Tribotechnical Characteristics of Titanium Nitride Coating for High-Load Friction Clutches
Source abstract
Abstract
The results are presented for studies concerning the tribotechnical properties of titanium nitride coatings under cyclic loading, which is typical for heavily loaded friction clutches. Testing was carried out according to the ball-disk scheme with a cyclic application of contact pressure and short-term slippage. The possibilities of studying the tribotechnical characteristics of friction pairs using a vibration tribometer under different combinations of loading and relative displacement parameters have been demonstrated. The obtained experimental data on TiN–steel friction pairs in the course of sliding in the presence of a lubricating medium indicate a high stability of the friction coefficient under cyclic loads. Increasing friction power in the TiN–steel friction pair does not lead to an abruptly dropping friction coefficient. As the relative movement velocity decreases, the friction coefficient increases. The development of friction disks coated with titanium nitride for highly loaded gearboxes should reduce the dynamic loads in the course of operation originating from the destabilization of the friction coefficient and increase the efficiency and service life thereof.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Tribology and Wear Analysis · Lubricants and Their Additives
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (11)
Show source-provided references
1. Shishkarev, M.P. and Kobzev, K.O., Calculations and design of adaptive friction clutches, Naukovedenie, 2013, no. 5, pp. 1–7.
2. Shishkarev, M.P., Adaptivnye friktsionnye mufty (Adaptive Friction Clutches), Rostov-on-Don: Rostovsk. Gos. Akad. S-kh. Mashinostr., 2002.
3. Osanai, H., Ohnuma, H., and Kato, K., Temperature measurement and durability of the frictional surfaces of paper-based wet frictional materials, Jpn. J. Tribol., 1994, vol. 39, no. 12, pp. 1471–1478.
4. Polyakov, V.S., Barbash, I.D., and Ryakhovskii, O.A., Spravochnik po muftam (Handbook on Clutches), Leningrad: Mahsinostroenie, 1974.
5. Rynkevich, S.A., Tarasik, V.P., Shapovalova, O.A., Reginya, V.V., and Kurstak, V.I., Improvement of the durability of the multi-disk clutch of the hydromechanical transmission of a mobile machine, Vestn. Bel.-Ross. Univ., 2011, no. 1 (30), pp. 65–74.10.53078/20778481_2011_1_65 ↗
6. Khomichev, A.S., Friction elements of modern automatic transmissions: materials, operation conditions, and loads, Vestn. Izhevsk. Gos. Tekh. Univ., 2009, no. 2, pp. 36–38.
7. Shapovalova, O.A. and Leshok, A.V., Analysis of failures of clutches of hydromechanical transmissions and thier reduction, Mekh. Mash., Mekh. Mater., 2011, no. 3 (16), pp. 67–73.
8. Gorbatenko, N.N., et al., Diagnostirovanie gidromekhanicheskikh peredach mobil’nykh mahsin (Diagnostics of Hydromechanical Transmissions of Mobile Machines), Tarasik, V.P., Ed., Mogilev: Bel.-Ross. Univ., 2010.
9. Elagina, O.Yu., Komadynko, A.S., Poleshchuk, E.D., Drangai, L., and Pejakovic, V., Prospects for the use of titanium nitride coatings for contact surfaces of friction clutches, J. Frict. Wear, 2020, vol. 41, no. 1, pp. 25–30.10.3103/S1068366620010067 ↗
10. Crowther, A., Zhang, N., Liu, D.K., and Jeyakumaran, J.K., Analysis and simulation of clutch engagement judder and stick-slip in automotive powertrain systems, Proc. Inst. Mech. Eng.,Part D, 2004, vol. 12, pp. 1427–1446.
11. Berger, E.J., Friction modeling for dynamics system simulation, Appl. Mech. Rev., 2002, vol. 55, no. 6, pp. 535–577.10.1115/1.1501080 ↗