journal article·2021-10

Regarding the Question of Calculation of Contact Pressure in Metal-Polymer Plain Bearings during Wear

M. V. Chernets, A. A. Kornienko, M. I. Pashechko, Yu. M. Chernets, A. I. Dukhota

Journal of Friction and Wear· Volume 42· Issue 5
Publisher page

Abstract

A method for calculating hybrid (metal-polymer) plain bearings for contact strength (bearing capacity) is presented. The method takes into account a significant difference in the mechanical properties of the shaft and bushing materials, in particular, Young’s moduli (by a factor of 40–100). Numerical studies of metal-polymer bearings with a bushing made of two types of PA6 polyamide based composites filled with glass (30% GF) or carbon (30% CF) dispersed fibers are carried out. It is found that, for the accepted calculation data, the maximum contact pressures increase in proportion to the square root of the increase in the external load on the bearing, regardless of the radial clearance and bushing material; an increase in contact pressures is proportional to an increase in the radial clearance in the joint; in a carbon composite bushing with higher Young’s modulus ЕCF, the pressures will be $$\sqrt {{{{{E}_{{{\text{CF}}}}}} \mathord{\left/ {\vphantom {{{{E}_{{{\text{CF}}}}}} {{{E}_{{{\text{GF}}}}}}}} \right. \kern-0em} {{{E}_{{{\text{GF}}}}}}}} $$ times higher on average than in a glass composite bushing with modulus ЕGF. The results of the numerical solution by the developed method of contact mechanics are compared with the results of the solution according to the simplest technique used in engineering practice for calculating the contact pressures in plain bearings according to the criterion of average pressure, and it is shown that this simplest technique is unreasonable, because there is a significant difference (4.0–9.7 times) between the average contact pressures and the maximum pressures. The practical significance of the developed method lies in the fact that with its use it is possible to calculate the contact and wear contact pressures in the design calculation of the metal-polymer plain bearings in contrast to the methods known in the literature for solving this wear-contact problem.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Tribology and Wear Analysis · Polymer Science and Applications · Material Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. Panasyuk, V.V. and Teplii, M.I., Deyaki kontaktni zadachi teorii pruzhnosti (The Contact Problems of the Theory of Elasticity), Kiev: Naukova Dumka, 1975.
2. Rezaei, A., Ost, W., van Paepegem, W., De Baets, P., and Degrieck, J., Experimental study and numerical simulation of the large-scale testing of polymeric composite journal bearings: three-dimensional and dynamic modeling, Wear, 2011, vol. 270, pp. 431–438.10.1016/j.wear.2010.11.005 ↗
3. Rezaei, A., Ost, W., van Paepegem, W., De Baets, P., and Degrieck, J., A study on the effect of the clearance on the contact stresses and kinematics of polymeric composite journal bearings under reciprocating sliding conditions, Tribol. Int., 2012, vol. 48, pp. 8–14.10.1016/j.triboint.2011.06.031 ↗
4. Kuz’menko, A.G., Razvitie metodov kontaktnoi tribomekhaniki (Development of Methods of Contact Tribomechanics), Khmelnytskyi: Khmel’nits. Nats. Univ., 2010.
5. Sorokatyi, R.V., Modeling the behavior of tribosystems using the method of triboelements, J. Frict. Wear, 2002, vol. 23, no. 1, pp. 12–18.
6. Sorokatyi, R.V., Pisarenko, V.G., and Dykha, M.A., Analysis of wear surface geometry formation in plain bearings with misaligned shaft and bush axes, J. Frict. Wear, 2013, vol. 34, no. 4, pp. 274–280.10.3103/S1068366613040119 ↗
7. Zwieżycki, W., Prognozowanie Niezawodności Zużywających się Elementów Maszyn, Radom: ITE, 1999.
8. Wielieba, W., Bezobsługowe Łożyska Ślizgowe z Polimerów Termoplastycznych, Wrocław: Wyd. Politech. Wrocław., 2013.
9. Chernets, M.V., Shil’ko, S.V., Pashechko, M.I., and Barshch, M., Wear resistance of glass- and carbon-filled polyamide composites for metal-polymer gears, J. Frict. Wear, 2018, vol. 39, no. 5, pp. 361–364.10.3103/S1068366618050069 ↗
10. Chernets, M. and Chernets, J., Generalized method for calculating the durability of sliding bearings with technological out-of-roundness of details, Proc. Inst. Mech. Eng., Part J, 2015, vol. 229, no. 2, pp. 16–226.
11. Chernets, M., Evaluation of the contact strength and durability of plain bearings with different types of shaft lobing, Proc. Inst. Mech. Eng., Part J, 2015, vol. 229, no. 12, pp. 1444–1454.
12. Budynas, R.G. and Nisbett, J.K., Shigley’s Mechanical Engineering Design, New York: McGraw-Hill, 2019, 11th ed.