Influence of Adhesive Properties and Surface Texture of Laminated Plywood on Rubber Friction
Source abstract
Abstract
The paper studies the effect of adhesion and surface relief of laminated plywood on rubber friction. Samples of birch plywood are studied, the surfaces of which have different texture and roughness and are made on the basis of two different resins: phenol formaldehyde and melamine. The study of the static and dynamic friction coefficient is carried out on a tribometer according to the ring-disk contact scheme at room temperature of 23°C in the range of normal pressures from 0.1 to 0.5 MPa in dry and lubricated friction mode. The study of the adhesion properties of the coatings was carried out on an atomic force microscope with a 900 nm ball at the tip. The refined contact interaction model of the spherical tip with the plywood surface made it possible to estimate the surface energies of the coatings. The findings show that when using plywood in dry contact only, it is necessary, first of all, to increase the adhesion properties of its surface, for example by introducing filler-adhesives or using a polymer resin with increased adhesive properties as the base of the laminated coating. If it is assumed that liquids or contaminants enter the plywood surface during operation, then the best effect is the application of a two-level texture: deep dents to remove water from the contact area and surface roughness to increase adhesive properties. It should be noted that the roughness on some types of laminated films can change rapidly due to wear, therefore the use of films with increased adhesive properties is an advantage for increasing the adhesive properties of the surface of laminated plywood.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Adhesion, Friction, and Surface Interactions · Mechanical stress and fatigue analysis · Textile materials and evaluations
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Candan, Z., Hiziroglu, S., and McDonald, A.G., Surface quality of thermally compressed Douglas fir veneer, Mater. Des., 2010, vol. 31, no. 7, pp. 3574–3577.10.1016/j.matdes.2010.02.003 ↗
2. Bekhta, P., Proszyk, S., Krystofiak, T., Mamonova, M., Pinkowski, G., and Lis, B., Effect of thermomechanical densification on surface roughness of wood veneers, Wood Mater. Sci. Eng., 2014, vol. 9, no. 4, pp. 233–245.10.1080/17480272.2014.923042 ↗
3. Büyüksarı, Ü., Surface characteristics and hardness of MDF panels laminated with thermally compressed veneer, Composites, Part B, 2013, vol. 44, no. 1, pp. 675–678.10.1016/j.compositesb.2012.01.087 ↗
4. Dorn, M., Habrová, K., Koubek, R., and Serrano, E., Determination of coefficients of friction for laminated veneer lumber on steel under high pressure loads, Friction, 2021, vol. 9, pp. 367–379.10.1007/s40544-020-0377-0 ↗
5. Yang, X., Luo, X., and Cai, Y., Frictional characteristic of micro structures for wooden pallets, Proc. 2017 World Congr. on Micro and Nano Manufacturing, Kaohsiung, 2017, pp. 1–4.
6. Li, W.G. and Zhang, Z.K., The effect of micro-pits texture on the coefficient of friction between wood and cemented carbide under different wood moisture content, Wood Res., 2019, vol. 64, no. 4, pp. 731–742.
7. Sachek, B.Ya. and Mezrin, A.M., Studies on the tribological characteristics of euro-pallets on film-faced plywood, J. Frict. Wear, 2020, vol. 41, no. 3, pp. 277–281.10.3103/S1068366620030150 ↗
8. Bjerremand, C., Larsen, J., and Hinge, M., Temperature- and time dependency on high friction poly(styrene-co-butyl methacrylate) coated paper, Tribol. Int., 2016, vol. 103, pp. 261–265.10.1016/j.triboint.2016.07.006 ↗
9. Bjerremand, C., Larsen, J., and Hinge, M., Macroscale load and temperature dependency on high friction poly(styrene-co-butyl methacrylate)-coated paper, Tribol. Lett., 2018, vol. 66, no. 1, p. 13.10.1007/s11249-017-0965-y ↗
10. Handbook of Micro/Nanotribology, Bhushan, B., Ed., Boca Raton: CRC Press, 2000, 2nd ed.
11. Grunlan, J.C., Xia, X., Rowenhorst, D., and Gerberich, W.W., Preparation and evaluation of tungsten tips relative to diamond for nanoindentation of soft materials, Rev. Sci. Instrum., 2001, vol. 72, no. 6, pp. 2804–2810.10.1063/1.1370564 ↗
12. Fujinami, S., Ueda, E., Nakajima, K., and Nishi, T., Analytical methods to derive the elastic modulus of soft and adhesive materials from atomic force microcopy force measurements, J. Polym. Sci., Part B: Polym. Phys., 2019, vol. 57, pp. 1279–1286.10.1002/polb.24871 ↗
13. Borodich, F.M. and Galanov, B.A., Non-direct estimations of adhesive and elastic properties of materials by depth-sensing indentation, Proc. R. Soc. A, 2008, vol. 464, pp. 2759–2776.10.1098/rspa.2008.0044 ↗
14. Lin, Z., Yu, Z., and Wei, Y., Measurement of nanoindentation properties of polymers considering adhesion effects between AFM sharp indenter and material, J. Adhes. Sci. Technol., 2020, vol. 34, no. 15, pp. 1591–1608.10.1080/01694243.2020.1714117 ↗
15. Grierson, D.S., Flater, E.E., and Carpick, R.W., Accounting for the JKR–DMT transition in adhesion and friction measurements with atomic force microscopy, J. Adhes. Sci. Technol., 2005, vol. 19, nos. 3–5, pp. 291–311.10.1163/1568561054352685 ↗
16. Maugis, D., Adhesion of spheres: the JKR-DMT transition using a dugdale model, J. Colloid Interface Sci., 1992, vol. 150, no. 1, pp. 243–269.10.1016/0021-9797(92)90285-T ↗
17. Morozov, A.V. and Petrova, N.N., Method of evaluating the coefficient of friction of frost-resistant sealing rubbers, J. Frict. Wear, 2016, vol. 37, no. 2, pp. 124–128.10.3103/S1068366616020124 ↗
18. Goryacheva, I.G., Makhovskaya, Yu.Yu., Morozov, A.V., and Stepanov, F.I., Trenie elastomerov. Modelirovanie i eksperiment (Friction of Elastomers: Modeling and Testing), Moscow: Inst. Komp’yut. Issled., 2017.
19. Goryacheva, I.G. and Makhovskaya, Yu.Yu., Adhesive interaction of elastic bodies, J. Appl. Math. Mech., 2001, vol. 65, no. 2, pp. 273–282.10.1016/S0021-8928(01)00031-4 ↗
20. Hybrid parameters. https://www.taylor-hobson.com/resource-center/faq/what-are-hybrid-parameters.
21. Savkoor, A.R., On the friction of rubber, Wear, 1965, vol. 8, no. 3, pp. 222–237.10.1016/0043-1648(65)90161-4 ↗
22. Goryacheva, I. and Makhovskaya, Yu., Adhesion effect in sliding of a periodic surface and an individual indenter upon a viscoelastic base, J. Strain Anal. Eng. Des., 2016, vol. 51, no. 4, pp. 286–293.10.1177/0309324715614194 ↗