomobilei. V 2 ch. (Foundations of Machine Elements Recovery and Repair of Cars in Two Parts), part 1: Tekhnologicheskie metody vosstanovleniya detalei i remonta avtomobilei. Uchebnoe posobie (Technological Methods of Automobile Parts Restoration and Repair: Training Manual), Muratkin, G.V., Ed., Tolyatti: Tol’yattinsk. Gos. Univ., 2012. https://www.elibrary.ru/xdigld.
14. Lavrinenko, Yu.A., Belkov, E.G., and Fadeev, V.V., Uprochnenie pruzhin (Spring Strengthening), Ufa: Biznes-Partner, 2002.