Influence of microplasma machining on the surface structure and microgeometry and tribological behavior of structural alloys
Source abstract
Abstract
Experimental investigation results of local interaction of microplasma discharges with samples made of different structural and triboengineering materials—namely, nickel-chrome (Ni-Cr), cobalt-chrome (Co-Cr), aluminum (B95) alloys, steel 45, and titanium BT1—are presented. A melted region is shown to arise in the surface layer of these materials, characterized by changed microgeometry and structural and tribological properties. In Ni-Cr alloys, microplasma machining enhances the maximum safe pressure in the joint by four times as compared to traditional sand-blasting, while decreasing friction losses by more than 1.5 times. Similar results are obtained for Co-Cr alloys. In B95 and BT1 alloys, the maximum safe pressure increases by 5 and 2.8 times and the coefficient of friction decreases by 3.1 and 3.3 times, respectively. Microplasma machining has the highest effect on steel 45: the maximum safe pressure increases sharply, the wear drops by four times, and the coefficient of friction decreases by 11 times.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Tribology and Wear Analysis · Surface Treatment and Coatings · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (10)
Show source-provided references
1. Atamanov, M.V., Vasiliev, V.I., Zaitsev, V.V., et al., New Technologies for Increasing Machine Part Strength, Avtomobil’nyi transport, 1995, no. 7, pp. 31–33.
2. Semenov, A.P., Kovsh, I.B., Petrova, I.M., et al., Metody i sredstva uprochneniya poverkhnostei detalei mashin kontsentrirovannymi potokami energii (Methods and Means for Hardening of Machine Part Surfaces by Concentrated Energy Flows), Moscow: Nauka, 1992.
3. Ivanov, V.A., Excitement and Effect of Microplasma Discharges on Metals and Alloys in the Plasma of High-Frequency Jet, Prikl. Fiz., 2001, no. 2, pp. 5–39.
4. Ivanov, V.A., Pleshivtsev, N.V., Prokhorov, V.N., and Chachin, N.E., SHF-Discharge Plasma Hardening of Bus Part Surfaces, IV Vserossiiskaya konferentsiya po modifikatsii svoistv konstruktsionnykh materialov puchkami zaryazhennykh chastits (Proc. IV All-Russian Conf. on Modification of Structural Material Properties by Charged Particle Bundles), Tomsk, 1996, pp. 407–409.
5. Ivanov, V.A., Hardening of Metals by Microwave Discharge Plasma, XXVI Zvenigorodskaya konferentsii po fizike plazmy i UTS (Proc. XXVI Zvenigorod Conf. on Plasma Physics and UTS) Zvenigorod, 1999, p. 247.
6. Ivanov, V.A., Konyzhev, M.E., and Spirin, A.M., Formation of Surface Microrelief of Ni-Cr Alloy in Microplasma Discharges, XXX Zvenigorodskaya konferentsiya po fizike plazmy i UTS, (Proc. XXX Zvenigorod Conf. On Plasma Physics and UTS), Moscow: 2003, p. 204.
7. Ivanov, V.A., Konyzhev, M.E., Spirin, A.M., et al., Formation of Strong Microrelief on the Surface of Ni-Cr Alloy in Interaction with Microplasma Discharges, Prikl. Fiz., 2006, no. 6, pp. 97–107.
8. Rybakova, L.M. and Kuksenova, L.I., Struktura i iznosostoikost’ metalla (Structure and Wear Resistance of Metal), Moscow: Mashinostroenie, 1982.
9. Kuksenova, L.I., Lapteva, V.G., and Rybakova, L.M., Metody ispytanii na trenie i iznos (Friction and Wear Test Methods), Moscow: Intermet Inzhiniring, 2001.
10. Ivanov, V.A., Konyzhev, M.E., and Sakharov, A.S., Excitement of Microplasma Discharges on Dielectric Film-Coated Metals, Prikl. Fiz., 2006, no. 6, pp. 114–121.