Surface Microgeometry and Microstructure of the Gas Laser Cut of a Two-Layer Steel Material
Source abstract
Abstract
Gas laser cutting technology has several advantages over other methods of material separation. Reducing the roughness of the cut surface is practically an important task, since the roughness parameters have a significant effect on the operational properties of functional surfaces. The article presents the results of a comprehensive assessment of the microgeometry of the surface of a gas laser cut and studies of the microstructure of a two-layer steel material, high-speed steel grade Р9M4K8, deposited on 30KhGSA structural steel. The influence of the modes of gas laser cutting (cutting speed and laser radiation power) on the parameters of roughness, phase composition, and microhardness of the cut surface layers is investigated. It is shown that the roughness of the cut surface is comparable to the roughness of surfaces after machining and under certain conditions can be less than after mechanical or oxygen cutting. It is shown that the roughness parameters change depending on the distance to the upper edge of the cut. Correlation ratios of the main parameters of surface roughness after gas laser cutting have been determined and compared with similar ratios for surfaces after machining. It is also shown that the height parameters of roughness significantly depend on the cutting modes. No noticeable effect of the chemical composition of steels on the roughness of the cut surface was revealed. Analysis of the microstructure of the surface of steels after gas laser cutting showed that in the surface layer of the cut to a depth of more than 200 microns, the steels were re-hardened. In the hardening zone, the surface layer has an increased microhardness: for high-speed Р9M4K8 steel HV0.2 = 8760 ± 150 MPa, for 30KhGSA steel, HV0.2 = 6740 ± 90 MPa. The results make it possible to select the technological parameters of gas laser cutting that provide an optimal combination of microgeometry and mechanical properties of the cut surface, which makes it possible to reduce or eliminate subsequent processing.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Engineering Technology and Methodologies · Surface Treatment and Coatings · Material Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (9)
Show source-provided references
1. Grigor’yants, A.G., Shiganov, I.N., and Misyurov, A.I., Tekhnologicheskie protsessy lazernoi obrabotki (Technological Processes of Laser Treatment), Moscow: Mosk. Gos. Univ. im. N.E. Baumana, 2006.
2. Sobih, M., Crouse, P.L., and Li, L., Striation-free fiber laser cutting of mild steel sheets, Appl. Phys. A, 2008, vol. 90, no. 1, pp. 171–174.10.1007/s00339-007-4247-7 ↗
3. Tani, G., Tomesani, L., Campana, G., and Fortunato, A., Quality factors assessed by analytical modeling in laser cutting, Thin Solid Films, 2004, vol. 453, pp. 486–491.10.1016/j.tsf.2003.11.260 ↗
4. Wee, L.M. and Li, L., An analytical model for striation formation in laser cutting, Appl. Surf. Sci., 2005, vol. 247, nos. 1–4, pp. 277–284.10.1016/j.apsusc.2005.01.143 ↗
5. Whitehouse, D., Surfaces and Their Measurement, Amsterdam: Elsevier, 2004.
6. Eksler, L.I., Metrologicheskie i tekhnologicheskie issledovaniya kachestva poverkhnosti (Metrological and Technological Studies of Surface Quality), Riga: Zinatne, 1976, pp. 37–42.
7. Izmailov, V.V. and Novoselova, M.V., Kontakt tverdykh tel i ego provodimost’: monografiya (Contact of Solids and Its Conductivity: Monograph), Tver: Tversk. Gos. Tekh. Univ., 2010.
8. Grigor’ev, A.Ya., Fizika i mikrogeometriya tekhnicheskikh poverkhnostei (Physics and Microgeometry of Technical Surfaces), Minsk: Belarusskaya Navuka, 2016.
9. Afanasieva, L.E., Barabonova, I.A., Ratkevich, G.V., Novoselova, M.V., and Grechishkin, R.M., Surface micromorphology and abrasive wear resistance of tool steel after gas-laser cutting, J. Surf. Invest.: X-Ray, Synchrotron Neutron Tech., 2016, vol. 10, no. 6, pp. 1231–1238.10.1134/S1027451016050232 ↗